JOCEL JLR014092 Washing Machine Instruction Manual

: June 13, 2024
: JOCEL

Table of Contents

JOCEL JLR014092 Washing Machine
PRODUCT INFORMATION
INSTALLATION
OPERATING THE PRODUCT
MAINTENANCE AND CLEANING
TROUBLESHOOTING
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JOCEL JLR014092 Washing Machine

JOCEL-JLR014092-Washing-Machine-PRODUCT

PRODUCT INFORMATION

MODEL NO : JOCEL JLR014092

IMPORTANT INSTRUCTIONS FOR SAFETY AND ENVIRONMENT

This section contains safety instructions that will help protect you from the risk of personal injury or property damage. Failure to follow these instructions shall void any warranty.

GENERAL SAFETY

This product can be used by children at and above 8 years old and by persons whose physical, sensory or mental capabilities were not fully developed or who lack experience and knowledge provided that they are supervised or trained on the safe usage of the product and the risks it brings Children must not play with the product. Cleaning and maintenance work should not be performed by children unless they are supervised by someone. Children of less than 3 years should be kept away unless continuously supervised.
Never place the product on a carpet-covered Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems with your product.
If the product has a failure, it should not be operated unless it is repaired by the Authorized Service Agent. There is the risk of electric shock!
This product is designed to resume operating in the event of powering on after a power interruption. If you wish to cancel the programme, see the “Cancelling the programme” Section.
Connect the product to a grounded outlet protected by a 16 A fuse. Do not neglect to have the grounding installation made by a qualified electrician. Our company shall not be liable for any damages that will arise when the product is used without grounding by the local
The water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, there is the risk of water leakage.
Never open the loading door or remove the filter while there is still water in the Otherwise, risk of flooding and injury from the hot water will occur.
Do not force open the locked loading door. The loading door will be ready to open just a few minutes after the washing cycle comes to an In case of forcing the loading door to open, the door and the lock mechanism may get damaged.
Unplug the product when not in
Never wash the product by spreading or pouring water onto it! There is the risk of electric shock!
Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by grabbing the plug.
Use detergents, softeners and supplements suitable for automatic washing machines
Follow the instructions on the textile tags and the detergent
The product must be unplugged during installation, maintenance, cleaning and repairing
The repairing procedures must be always carried out by the Technical Manufacturer and shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.
If the power cable is damaged, it must be replaced by Technical Assistance to avoid possible risks.
Place the product on a rigid, flat and level
Do not place it on a long-pile rug or similar
Do not place the product on a high platform or near the edge of a cascaded
Do not place the product on the power
Never use a sponge or scrub These will damage the painted, chrome-plated and plastic surfaces.
The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1MPa).
Do not use old or used water inlet hoses on the new It may cause stains on your laundry.
Never place the product on a carpet-covered Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems with your product.

INTENDED USE

This product has been designed for domestic It is not suitable for commercial use and it must not be used out of its intended use.
The product must only be used for washing and rinsing of laundry that are marked
The manufacturer waives any responsibility arising from incorrect usage or
The service life of your product is 10 During this period, original spare parts will be available to operate the appliance properly.
This appliance is intended to be used in household and similar applications such as:
- Staff kitchen areas in shops, offices and other working environments;
- Farm houses;
- By clients in hotels, motels and other residential-type environments;
- Bed and breakfast type environments;
- Areas for communal use in blocks of flats or in

CHILDREN’S SAFETY

Packaging materials are dangerous to children. Keep packaging materials in a safe place away from the reach of the children.
Electrical products are dangerous for children. Keep children away from the product when it is in use. Do not let them tamper with the product. Use child lock to prevent children from intervening with the product.
Do not forget to close the loading door when leaving the room where the product is
Store all detergents and additives in a safe place away from the reach of the children by closing the cover of the detergent container or sealing the detergent package.

WARNING : While washing the laundry at high temperatures, the loading door glass becomes hot. Therefore, keep especially the children away from the loading door of the match while the washing operation is in progress.

PACKAGE INFORMATION

Packaging materials of the product are manufactured from recyclable materials by our National Environment Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

DISPOSING OF THE WASTE PRODUCT

This product has been manufactured with high-quality parts and materials which can be reused and are suitable for Therefore, do not dispose of the product with normal domestic waste at the end of its service life. Take it to a collection point for the recycling of electrical and electronic equipment. Please consult your local authorities to learn the nearest collection point. Help protect the environment and natural resources by recycling used products. For children’s safety, cut the power cable and break the locking mechanism of the loading door so that it will be non-functional before disposing of the product.

COMPLIANCE WITH WEEE DIRECTIVE
This product complies with the EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE). This product has been manufactured with high-quality parts and materials which can be reused and are suitable for recycling. Do not dispose of the waste product with normal domestic and other wastes at the end of its service life. Take it to the collection centre for the recycling of electrical and electronic equipment. Please consult your local authorities to learn about these collection centres.

