Tokyo Communication Equipment PC-1620001 4ch RFID R and W Module User Manual
- June 13, 2024
- Tokyo Communication Equipment
Table of Contents
Tokyo Communication Equipment PC-1620001 4ch RFID R and W Module User
Manual
Scope
This product is the 4ch multi-channel 13.56MHz RFID R/W module. It supports the ISO/IEC15693.
- Product name :4ch RFID R/W Module
- Model name :PC-1620001 PC-1040021
Main specification
| Item | Function |
|---|---|
| RFID Tag | ISO/IEC15693 |
| Operation Voltage | DC5V |
| Communication Frequency | 13.56MHz ±7KHz |
| Type of Modulation | ASK |
| Output Power | 6.4dBm ±0.5dB (Burst Average) |
| I/F | Data Length 8bit、StopBit:1bit、Parity: NONE error correction: |
BCC38400bps(±3%)
Communication Range *****| 25mm(With RFID Tag：RI-I03-112A-03HA)
Dimmension| PC-1620001 50mm x 40mm
PC-1040021 52.5mm×15mm
RF Connection| 300ｍｍ Ｔｗｉｓｔｅｄ Ｐａｉｒ Ｃａｂｌｅ with Ferrite
core(3A4-TRB-16×10×10/Tomita）
- It depends on the surround environment.
Supports Legal Regulation
This product complies with the regulations of the Radio Law of the United States and Canada
(FCC, ISED) and is certified.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines as this equipment has very low levels of RF energy.
- CAN ICES-3 (B)/NMB-3(B)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules as this equipment has very low levels of RF energy.
General
This user manual describes the integration procedure per Sec. 2.2 to 2.12 of
KDB 996369 D03.
List of applicable FCC rules
This device complies with below part 15 of the FCC Rules.
Part 15 Subpart C
Summarize the specific operational use conditions
Not applicable.
Limited module procedures
Not applicable.
Trace antenna designs
Fine tuning of return loss etc. can be performed using a matching network.
However, it is required to check “Class1 change” and “Class2 change” which the
authorities define then.
RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines.
Antennas
The device is designed to use the antennas listed below. Do not modify the
antenna or any other part of the module. Any modifications will invalidate the
modular certifications and require new approvals for the host system.
Antenna No is PC-1040021, it is a printed magnetic loop type. Gain is -66.3dBi
Wire harness for Antenna with Ferrite core is defined below. (Changes are
prohibited.)
[2.8 Label and compliance information] Following information must be indicated
on the host device of this module.
Contains Transmitter Module FCC ID: 2ACJJPC1620001
Contains Transmitter Module IC : 11913A-PC1620001 [2.9 Information on test
modes and additional testing requirements] Test modes should take into
consideration different operational conditions for a stand-alone modular
transmitter in a host, as well as for multiple simultaneously transmitting
modules or other transmitters in a
host product.
Additional testing, Part 15 Subpart B disclaimer
The modular transmitter is only FCC authorized for the specific rule parts
(i.e., FCC transmitter rules) listed on the grant (FCC Part 15.225), and the
host product manufacturer is responsible for compliance to any other FCC rules
that apply to the host not covered by the modular transmitter grant of
certification.
The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
Note EMI Considerations
We recommend to use “best practice” RF design engineering testing and
evaluation in case non-linear interactions generate additional non-compliant
limits due to module placement to host components or properties. The host
manufacturer is responsible for ensuring compliance with the applicable FCC
rules for the transmitters operating individually and simultaneously. This
includes compliance for the summation of all emissions from all outputs
occupying the same or overlapping frequency ranges, as defined by the
applicable rules.
How to make changes
Only the grantee is permitted to make permissive changes.
Please contact us at Tokyo Communication Equipment Manufacturing Co., Ltd.
(Web) http://www.totsuki.co.jp/
(Mailform) http://www.totsuki.co.jp/support/inquiry.php
System Configuration
4ch RFID R/W Module (PC-1620001/PC-1040021) Block diagram
Just one output channel at the same time
Connections
[PC-1620001】
CN2：SM04B-ZESS-TB／JST
| No | Name | Memo |
|---|---|---|
| 1 | VIN | Power（＋）5V |
| 2 | GND | Power（－）0V |
| 3 | RXD | Receive 3.3V Level |
| 4 | TXD | Transmit 3.3V Level |
CN3-CN6：SM03B-SRSS-TB／JST
| No | Name | Memo |
|---|---|---|
| 1 | RF+ | Interconnected to the PC-1040021 |
| 2 | GND | |
| 3 | RF- |
[PC-1040021]
CN1：SM03B-SRSS-TB／JST
| No | Name | Memo |
|---|---|---|
| 1 | RF+ | Interconnected to the PC-1620001 |
| 2 | GND | |
| 3 | RF- |
Electrical Characteristics
Absolute Maximum Rating
| Item | Symbol | Rating | Unit | Memo |
|---|---|---|---|---|
| Input Power | VIN | 5.5 | V | |
| OperationTemperature | Topt | 10 ～ +50 | ℃ | |
| Operation Humidity | Hopt | 20 ～ 85 | %RH | No condensation |
Electrical Characteristics
| Item | Symbol | Condition | Rate | Unit |
|---|---|---|---|---|
| Min. | Typ. | Max. | ||
| Power | VIN | 4.8 | 5.0 | |
| Logic Power | VDD | – | 3.3 | |
| GND | GND | – | 0 | |
| Consumption Current | IDD | VIN = 5V | – | – |
Aspect (Unit：mm)
[PC-1620001】
t MAX 6ｍｍ
[PC-1040021]
Wire harness
Function Test
| Test Item | Content |
|---|---|
| Insulation Resistance | Over 10kΩ |
| Voltage | 3.3V±5％ |
| Writing Firmware | Success or failed |
| UART Communication Test | Success or failed |
| RFID Communication Test | 30mm Success or failed |
| 1～4ch Channel Test | 1～4ch RF switching test Success or failed |
Function test includes PC-1620001,PC-1040021 and connection harness.
Shipping
We pack it so that quality isn’t damaged during transportation.
Warranty
If any defect arises in the product mentioned in this document within six months after delivery, and Supplier is Assumed to be responsible for it, and such the product is undoubtedly out of specification, the product shall be returned and replaced with a new product or a re-tested product by Supplier at Supplier’s cost.
We do not assume any responsibility for the expenses of resulting damages caused from the under-mentioned cases even under warranty.
- Any defect and/or abrasion caused by force majeure such as natural hazard and abnormal voltage drop.
- Any defect and/or abrasion caused from displacement, drop, removal and/or transportation.
- Any modification or a party designated by Supplier.
- Improper handling, regardless intention or fault.
- Responsibility for over and short of final specification approved by customer.
- Any defect caused from aging such as degradation of painted surface and plated surface.
Revision History
| Date | Rev | Content |
|---|---|---|
| 2023/8/1 | 1.0 | 1’st |
TNS22275 Rev0.1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>