Soundingking KG06/08/10/12 Economical Mixer User Manual

Soundingking KG06/08/10/12 Economical Mixer

IMPORTANT SAFETY INSTRUCTIONS

• Read these instructions.

• Keep these instructions.

• Heed all warning.

• Follow all instructions.

• Water & Moisture
  The apparatus should be protected from moisture and rain, can not used near water, for example: near bathtub, kitchen sink or a swimming pool, etc.

• Heat
  The apparatus should be located away from the heat source such as radiators, stoves or other appliances that produce heat.

• Ventilation
  Do not block areas of ventilation opening. Failure to do could result in fire. Always install accordance with the manufacturer’s instructions.

• Object and Liquid Entry
  Objects do not fall into and liquids are not spilled into the inside of the apparatus for safety.

• Power Cord and Plug
  Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, refer to electrician for replacement.

• Power Supply
  The apparatus should be connected to the power supply only of the type as marked on the apparatus or described in the manual. Failure to do could result in damage to the product and possibly the user.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

• Fuse
  To prevent the risk of fire and damaging the unit, please use only of the recommended fuse type as described in the manual. Before replacing the fuse, make sure the unit turned off and disconnected from the AC outlet.

• Electrical Connection
  Improper electrical wiring may invalidate the product warranty.

• Cleaning
  Clean only with a dry cloth. Do not use any solvents such as benzol or alcohol.

• S ervicing
  Do not implement any servicing other than those means described in the manual. Refer all servicing to qualified service personnel only. Only use accessories/attachments or parts recommended by the manufacturer.

Introduction

Thank you for purchasing KG series compact mixer which features universal voltage 100-240V, compression function of each mic channel to keep crystal clear sound during performance. The mixer can play the music via SD card/USB/bluetooth. The mic sound or music of line in can be recorded to SD card/USB to suit for the requirement of solo or band performance or conference recording. KG series can also be connected with PC for playback and recording.

Application
suitable for the applications in PA system or indoor recording, e.g. Movie/TV/music recording in theatre/dancing hall/bar/conference hall, etc;

Function

1. 1-8 CH MIC/line and 2CH stereo inputs;
2. Compression function of mic channels (0-9dB);
3. Built-in USB/SD card/bluetooth playing/recording function;
4. 48V phantom power for condenser mic;
5. Built-in 16 program DSP with adjustable delay for wonderful effect;
6. Main outputs with 2X8 accurate meter to monitor output level;
7. Universal voltage 100V-240V;
8. MP3 interface can connect with PC for playback and recording;

A. Channel

1. Gain control
   It adjusts input signal level to balance the S/N ratio and dynamic range. To get best effect, adjust this knob: make PEAK LED flashes sometimes to avoid channel distortion.
   Mic input gain range : 6~50dB, line in gainrange: +10~ -34.

2. COMP
   It adjusts channel compression. Turn clockwise to increase compression ratio and gain will adjust automatically.

3. HPF
   It turns on/off the HPF with 18 dB octave to activate 80 Hz LF filter. You can also use it to reduce mains hum noise or stage mic noise.

4. EQ control
   Hi when you set it to max, 12KHz frequency level boosts +15dB. To min, and the 12KHz frequency levelcuts -15dB MID when you set it to max, 2.5KHz frequency level boosts +15dB. To min, and the 2.5KHz frequency level cuts -15dB. LOW when you set it to max, 45Hz frequency level boosts +15dB. To min, and the 45Hz frequency level cuts -15dB.

5. AUX-DSP
   These two knobs are used to the level of signal sent to AUX-DSP BUS, and then to external DSP, or to built-in DSP module. DSP knob can also adjust channel level.

6. PAN
   Set it to middle position, then sound image will be in the middle of the stage. It can also adjust the left/right output signal.

7. PEAK LED
   When signal reaches the level of clipping level deducted 3dB, PEAK LED lights up red.

8. MUTE & LED
   Each channel is designed with MUTE button. Press it to mute the channel. The mute LED lights up.

9. FADER
   It adjusts the level of channel signal which is sent to main mix out.
   Note : set the unused faders to minimum position.

Stereo channel

1. -10/+4 sensitivity switch
   Press t his switch, this sensitivity will be 10dB higher.

2. LINE/USB/MP3 selection switch
   Release for stereo line input. Press for USB/MP3/bluetooth input

3. EQ control
   Hi : set to maximum position, and 12KHz frequency level boosts +15dB. Set to minimum position, and 12KHz frequency level cuts -15dB.
   LOW : set to maximum position, and 60Hz frequency level boosts +15dB. Set to minimum position, and 60Hz frequency level cuts -15dB.

