FOXSKY 273551 24 Inch Premium HD LED TV Instructions

273551 24 Inch Premium HD LED TV
Instructions

Before using this TV please read the lnstrucnons and requests are properly preserved, to prepare for future needs

LED COLOR TV

1.41 Anti shell interface

listen to the sound from the TV on headphones.
*If you connect the earphones, the TV speakers will be muted.
2| AV IN 1| Connect to the video input jacks of a camcorder, video game and similar devices.
3| AV IN 2| Connect to the video input jacks of a camcorder, video game and similar devices.
4| HDMI Input Terminal| Connect this port to the HDMI output of AN device.
5| VGA signal input| Connect a 15-pin D-sub RGB cable to the RGB output of your computer and the other end to the RGB input on the rear of the LED TV.
6| PG Audio Input| Connect the Audio Out on your computer to the Audio on the rear of the LED TV
7| TV Input Jack (RF)| Connect this jack to your Cable or VHF/UHF antenna.
8| USB| Connect to your USB devices, such as USB flash drive.
| |

1.5 Remote Control

1. POWER BUTTON
   Switch OOl the LED whon at standby mode

2. PRE-CH BUTTON
   Pross tho butlon to togglo botwoon the curront anqtho provious program you woro viewing.

3. NUMBER BUTTONS
   Pross thoso buttons to soloct tho LED program yoy want lo onter or input password,

4. CH+/CH- BUTTON
   Pross two buttons to diroctly to adjust tho LED program.

5. VOL+/VOL-BUTTON
   Pross two buttons to directly to turn up or turn dowin tho sound volumo lovol.

6. MUTEBUTTON
   Pross the butlon lotum off the volumo. Pross it again to turn on the volume,

7. P.MODE BUTTON
   Picture effect seloction.

8. HDMI BUTTON
   Directly Into the HDMI mode.

9. CH.LIST BUTTON
   Displays channel list

10. MENU BUTTON
    Pross the butlon to cpen the main menu, pross agaln or use Exit to close.

11. OK BUTTON
    Press the butlon to confirm or ontor sub menus:

12. EXIT BUTTON
    Press the button o oxit.

13. UP, DOWN, LEFT, RIGHT ARROW BUTTONS
    Pross these bullons to select or adlust the dosired itom on the LED menu.

When selecting the signal source, the screen will display the information. When there is no signal from the selected source, the warning message will be Displayed as per illustration. Either change the channel in TV mode or press button to change source. 2.3 Menu Option Adjustment
After you have installed the batteries into the remote control, you will need to set some preferences on the LED TV, using the menu system.
– The buttons for menu option adjustment include Menu, B buttons.  buttons.
– Press the Menu button to open the OSD Menu, then press 4, button to select the pages, the pages are displayed in the following sequence (circular display): Note: “CHANNEL “ is only for TV,

1. Press the Menu button to display the menu system
2. Press button to select the menu pages.
1. Press , and the n press  button to select an item.
1. Press – button to selector adjust a setting.
1. If you do not make a selection within 10 seconds, the menu will close Automatically.
Press the Menu button to return or exit OSD menu.

Supported Signal Modes

A. VGA Mode

| Horizontal| Vertical
---|---|---
Resolution| Frequency| Frequency
| (KHz)| (Hz)
640 x 480| 31.50| 60.00
800 x 600| 35.| 56.25
37.90| 60.00
1024 x 768| 48.40| 60.00

Note: You re suggested to use the VGA connecting cord of not more than 5 meters to ensure the appropriate picture quality.
B. YPbPR Mode

60.00
1080P (1920×1080)| 56.25| 50.00

HDMI Mode

-When the signal received by the Display exceeds the allowed range, a warning message will appear on the screen.
– You can confirm the input signal format on screen.

Simple Troubleshooting

If the display fails or the performance changes dramatically, check the display in accordance with the following instructions. Remember to check the peripherals to pinpoint the source of the failure

ends of the power cable are plugged into the socket appropriately and the wall socket is operational
No Input Signal message appears.| -Check that the signal line is connected properly.
-Check that the power of the relevant peripherals is turned on. -Check that the Input option that has been selected matches with the input signal.
The remote control does not function properly.| -Check the batteries are not drained.(Use new batteries.)
-Check that the remote control is within the operating range.
-Check that the remote control is pointed to the remote control window on the display. -Check that there are no obstacles between the remote control and the remote control window
Flashing spots or stripes appear on the screen.| -Check that there are no emission (Car, I-1V cable or Neon lamp) or other possible interference sources.
Image colour or quality deteriorates.| -Check that all the video settings are adjusted appropriately, such as brightness, contrast, colour etc.
-For more information about video setting, refer to OSD Functions in Chaster 2.
Screen position and size are incorrect.| -Check that the screen position and size is adjusted appropriately.
Images or colour is incorrect.| -Check that the signal line is connected properly.
-When connecting to a PC, you can change the resolution of the PC to acquire the correct image. The discrepancy of the PC output signal may affect the display of the image.
Display warning message.| -Check that the input signal line is properly fixed.
-Select the correct input signal.
-For more information, refer to Supported Signal Modes in Chapter 4.

LED TV

Warranty Card

Dealer:……………………………………………
Customer’s Name:…………………………..
Address:………………………………………..
Tel #:…………………………………………….
Product:………………………………………..
Model:………………………………………….
Cash Memo:………………………………….
Date of Sale:………………………………….

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>