Compliance with RoHS Directive:
The product you have purchased complies with the EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.

INSTALLATION

This product must be installed by an accredited technician. To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the Technical Assistance. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out.

Preparation of the location and electrical, tap water and waste water installations at the place of installation is under the customer’s responsibility. Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.

WARNING : Installation and electrical connections of the product must be carried out by the Authorized Service Agent. Manufacturers shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.
WARNING : Before installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety.

APPROPRIATE INSTALLATION LOCATION

Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.
Place the product on a solid and flat floor that has sufficient load-carrying capacity!
Do not place the product on the power cable.
Do not install the product at places where the temperature may fall below 0ºC.
Place the product at least 1 cm away from the edges of other furniture.

REMOVING PACKAGING REINFORCEMENT

Tilt the machine backwards to remove the packaging reinforcement.
Remove the packaging reinforcement by pulling the ribbon.

REMOVING THE TRANSPORTATION LOCKS

WARNING : Do not remove the transportation locks before taking out the packaging reinforcement.
WARNING : Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be damaged.

Loosen all the bolts with a suitable spanner until they rotate freely (C).
Remove transportation safety bolts by turning them gently.
Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)

Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future. Never move the product without the transportation safety bolts properly fixed in place!

CONNECTING WATER SUPPLY
The water supply pressure required to run the product is between 1 to 10 bars (0.1 1 MPa). It is necessary to have 10 80 litres of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure-reducing valve if the water pressure is higher.

WARNING: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate.

WARNING: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.

Tighten all hose nuts by hand. Never use a tool when tightening the nuts.
Open the taps completely after making the hose connection to check for water leaks at the connection points. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. To prevent water leakages and damages caused by them, keep the taps closed when the machine is not in use.

CONNECTING TO THE DRAIN

The end of the drain hose must be directly connected to the wastewater drain or the washbasin.
WARNING: Your house will be flooded if the hose comes out of its housing during water discharge. Moreover, there is a risk of scalding due to high washing temperatures! To prevent such situations and to ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so that it cannot come out.
The hose should be attached to a height of at least 40 cm and 100 cm at most.
In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure.
To prevent the flow of dirty water back into the machine and to allow for easy discharge, do not immerse the hose end into the dirty water or drive it in the drain more than 15 cm. If it is too long, cut it short.
The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine.
If the length of the hose is too short, use it by adding an original extension hose. The length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp so as not to come off and leak.

ADJUSTING THE FEET

WARNING : To ensure that the product operates more silently and vibration-free, it must stand level and balance on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and cause crushing and vibration problems.

Loosen the lock nuts on the feet by hand.
Adjust the feet until the product stands level and balanced.
Tighten all lock nuts again by hand.

WARNING: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.

ELECTRICAL CONNECTION
Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be liable for any damages that will arise when the product is used without grounding by local regulations.

Connection must comply with national regulations.
The power cable plug must be within easy reach after installation.
If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician install a 16 Amp fuse.
The voltage specified in the “Technical specifications” section must be equal to your mains voltage.
Do not make connections via extension cables or multiplugs.

WARNING : Damaged power cables must be replaced by the Technical Assistance.

TRANSPORTATION OF THE PRODUCT

Unplug the product before transporting it.
Remove the water drain and water supply connections.
Drain all water that has remained in the product. (SEE 5.5)
Install transportation safety bolts in the reverse order of removal procedure; (SEE 2.3)

Never move the product without the transportation safety bolts properly fixed in place!

WARNING : Packaging materials are dangerous to children. Keep packaging materials in a safe place away from the reach of the children.

PREPARATION

SORTING THE LAUNDRY

Sort laundry according to type of fabric, colour, and degree of soiling and allowable water
Always obey the instructions given on the garment

PREPARING LAUNDRY FOR WASHING

Laundry items with metal attachments such as underwired bras, belt buckles or metal buttons will damage the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillowcase.
Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and brush. Such objects may damage the product or cause noise problems.
Put small size clothes such as infant’s socks and nylon stockings in a laundry bag or pillow
Place curtains in without compressing Remove curtain attachment items.
Fasten zippers, sew loose buttons and mend rips and
Wash “machine washable” or “hand washable” labelled products only with an appropriate
Do not wash colours and whites New, dark-colored cottons release a lot of dye. Wash them separately.
Tough stains must be treated properly before If unsure, check with a dry cleaner.
Use only dyes/colour changers and limescale removers suitable for the machine Always follow the instructions
Wash trousers and delicate laundry turned inside
Keep laundry items made of Angora wool in the freezer for a few hours before This will reduce pilling.
Laundry that is subjected to materials such as flour, lime dust, and milk powder, intensely must be shaken off before being placed into the machine. Such dust and powders on the laundry may build up on the inner parts of the machine in time and can cause damage.