4. AUX-DSP
   These two knobs are used to the level of signal sent to AUX-DSP BUS, and then to external DSP, or to built-in DSP module. DSP knob can also adjust channel level.

5. PAN
   Set it to middle position, then sound image will be in the middle of the stage. It can also adjust the left/right output signal.

6. PEAK LED
   When signal reaches the level of clipping level deducted 3dB, PEAK LED lights up red.

7. MUTE BUTTON & MUTE LED
   Each channel is designed with MUTE button. Press it to mute the channel.The mute LED lights up.
   FADER
   It adjusts the channel level.
   Note : set the faders of unused channels to minimum position to reduce noise.

OUTPUT AND REAR PANEL

1. MIC/LINE CHANNEL (CH1-6)
   Balanced XLR input connector (1 ground 2 hot 3 cold).KG08 Is designed with 4 low noise mic pre-amp (KG06 has 2, KG10 has 6,KG12 has 8) and phantom power, 45dB gain and >100 dB S/N ratio. The phantom power is used for condenser mic. If you use dynamic mic,please turn off phantom power first. These channels are designed with 1/4inch TRS bal/unbal line in connectors to connect with keyboard, electric drum, DSP, etc.

2. Stereo channel input
   Unbalanced connectors. If signal input from LEFT/MONO, the signal outputs from L/R main mix outputs. If signal inputs from RIGHT connector, signal outputs from R main mix output. This connector can be connected with keyboard, electric drum, DSP, etc.

3. AUX SENDS
   1/4″ phone jacks to send signal from AUX BUS to external equipments, e.g. Effect equipment or stage monitor, etc;

4. DSP output
   1/4″ phone jack to output DSP signal and the level is controlled by channel DSP.

5. AUX RETURNS input
   Stereo 1/4″ phone jacks to return effect equipment stereo signal to Main Mix. Or you can Use AUX RETURN knob to adjust volume. The input AUX signal will be sent to MAIN MIX.

6. PLAYBACK
   Unbal RCA and 3.5 connectors to input signal from CD player/computer, etc;

7. RECORD
   Unbal RCA connector to output signal to recording equipment.

8. MAIN MIX output
   Bal XLR connector. The level is adjusted by Main Mix fader.

9. CTRL ROOM output
   1/4″ phone jacks send Control Room signal to monitor speaker cabinet.

10. POWER socket
    It is designed with fuse to connect with mains. Please replace the fuse with the same type and rating.

11. POWER swtich
    It turns on/off the mixer.

1. +48V phantom power switch/red when on
   It is used for condenser mic operation. Please set all faders to minimum before turning on the switch to protect speaker cabinets.

2. Stereo return
   It adjusts stereo return signal level.

3. AUX send
   It adjusts aux send level.

4. PLAYBACK
   It adjusts the playback signal level.

5. CTRLMP PHONES
   It adjusts the phone signal level.

6. PLAYBACK switch
   Press the switch to send signal to monitor and phones.

7. MAIN MIX switch
   Press the switch to send MAIN signal to monitor and phones.

8. Phone output
   This connector send signal to phones.

9. DSP ON switch
   Press this switch to start DSP operation and LED lights up green.

10. DSP fader
    It adjusts the DSP signal level.

11. PARAMETER
    It adjusts the delay time.

12. PROGRAM**
    Prg#| Description| Parameter 1**
    ---|---|---
    1| Small Hall| Rev Time| 0.9sec~3.5sec
    2| Large Hall| Rev Time| 1.5sec~8.6sec
    3| Small Room| Rev Time| 0.28sec~0.82sec
    4| Bright Room| Rev Time| 0.36sec~1.38sec
    5| Thin Plate| Rev Time| 0.44sec~1.54sec
    6| Large Plate| Rev Time| 0.72sec~10sec
    7| Spring Reverb| Rev Time| 0.4sec~2.3sec
    8| Multi-tap Delay| Delay Time| 0~680ms
    9| Analog Delay| Delay Time| 0~680ms
    10| Chorus Verb| Rev Time| 0.56sec~3.5sec
    11| STEREO CHORUS| Rate| 0.58Hz~6Hz
    12| Flanger| Rate| 0.58Hz~4.35Hz
    13| Phaser| Rate| 0.58Hz~11Hz
    14| Gated Reverb| Gate Time| 0.25sec~0.78sec
    15| Flange Verb| Rev Time| 0.34sec~2sec
    16| Vocal Echo| Delay Time| 0~400ms

13. POWER LED

14. PEAK LED

15. MAIN OUTPUT LEVEL LED

16. MAIN MIX fader
    It adjusts the MAIN MIX output level.

SD/USB/BLUETOOTH

1. MODE
   Press this button to select mode: SD card, USB, bluetooth, recording.

   • a) SD/USB mode: insert SD card/USB to play music directly.
   • b) Bluetooth mode press the button to select bluetooth, then match the bluetooth, then play music.
   • c) Recording mode press the button to select recording mode. Input signal from mic or line, then press play button to record. The LCD displays recording symbol flashing.

