SRP-2305 30W DALI DT6 LED Dimmable Drive Instructions

SRP-2305 30W DALI DT6 LED Dimmable Drive

Product Information

The 30W DALI DT6 LED Dimmable Driver is a constant current LED controlled device. It has a single channel output and is designed to be used with a DALI signal input. The driver has selectable current options ranging from 250mA to 600mA and a DC voltage range of 8-55V. It also has an output selectable current range from 650mA to 1000mA and a DC voltage range of 8-46V to 8-30V. The driver has a maximum rated power of 30W and operates within a voltage range of 200-240V AC. It has a power factor of over 0.9, low total harmonic distortion (THD) of 12% at full load, and an efficiency of 83% at full load. The driver has a dimming interface and can be controlled via DALI protocol. It has a dimming range and dimming method that can be set using the provided DIP switches. The driver operates within a working temperature range and environment specified by the manufacturer. It has a maximum case temperature, working humidity, and storage temperature & humidity that should be adhered to for optimal performance.

Product Usage Instructions

1. Prior to installation, read all instructions in the user manual.
2. Ensure that the input power supply is within the specified range of 200-240V AC.
3. Select the desired operation current by adjusting the DIP switches on the driver. Choose from the available options: 250mA, 300mA, 350mA, 400mA, 450mA, 500mA, 550mA, or 600mA.
4. Connect the DALI signal input to the driver using the appropriate wiring.
5. Set the desired output current by adjusting the DIP switches on the driver. Choose from the available options: 650mA, 700mA, 750mA, 800mA, 850mA, 900mA, 950mA, or 1000mA.
6. Connect the LED load to the driver’s output channel.
7. Ensure that the dimming interface is connected to the appropriate control system using DALI protocol.
8. Configure the dimming range and dimming method according to your requirements by adjusting the DIP switches on the driver.
9. Place the driver in a suitable location within the specified working temperature range and environment.
10. Ensure that the maximum case temperature, working humidity, and storage temperature & humidity limits are not exceeded.

For further details and troubleshooting, refer to the complete user manual provided with the product.

LED Controlled Device

Important: Read All Instructions Prior to Installation

Function introduction

Product Data

Dips to set the operation current

• Dimmable DALI DT6 LED driver
• In compliance with IEC 62386-101:2014, IEC 62386-102:2014, IEC 62386-207 Ed2
• Built-in DALI-2 interface, DALI DT6 device
• Hybrid dimming method, smooth and deep dimming to 0.1%, flicker free
• 1 channel constant current output, max. output power 30W
• Output current 250mA-1000mA selectable by dip switches
• Standby power consumption less than 0.5W
• Class 2 power supply, full isolated plastic case
• High power factor and efficiency
• DALI DT6 device to control ON/OFF，light intensity output via a single DALI address
• Compatible with universal DALI masters that support DT6 commands
• IP20 rating, suitable for indoor LED lighting applications
• 5 years warranty

Safety & Warnings

• DO NOT install with power applied to device.
• DO NOT set operation current with power applied to device.
• DO NOT expose the device to moisture.

Operation

1. DALI Address Assigned by DALI Masters
   1 DALI address can be assigned by DALI Master controller automatically, please refer to user manuals of compatible DALI Masters for specific operations.

2. Power On Level
   Power on level is a DALI parameter that defines the level of a control gear after power is restored. The factory default power on level for this driver is 100, which means the driver will be at 100% intensity when power is restored.

3. Push Dimmer Mode
   While connected with a AC PUSH, it means Push Dimmer Mode, and operations under Push Dimmer Mode are as follows:

4. Click the button to switch ON/OFF

5. Press and hold down the button to increase or decrease light intensity to desired level and release it, then repeat the operation to adjust light intensity to opposite direction. The dimming range is from 0.1% to 100%.

6. Memory function after power off or power failure enables the device to memorize the status before power off while power on again.

Wiring Diagram

With DALI Bus

With PUSH Dimmer

Product Dimension

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>