THINGS TO BE DONE FOR ENERGY SAVING

The following information will help you use the product in an ecological and energy-efficient manner.

Operate the product in the highest capacity allowed by the program you have selected, but do not overload; see, “Program and consumption table”.
Always follow the instructions on the detergent
Wash slightly soiled laundry at low
Use faster programs for small quantities of lightly soiled
Do not use prewash and high temperatures for laundry that is not heavily soiled or
If you plan to dry your laundry in a dryer, select the highest spin speed recommended during the washing process.
Do not use detergent over the amount recommended on the detergent package

INITIAL USE
Before starting to use the product, make sure that all preparations are made according to the instructions in the sections “Important safety instructions” and “Installation”. To prepare the product for washing laundry, perform the first operation in the Drum Cleaning program. If your product is not equipped with a Drum Cleaning program, perform the Initial Use procedure by the methods described under the “5.2 Cleaning the loading door and the drum” section of the user manual.

Use an anti-limescale suitable for the washing machines. Some water might have remained in the product due to the quality control processes in the production. It is not harmful to the product.

CORRECT LOAD CAPACITY

The maximum load capacity depends on the type of laundry, the degree of soiling and the washing program desired.
The machine automatically adjusts the amount of water according to the weight of the loaded laundry.

WARNING : Follow the information in the “Program and Consumption table”. When overloaded, the machine’s washing performance will drop. Moreover, noise and vibration problems may occur.

LOADING THE LAUNDRY

Open the loading door.
Place laundry items loosely into the machine.
Push the loading door to close until you hear a locking sound. Ensure that no items are caught in the door.

The loading door is locked while a program is running. The door can only be opened a while after the program comes to an end.

WARNING : In case of misplacing the laundry, noise and vibration problems may occur in the machine.

USING DETERGENT AND SOFTENER

When using detergent, softener, starch, fabric dye, bleach or limescale remover read the manufacturer’s instructions on the package carefully and follow the suggested dosage values. Use a measuring cup if available.

DETERGENT DRAWER
The detergent drawer is composed of three compartments:

For prewash
For main wash
For softener
- In addition, there is a siphon piece in the softener compartment.

DETERGENT, SOFTENER AND OTHER CLEANING AGENTS

Add detergent and softener before starting the washing program.
Never leave the detergent drawer open while the washing program is running!
When using a program without prewash, do not put any detergent into the prewash compartment (compartment nr. “1”).
In a program with prewash, do not put liquid detergent into the prewash compartment (compartment nr. “1”).
Do not select a program with prewash if you are using a detergent bag or dispensing ball. Place the detergent bag or the dispensing ball directly among the laundry in the machine.
If you are using liquid detergent, do not forget to place the liquid detergent cup into the main wash compartment (compartment nr. “2”).

CHOOSING THE DETERGENT TYPE
The type of detergent to be used depends on the type and colour of the fabric.

Use different detergents for coloured and white laundry.
Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.) used solely for delicate clothes.
When washing dark-coloured clothes and quilts, it is recommended to use liquid detergent.
Wash woollens with a special detergent made specifically for woollens.

WARNING : Use only detergents manufactured specifically for washing machines.

WARNING : Do not use soap powder.

ADJUSTING DETERGENT AMOUNT
The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and water hardness.

Do not use amounts exceeding the dosage quantities recommended on the detergent package to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.
Use less detergent for small amounts or lightly soiled clothes.

USING SOFTENERS

Pour the softener into the softener compartment of the detergent drawer.

Do not exceed the (>max<) level marking in the softener
If the softener has lost its fluidity, dilute it with water before putting it in the detergent

USING LIQUID DETERGENTS

IF THE PRODUCT CONTAINS A LIQUID DETERGENT CUP:

Make sure that you have placed the liquid detergent cup in compartment “2”.
If the liquid detergent has lost its fluidity, dilute it with water before putting it in the detergent

IF THE PRODUCT IS EQUIPPED WITH A LIQUID DETERGENT PART:

When you want to use liquid detergent, pull the drawer towards yourself. The part that falls will serve as a barrier for the liquid detergent. If required, clean the apparatus with water when it is in place or by removing it.
If you will use powder detergent, the apparatus must be secured at the top position.

IF THE PRODUCT DOES NOT CONTAIN A LIQUID DETERGENT CUP:

Do not use liquid detergent for the prewash in a program with prewash.
Liquid detergent stains your clothes when used with the Delayed Start function. If you are going to use the Delayed Start function, do not use liquid detergent.

USING GEL AND TABLET DETERGENT

Apply the following instructions when using tablets, gel and similar detergents.