2. Play/pause button

3. Stop button

4. Repeat button

5. Previous button

6. Next button

7. Sd card connector for playback and recording

8. USB interface to connect with PC for playback and recording.

SD card/USB details

Loop Functions
1 = play one chosen track on loop (repeat) Note in this mode individual tracks cannot be selected.
F = play all tracks within same folder on your SD card or USB drive in sequence on loop (repeat).
R = shuffle – plays all tracks randomly no loop (no repeat)
A = plays all tracks in sequence on loop (repeat)

• Selecting and playing individual tracks from an USB or SD card.
• Press and hold the PLAY/PAUSE button.
• Use the forward/back buttons to select the required track.
• Release the PLAY/PAUSE button.
• Your selected track will now be cue’d and paused and will play when the PLAY/PAUSE button is pressed again.
• Useful tips for getting most out of your playback facility during a live performace :
• Record a track with no sound on it it, say 30 seconds long. Call this track ‘001 – Silence’ and make sure it’s always the first track in your file. The reason to do this, is to allow you sufficient time when inserting your memory stick to allow you to enter the play/pause track cueing facility without accidentally playing a track. You can then select the track want leaving the player in PAUSE ready for the performance.
• Add a few seconds (up to about 30 seconds) of no sound (quiet) to the end of all of your recorded tracks.
• The player will automatically play the next track in sequence if you have multiple tracks, so adding this quiet section to your tracks allows you time to stop your player and cue your next track, to avoid the player going into an unwanted track.

Installation

1. There should be no obstacles before the speaker cabinet. You had better put the speaker cabinet on a speaker stand.
2. Use professional devices to suspend or install the speaker cabinets to avoid hurt.
3. Use high quality cable to ensure the best tone.
4. Please match the right power and impedance of power amplifier and speaker cabinet.
5. Do not point the microphone to the speaker cabinet to avoid feedback.

Bal/unbal mode of TRS/XLR connectors

• 1/4 TRS or XLR connector bal/unbal modes; please refer to below:
• 1/4 connector

Connection
The supplied 1/4 TRS and XLR connector to connect with pro audio equipments; please refer to below:

BLOCK DIAGRAM

Specification

Mono input|
---|---
Mic input| Bal input|
Frequency response| 10 Hz to 30 kHz, +/-3 dB|
THD(THD&N)| 0.03% at +4 dBu, 22Hz-20kHz A-weighted|
Compression| GAIN:0-9dB,THRESHOLD: 20dB 5dB|
S/N ratio| (SNR)115 dB|
Line in| Bal input|
Frequency response| 10 Hz to 30kHz, +/-3 dB|
THD(THD&N)| 0.005% at+4 dBu, 22Hz-20kHz A-weightde|
Max gain| 75 dBu MIC INPUT MAIN OUTPUT|
Stereo input channel|
Line in| Bal/unbal|
Frequency response| 10 Hz to 55 kHz, +/-3 dB|
THD(THD&N)| 0.005% at +4 dBu, 22Hz-20kHz A-weighted|
Impedance|
Mic input| 1.4 kOhm|
Line in| 10 kOhm|
Other inputs| 10 kOhm or more|
Recording output| 1 kOhm|
Other outputs| 120 Ohm|
Mono EQ|
HI| +/-15 dB @12 kHz|
MID| +/-15 dB @2.5 kHz|
LOW| +/-15 dB @45 Hz|
Low cut filter| 80 Hz, 18 dB/Oct.|
****|
HI| +/-15 dB @12 kHz|
LOW| +/-15 dB @60 Hz|
DSP| A/D & D/A converter sample frequency 24-Bit  16 programs|
Main mix|
Noise (BUS noise)| Fader 0dB,all input channel knobs set to minimum, EQ knobs set to middle,:-100dBu(reference:+4dBu)|

Max output

|
Bal  +27dBu       unbal  +22dBu 1/4  connector|
AUX  +22 dBu|
 | DSP  +22dBu|
Power supply| 100-240 VAC~50/60 Hz|
Dimension(DWH)mm| KG06:330X224X92  KG08:330X280X92 KG10:330X336X92 KG12:330X392X92|
Net weight| KG06: 3.5KG  KG08: 4KG KG10: 4.5KG KG12: 5.2KG|

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>