SEALEY AK396.V4 Blind Nut and Stud Riveting Kit Instruction Manual
- June 13, 2024
- SEALEY
Table of Contents
BLIND NUT & STUD RIVETING KIT
MODEL NO: AK396.V4
AK396.V4 Blind Nut and Stud Riveting Kit
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR
THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE
FOR FUTURE USE.
Refer to instructions
Wear eye protection
SAFETY
‰ WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
√ Familiarise yourself with the application and the limitations of the
riveter, as well as the potential hazards.
√ Maintain the riveter in good condition (use an authorised service agent).
√ Replace or repair damaged parts. Use genuine parts only. Unauthorised parts
may be dangerous and will invalidate the warranty.
√Keep the work area clean, uncluttered and ensure there is adequate lighting.
√ Keep the riveter clean for best and safest performance.
√ Check moving parts alignment on a regular basis.
x DO NOT hold the workpiece by hand. Secure unstable workpiece with a clamp,
vice or other adequate holding device.
√ Ensure the workpiece is correctly secured before using the riveter.
x DO NOT use the riveter for any purpose other than that it was designed for.
x DO NOT operate the riveter if any parts are damaged or missing, as this may
cause failure and/or personal injury.
√ When not in use store in a safe, dry, childproof location.
INTRODUCTION
Suitable for blind rivets, rivet nuts and rivet studs in aluminium, steel and
stainless steel. 360° Swivel head gives greatly improved accessibility.
Four nozzles for blind rivets, four mandrels for rivet nuts and three mandrels
for rivet studs. Supplied with spanners and a selection of steel rivet nuts.
SPECIFICATION
Model no.: …………………………………………………….AK396.V4
Contents:
Blind Rivet Nozzle Sizes:
2.4(3/32”), 3.2(1/8”), 4(5/32”), 4.8mm(3/16”)
Rivet Nut Sizes: M3 x 0.5, M4 x 0.7, M5 x 0.8, M6 x 1mm
Rivet Stud Sizes: M4 x 0.7, M5 x 0.8, M6 x 1mm
Rivet Materials:
Aluminium, Steel, Stainless Steel
Rivets Nuts Supplied:M3 x 0.5, M4 x 0.7, M5 x 0.8, M6 x 1mm (10pc each)
CONTENTS
SET UP
Numbers refer to attached Parts List
5.1. RIVETING (fig.1)
5.1.1. Screw jaws and sleeve into body, select appropriate size of nosepiece
to match rivet. 
5.2. RIVET NUT (fig.2) (fig.2.A
for operation)
5.2.1. Push appropriate size of rivet nut rod (M3 – M6) into back of body.
5.2.2. Slide sleeve over pull rod and fit sleeve nut.
5.2.3. Note left-hand thread.
5.2.4. OPERATION
NOTE: Always use sleeve and rod of the same size, determined by the size of
nut rivet. 5.2.4.1. Prepare a sample of the workpiece material with a hole
slightly larger than the nut rivet diameter.
5.2.4.2. Screw the nut rivet fully onto the rod.
5.2.4.3. Place the nut rivet in the hole in the sample and press down so that
the nut flange is held firmly against the face of the sample.
5.2.4.4. Squeeze the riveter handles to compress the nut rivet.
5.2.4.5. The rivet will form a retaining bulge against the rear face of the
sample.
5.2.4.6. Unscrew the rod from the rivet nut rivet by turning the knurled end
of the draw bar body.
5.3. RIVET STUD (fig.3)
5.3.1. Push turnable bar (35) into back of body.
5.3.2. Screw riveting rod (32/33/34) onto turnable bar (35). Note: reverse
thread.
5.3.3. Screw fixing nut sleeve and adjusting nut (45 & 49) onto body.
5.3.4. Screw nut guide (46/47/48) onto fixing sleeve and adjusting nut
assembly (45 & 49).
5.3.5. OPERATION
5.3.5.1. Follow same procedure for Rivet nut Operation above.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note : It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk
or 01284 757505.
Important : No Liability is accepted for incorrect use of this product.
Warranty : Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
AK396.V4 Issue 1 03/10/22
Documents / Resources
|
SEALEY AK396.V4 Blind Nut and Stud Riveting
Kit
[pdf] Instruction Manual
AK396.V4, AK396.V4 Blind Nut and Stud Riveting Kit, Blind Nut and Stud
Riveting Kit, Nut and Stud Riveting Kit, Stud Riveting Kit, Riveting Kit, Kit
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>