If the gel detergent thickness is fluidal and your machine does not contain a special liquid detergent cup, put the gel detergent into the main wash detergent compartment during the first water intake. If your machine contains a liquid detergent cup, fill the detergent into this cup before starting the program.
If the gel detergent thickness is not fluid or in the shape of a capsule liquid tablet, put it directly into the drum before washing.
Put tablet detergents into the main wash compartment (compartment nr. “2”) or directly into the drum before washing.

Tablet detergents may leave residues in the detergent compartment. If you encounter such a case, place the tablet detergent between the laundry, and close to the lower part of the drum in future washings.

Use the tablet or gel detergent without selecting the prewash function.

USING STARCH

Add liquid starch, powder starch or the fabric dye into the softener
Do not use softener and starch together in a washing
Wipe the inside of the machine with a damp and clean cloth after using

USING BLEACHES

Select a program with prewash and add the bleaching agent at the beginning of the prewash. Do not put detergent in the prewash As an alternative application, select a program with extra rinse and add the bleaching agent while the machine is taking water from the detergent compartment during the first rinsing step.
Do not use bleaching agent and detergent by mixing
Use just a small amount (approx. 50 ml) of bleaching agent and rinse the clothes very well as it causes skin irritation. Do not pour the bleaching agent onto the clothes and do not use it for coloured clothes.
When using oxygen-based bleaches, select a program that washes at a lower
Oxygen-based bleaches can be used together with detergents; however, if its thickness is not the same as the detergent, put the detergent first into compartment “2” in the detergent drawer and wait until the detergent flows while the machine is taking in water. Add the bleaching agent from the same compartment while the machine is still taking in water.

USING LIMESCALE REMOVER

When required, use limescale removers manufactured specifically for washing machines only.

TIPS FOR EFFICIENT WASHING

DETERGENT RECOMMENDATION JOCEL-JLR014092-Washing-Machine-FIG-
20

Agglomerating or ropy detergent or additive can be diluted in some water detergent dispensers, to avoid its inlet getting blocked before pouring it into the thus causing a water overflow.
Please choose the suitable type of detergent to get a maximum washing performance and a minimum water and energy consumption
To achieve the best cleaning result a proper detergent dosing is
Use a reduced detergent amount if the drum is not filled
Always adjust the amount of detergent to the water’s hardness, if your tap water is soft, use less
Dose according to how dirty your laundry is, less dirty clothes require less
Highly concentrated (compact detergent) requires particularly accurate

The following symptoms are a sign of detergent overdosing:

Heavy foam formation.
Poor washing and rinsing result.

The following symptoms are a sign of detergent underdosing:

The laundry turns grey.
Built-up of limescale deposits on the drum, the heating element and/or the laundry.

OPERATING THE PRODUCT

CONTROL PANEL

$JOCEL-JLR014092-Washing-Machine-FIG- $10$$

Program Selection knob (On / Off)
Display
AI-Wash button
Program Follow-up indicator
Start / Pause button
Auxiliary Function buttons
Spin Speed Adjustment button
Temperature Adjustment button

PREPARING THE MACHINE
Make sure that the hoses are connected tightly. Plug in your machine. Turn the tap on completely. Place the laundry in the machine. Add detergent and fabric softener.

PROGRAMME SELECTION

Select the program suitable for the type, quantity and soiling degree of the laundry by the “Program and consumption table” and the temperature table below.
90º C| Heavily soiled white cottons and linens. (coffee table covers, tablecloths, towels, bed sheets, etc.)
---|---
60º C| Normally soiled, coloured, fade-proof linens, cottons or synthetic clothes (shirt, nightgown, pyjamas, etc.) and lightly soiled white linens (underwear, etc.)
40º C-

30º C-

20º C-

Frio

| Blended laundry including delicate textiles (veil curtains, etc.), synthetics and woollens.
2. Select the desired program with the Program Selection button.

Programs are limited to the highest spin speed appropriate for that particular type of fabric. When selecting a program, always consider the type of fabric, colour, degree of soiling and permissible water temperature. Always select the lowest required temperature. Higher temperature means higher power consumption. For further program details, see the “Program and consumption table”.

PROGRAM INTRODUCTION

Depending on the type of fabric, use the following main programs.

Cotton
Use this program for your cotton laundry (such as bed sheets, duvet and pillowcase sets, towels, bathrobes, underwear, etc.). Your laundry will be washed with vigorous washing action for a longer washing cycle.

Down Wear
The process of downwear is specially designed for washing down jackets. The material of the down jacket is light, difficult to rinse, has poor anti- washing ability, and difficult to absorb water. Therefore, it is necessary to extend the soaking time in the washing process and reduce the rotation speed during dehydration.

Woolen
Use this program to wash your woollen clothes. Select the appropriate temperature complying with the tags of your clothes. Use appropriate detergents for woollens.

Bedding
The main washing objects of the program are bed sheets, quilt covers, curtains, overcoats and tablecloths. In the washing process, the soaking time and washing time of the load are increased to improve the washing effect.

Drum Clean
Periodically (every 1 2 months) use this program to clean the drum for necessary sanitation cleaning. Let the washing machine run the program without any laundry. For better results, add powdered limescale cleaning agent to the detergent box. After the program, leave the front door ajar and let the inside of the machine dry.

Stain
For clothes with more stubborn stains, the washing effect can be improved by longer washing times and a strong washing rhythm.

Underwear
The underwear program is a special program for washing g underwear and other close-fitting clothes. The washing rhythm is weak. At the same time, to ensure the rinsing performance and prevent detergent residue, the rinsing intensity is required to be higher.

Silk
You can choose this program to wash delicate fabrics such as silk. The wash is very gentle, and the spin step is not done right away. This program is best if the laundry requires a gentle wash.

Steam
The steam washing process produces steam in the washing process, improve the washing effect, and at the same time, steam iron the clothes to prevent wrinkles.

Quick 15’
Quick Wash 15 is a fast-washing program for a small amount of non-dirty clothes. Its optional washing temperature range is narrow and the maximum speed of dehydration is low.

Mix
Use this program to wash your cotton and synthetic clothes together without sorting them.

20ºC
A new European standard special program is used to wash some mild clothes, the temperature can only be selected at 20 ℃, to protect the clothes.

ECO 40-60
For washing cotton garments that are normally washable at 40°C or 60°C, while washing in the same cycle. This cycle is used to assess compliance with EU eco-design regulations.

SPECIAL PROGRAMMES
For specific applications, select any of the following programs.

Rinse + Spin
A program designed for users to rinse and dehydrate.

Spin
Use this program to apply an additional spin cycle for your laundry or to drain the water in the machine. Before selecting this program, select the desired spin speed and press Start / Pause button. First, the machine will drain the water inside of it. Then, it will spin the laundry with the set spin speed and drain the water coming out of it. If you wish to drain only the water without spinning your laundry, select the Pump+Spin program and then select the No Spin function with the help of the Spin Speed Adjustment button. Press the Start / Pause button

TEMPERATURE SELECTION

Whenever a new program is selected, the default temperature of the selected program is displayed in the temperature indicator. To adjust the temperature, press the temperature button. The temperature will gradually increase and cycle to the lowest when the maximum is reached.

If the program has not reached the heating step, you can change the temperature without switching the machine to Pause mode.

SPIN SPEED SELECTION
Whenever a new program is selected, the default dehydration speed of the selected program is displayed on the speed indicator. To adjust the dehydration speed, press the speed button. The rotation speed increases gradually and circulates to the lowest when it reaches the highest.

PROGRAMME AND CONSUMPTION TABLE

Selectable
Automatically selected, no cancelling.

Energy test program: ECO 40-60. Set as default without selection.
The most efficient programs in terms of energy consumption are generally those that perform at lower temperatures and longer duration.
Noise and remaining moisture content are influenced by the spinning speed: the higher the spinning speed in the spinning phase, the higher the noise and the lower the remaining moisture content.
For more data information, please scan the QR code on the energy label.

AUXILIARY FUNCTION SELECTION

Wash +
In the standby mode, press the enhanced washing function setting button, the Strengthen washing function indicator will be on, and the Strengthen washing function will be added to the washing process. After selecting the Strengthen washing function, the washing time in the main washing stage will be increased by 10 minutes, and the time after adding the Strengthen washing function will be displayed in the remaining time window. If you press it again, the Strengthen washing function will be cancelled.

Rinse +
Press the rinse Plus button in standby mode, and the rinse Plus function indicator will be on. At the same time, add a rinse process in the washing process, and the time after adding the function will be displayed in the remaining time window. The rinse function will be cancelled when it is pressed again, if it does not run to the rinse stage during operation, press the pause button, The rinsing button can be added or cancelled, and the rinsing function cannot be selected or cancelled during operation

Smart Start
The smart start program is an intelligent program, which can be entered and run automatically in the standby and power off states. Under the smart start program, the washing temperature, water level and washing time are automatically set according to the weighing results, and the washing parameters do not need to be set by the user.

Delay
With the Delayed Start function, the startup of the program may be delayed up to 24 hours. Delayed start time can be increased by increments of 1 hour

Do not use liquid detergents when you set Delayed Start! There is the risk of staining of the clothes Additional laundry may be loaded during the delayed start period.

Open the loading door, place the laundry put detergent, etc. Select the washing program, temperature, spin speed and, if required, the auxiliary functions. Set the desired time by pressing the Delay button. Press the Start / Pause button. The delayed start time you have set is displayed. The delayed start countdown starts. The “_” symbol next to the delayed start time moves up and down on the display

At the end of the countdown, the duration of the selected program will be displayed. The “_” symbol will disappear and the selected program will start.

CANCELING THE DELAYED START FUNCTION
At the end of the countdown, the duration of the selected program will be displayed. The “_” symbol will disappear and the selected program will start.

STARTING THE PROGRAMME
Press the Start / Pause button to start the program. The program follow-up light showing the startup of the program will turn on.

If no program is started or no key is pressed within 10 minutes during the program selection process, the machine will switch to turn-off mode and the temperature, speed and other lights will turn off.

CHILD LOCK
Use the Child Lock function to prevent children from tampering with the machine. Thus, you can avoid any changes in a running program.

If the Program Selection knob is turned when the Child Lock is active, “CL” appears on the display. The Child Lock does not allow any change in the programs and the selected temperature, speed and auxiliary functions. Even if another program is selected with the Program Selection knob while the Child Lock is active, the previously selected program will continue running.

TO ACTIVATE THE CHILD LOCK:
Press and hold the 1st and 2nd Auxiliary Function buttons for 3 seconds while any program is running. The Child Lock is activated. If you press any button or turn the Program Selection knob when the Child Lock is active, “CL” will appear on the display and blink 3 times.

TO DEACTIVATE THE CHILD LOCK:
Press and hold the 1s t and 2nd auxiliary function buttons for 3 seconds while any program is running. The Child Lock is deactivated.

In addition to the method above, to deactivate the Child Lock, switch the Program Selection knob to the On/Off position when no program is running, and select another program. Child Lock is not deactivated after power failures or when the machine is unplugged

PROGRESS OF PROGRAMME
The progress of a running program can be followed by the Program Follow-up indicator. At the beginning of every program step, the relevant indicator light will turn on and the light of the completed step will turn off. You can change the auxiliary functions, speed and temperature settings without stopping the program flow while the program is running. To do this, the change you are going to make must be in a step after the running program step. If the change is not compatible, relevant lights will flash 3 times.

If the machine does not pass to the spinning step, the Rinse Hold function might be active or the automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the machine.

LOADING DOOR LOCK ”
There is a locking system on the loading door of the machine that prevents the opening of the door in cases when the water level is unsuitable. The loading door light will start flashing when the machine is switched to Pause mode. The machine checks the level of the water inside. If the level is suitable, the Loading Door light illuminates steadily within 1- 2 minutes and the loading door can be opened. If the level is unsuitable, the Loading Door light turns off and the loading door cannot be opened. If you are obliged to open the Loading Door while the Loading Door light is off, you have to cancel the current program; see “Canceling the program

CHANGING THE SELECTIONS AFTER PROGRAM HAS STARTED SWITCHING THE MACHINE TO PAUSE MODE
Press the Start / Pause button to switch the machine to pause mode while a program is running. The light of the step which the machine is in starts flashing in the Program Follow-up indicator to show that the machine has been switched to the pause mode. Also, when the loading door is ready to be opened, the Loading Door light will illuminate continuously in addition to the program step light.

CHANGING THE SPEED AND TEMPERATURE SETTINGS FOR AUXILIARY FUNCTIONS
Depending on the step the program has reached, you may cancel or activate the auxiliary functions; see, “Auxiliary function selection”. You may also change the speed and temperature settings; see, “Spin speed selection” and “Temperature selection”.

If no change is allowed, the relevant light will flash 3 times. ADDING

ADDING OR TAKING OUT LAUNDRY
Press the Start / Pause button to switch the machine to pause mode. The program follow-up light of the relevant step during which the machine was switched into the pause mode will flash. Wait until the Loading Door can be opened. Open the Loading Door and add or take out the laundry. Close the Loading Door. Make changes in auxiliary functions, temperature and speed settings if necessary. Press the Start / Pause button to start the machine

CANCELING THE PROGRAMME
To cancel the program, turn the Program Selection knob to select another program. The previous program will be cancelled. The end / Cancel light will flash continuously to notify that the program has been cancelled. The pump function is activated for 1-2 minutes regardless of the program step, and whether there is water in the machine or not. After this period, your machine will be ready to start with the first step of the new program.

Depending on the step where the program was cancelled, you may have to put detergent and softener again for the program you have selected anew.

END OF PROGRAMME
End” appears on the display at the end of the program. Wait until the loading door light illuminates steadily. Press the On / Off button to switch off the machine. Take out your laundry and close the loading door. Your machine is ready for the next washing cycle

MAINTENANCE AND CLEANING

The service life of the product extends and frequently faced problems decrease if cleaned at regular intervals

CLEANING THE DETERGENT DRAWER
Clean the detergent drawer at regular intervals (every 4-5 washing cycles) as shown below to prevent accumulation of powder detergent in time.

If more than the normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned.

Lift the rear part of the siphon to remove it as illustrated. After performing the above-mentioned cleaning procedures, replace the siphon with its seating and push its front section downwards to make sure that the locking tab engages.

CLEANING THE LOADING DOOR AND THE DRUM
For products with drum cleaning programs, please see Operating the Product Programs.

For products without drum cleaning, follow the below steps to clean the drum:

Select Additional Water or Extra Rinse auxiliary functions. Use a Cottons program without pre-wash.
Set the temperature to the level recommended by the drum cleaning agent which can be provided by authorized services. Apply this procedure without any laundry in the product. Before starting the program, put 1 pouch of special drum cleaning agent (if the special agent could not be supplied, put max. 100 g of powder anti-limescale) into the main wash detergent compartment (compartment no. “2”). If the anti-limescale is in tablet form, put only one tablet into the main wash compartment no. “2”.
Dry the inside of the bellow with a clean piece of cloth after the program has come to an end.

Repeat the Drum Cleaning process every 2 months. Use an anti-limescale suitable for the washing machines.

After every washing make sure that no foreign substance is left in the drum.

If the holes below shown in the figure are blocked, open the holes using a toothpick.

Foreign metal substances will cause rust stains in the drum. Clean the stains on the drum surface by using cleaning agents for stainless steel. Never use steel wool or wire wool.

WARNING : Never use sponge or scrub materials. These will damage the painted and plastic surfaces.

CLEANING THE BODY AND CONTROL PANEL

Wipe the body of the machine with soapy water or non-corrosive mild gel detergents as necessary, and dry with a soft cloth.
Use only a soft and damp cloth to clean the control panel

CLEANING THE WATER INTAKE FILTERS
There is a filter at the end of each water intake valve at the rear of the machine and also at the end of each water intake hose where they are connected to the tap. These filters prevent foreign substances and dirt in the water from entering the washing machine. Filters should be cleaned as they do get dirty.

Close the taps.
Remove the nuts of the water intake hoses to access the filters on the water intake Clean them with an appropriate brush. If the filters are too dirty, take them out using pliers and clean them.
Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under running water.
Replace the gaskets and filters carefully in their places and tighten the hose nuts by running water.

DRAINING REMAINING WATER AND CLEANING THE PUMP FILTER
The filter system in your machine prevents solid items such as buttons, coins and fabric fibres from clogging the pump impeller during the discharge of washing water. Thus, the water will be discharged without any problem and the service life of the pump will extend. If the machine fails to drain water, the pump filter is clogged. The filter must be cleaned whenever it is clogged or every 3 months. Water must be drained off first to clean the pump filter.

In addition, before transporting the machine (e.g., when moving to another house) and in case of freezing of the water, water may have to be drained completely.

WARNING: Foreign substances left in the pump filter may damage your machine or may cause noise problems.

To clean the dirty filter and discharge the water:

Unplug the machine to cut off the supply power.
WARNING: The temperature of the water inside the machine may rise to 90 ºC. To avoid burning risk, the filter must be cleaned after the water in the machine cools down.
Open the filter cap.
You can remove the filter cover by slightly pushing downwards with a thin plastic-tipped tool, through the gap above the filter cover. Do not use metal- tipped tools to
remove the cover.
Some of our products have an emergency draining hose and some do not. Follow the steps below to discharge the water. Discharging the water when the product does not have an emergency draining hose: $JOCEL-JLR014092-Washing-Machine-FIG- $16$$
- Place a large container in front of the filter to catch water from the filter.
- Loosen the pump filter (anticlockwise) until water starts to flow. Fill the flowing water into the container you have placed in front of the filter. Always keep a piece of cloth handy to absorb any spilt water.
- When the water inside the machine is finished, take out the filter completely by turning it.
Clean any residues inside the filter as well as fibres, if any, around the pump impeller region.
Install the filter.
If the filter cap is composed of two pieces, close the filter cap by pressing on the tab. If it is one piece, place the tabs in the lower part into their places first, and then press the upper part to close.

REGULAR CLEANING
Clean the interior of the pump housing, removing any debris or foreign objects, periodic cleaning, including optimal frequency, and limescale prevention and procedure. If the appliance water supply slows or stops completely, the water inlet strainer may be blocked. Cleaning is recommended every 6 months in any event to reduce chances of valve blockage in areas using hard water.

TECHNICAL SPECIFICATIONS|
---|---
Model name| JLR014092
Capacity (kg)| 6
Maximum spin speed (rpm)| 1000
Height (cm)| 84
Width (cm)| 60
Depth (cm)| 45
Net weight (±4 kg.)| 53
Input (V/Hz) Total| 220-240V~50Hz

PROGRAMMES

The above data is for reference only, and the data may change due to different actual use conditions.
The valves given for programs other than the ECO 40-60 program are indicative only.

TROUBLESHOOTING

PROGRAM DOES NOT START AFTER CLOSING THE DOOR

Start/Pause/Cancel button was not >>> *Press the Start/Pause/Cancel button.

PROGRAMME CAN NOT BE STARTED OR SELECTED

The washing machine has switched to self-protection mode due to a supply problem (line voltage, water pressure, etc.). >>> To cancel the program, turn the Program Selection knob to select another program. The previous program will be cancelled. (See “Canceling the program”).

WATER IN THE MACHINE

Some water might have remained in the product due to the quality control processes in the production. >>> This is not a failure; water is not harmful to the machine.

MACHINE VIBRATES OR MAKES NOISE

The machine might be standing >>> Adjust the feet to level the machine.
A hard substance might have entered into the pump >>> Clean the pump filter.
Transportation safety bolts are not >>> Remove the transportation safety bolts.
Laundry quantity in the machine might be too >>> Add more laundry to the machine.
The machine might be overloaded with laundry. >>> Take out some of the laundry from the machine or distribute the load by hand to balance it homogenously in the machine
The machine might be leaning on a rigid item. >>> Make sure that the machine is not leaning on

MACHINE STOPPED SHORTLY AFTER THE PROGRAMME STARTED.

The machine might have stopped temporarily due to low voltage. >>> It will resume running when the voltage restores to the normal level.

PROGRAMME TIME DOES NOT COUNTDOWN. (ON MODELS WITH DISPLAY)

The timer may stop during water intake. >>> The timer indicator will not countdown until the machine takes in an adequate amount of The machine will wait until there is a sufficient amount of water to avoid poor washing results due to lack of water. The timer indicator will resume the countdown after this.
The timer may stop during the heating step. >>> The timer indicator will not countdown until the machine reaches the selected temperature.
The timer may stop during the spinning step. >>> An automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum.
The machine does not switch to a spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and its surrounding environment. The laundry should be rearranged and re-spuned.

THE FOAM IS OVERFLOWING FROM THE DETERGENT DRAWER.

Too much detergent is used. >>> Mix 1 tablespoonful softener and ½ l water and pour into the main wash compartment of the detergent drawer.
Put detergent into the machine suitable for the programs and maximum loads indicated in the “Program and consumption table”. When you use additional chemicals (stain removers, bleachs etc.), reduce the amount of detergent.

LAUNDRY REMAINS WET AT THE END OF THE PROGRAMME

Excessive foam might have occurred and an automatic foam absorption system might have been activated due to too much detergent usage.
Use the recommended amount of detergent.
The machine does not switch to a spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and its surrounding environment. The laundry should be rearranged and re-spuned.

WARNING : If you cannot eliminate the problem although you follow the instructions in this section, consult your dealer or the Authorized Service Agent. Never try to repair a nonfunctional product yourself.

CUSTOMER SERVICE
Spare parts for your appliance are available for a minimum of 10 years. In case of questions please contact our customer service at:

WARNING : Risk of electric shock

Never try to repair an appliance which is defective or presumed to be defective. You may put your own and future users’ lives in danger. Only authorized specialists are allowed to carry out this repair work.
Improper repair will void the warranty and subsequent damages can’t be recognized!

GENERAL WARRANTY TERMS

The warranty is valid only on the presentation of the invoice of
This WARRANTY is limited exclusively to parts substitution ineffective due to faulty manufacture, made in our workshops.
The elimination of several faults in the scope of the guarantee is made for the repair or replacement of defective parts, according to the discretion of our technical Defective parts are our property.
Are not covered under warranty damage caused by transportation, neglect or poor use, improper assembly or installation, as well as external influences such as lightning strikes or power, flooding, humidity, etc.
Lose warranty, all appliances that are not being used according to the instructions or connected to FEEDING NETWORKS do not guarantee a constant voltage of 220/240V.
The warranty does not cover damages for personal injury or damage caused directly or indirectly in any capacity whatsoever.
This warranty terminates when it is found to have been undergoing repairs, alterations or interventions by any person not authorized by Jocel.

THE WARRANTY EXPIRES

If the appliance has not been installed by an Accredited
Exceeded the period for home appliances and industrial appliances, the warranty expires and assistance will be made by charging the costs of manpower, according to current fees.
With the modification or disappearance of the nameplate of the

NOTE: GLASSES AND LAMPS ARE NOT COVERED BY WARRANT.

TECHNICAL ASSISTANCE
For technical assistance requests, our services are available through the following contacts: Telef. 00 351 252 910351