Ageislink S-WF240 Wi-Fi Smoke Alarm User Manual

Ageislink S-WF240 Wi-Fi Smoke Alarm

Thank you for purchasing this Wi-Fi smoke alarm. This user manual contains important information on installing and operating this smoke alarm. Please read this user manual before installation or operation, and save it for future reference.

Product Profile

Package Contents

• 1 x Alarm Unit
• 1 x Mounting Bracket
• 2xScrews
• 2 x Anchor Plugs
• 1 x User Manual
• 1 X Pin

Safety Information

Dangers, warnings, and cautions alert you to important installation and operating instructions, or potential hazards. Please pay attention to the situations.

IMPORTANT

1. THIS DEVICE IS NOT DESIGNED FOR HEARING-IMPAIRED PEOPLE. USE OF ALCOHOL OR DRUGS MAY IMPAIR ONE’S ABILfTYTO HEAR THE SMOKE ALARM.
2. FIRES IN CHIMNEYS, WALLS, ROOFS, OR BEHIND CLOSED DOORS MAY NOT BE DETECTED.
3. THIS DEVICE IS NOT INTENDED FOR DETECT NG FLAMES, HEAT, CARBON MONOXIDE, OR OTHER HAZARDOUS GASES.

WARNING

1. NEVER IGNORE AN ALARM. FAILURE TO RESPOND CAN RESULT IN SERIOUS INJURY OR EVEN DEATH.
2. THE SILENCE FEATURE IS ONLY FOR YOUR CONVENIENCE AND WILL NOT CORRECT A PROBLEM. ALWAYS CHECK YOUR HOME FOR ANY POTENTIAL HAZARDS EVERYTIME AN ALARM SOUNDS.
3. TESTTHIS SMOKE ALARM ONCE A WEEK. IF THE ALARM FAILS TO TEST CORRECTLY, REPLACE IT IMMEDIATELY! IF THE ALARM IS NOT WORKING PROPERLY, IT WILL NOT ALERT YOU TO A PROBLEM.

Set Up and Conned Smoke Alarms to Wi-Fi Before connecting smoke alarms, make sure that

1. Know your Wi-Fi network name and password.
2. Make sure you are connecting smoke alarms to a 2.4 GHz Wi-Fi network (incompatible with 5 GHz Wi-Fi network).
3. Make sure the Bluetooth on your phone is turned on.

NOTES

• Make sure you tum on some permissions in the mobile phone settings. Otherwise, the app cannot add devices or will fail to receive push notifications.
• re Some contents shown in the App user interface might slightly differ from those in the user manual due to later software upgrades.

How to connect

1. Before installing the alarm to a wall or ceiling, download the TuyaSmart/Smart Life app and connect the alarm to your Wi-Fi via the app. Search for TuyaSmart/Smart Life in the App Store or Google Play, or simply scan the included QR code to install the TuyaSmart/Smart Life app. You will also need to register an account. 

2. Remove the insulating film from the battery compartment to turn on the alarm. The LED indicator will flash red once, indicating that the smoke alarm has been activated. 

3. Open the TuyaSmart/Smart Life app, tap the•+• icon in the top right corner of the “Home” page, or directly tap “Add Device” to add your first device.

4. After you go to the “Add Device” page, a reminder “Searching for nearby devices” appears. Use a pin to press and hold the pairing button on the back of the device for 3 seconds. After the device beeps once, the LED indicator will flash green rapidly, indicating that the device has entered pairing mode. 

5. After the device enters pairing mode, it will begin searching and ‘Discovering devices• will appear on the ‘Add Device• page. Click “Add’ to add the device.

6. Click the”+” button next to the device, enter your Wi-Fi password, and make sure the entered Wi-Fi password is correct.
   NOTE : If you select “Done” without clicking “+”, you will be reminded to choose to odd o device in the opp. 

7. After the device is successfully added, select “Done.” The added device will now be displayed on the Home page in the app. NOTES

   • The LED indicator will flash green rapidly for up to 2 minutes during configuration. If connection is unsuccessful, the smoke alarm will need to be reconnected. Remove the battery for a short period and start again from step 2.
   • Unsuccessful connection may be because your router, mob/le phone, and alarm ore not as close to each other as possible, you have Jnco”ectly entered your WI-Fl password, or the Bluetooth on your phone Is not tumed on.

8. Once you have successfully connected your device to the app, you can continue to the “Settings” section to set up push notifications and change various settings for the app and device.
   NOTE : ff your home Wi-Fi router is a 2.4 and 5 GHz dual-band that works with a single SSID name,. please refer to your Wi-Fi router manual to create separate SSIDs for the 2.4 and 5 GHz channels. You can also select-Common router setting method” on the TuyaSmart/Smart Life App in the network configuration process to learn about the corresponding setting method.

App Settings

Notifications Settings

• Under Settings (the gear wheel on the unit’s home screen) you can adjust the type of notifications you want the smoke alarm to send. This can apply to both what is displayed on the screen and what is stored in the log.
• One thing to keep in mind is that if you turn on many notifications, it may seem as if the device “alerts” about something constantly. For example, if you turn on “Device Self-Check Notification”, you will receive a notification every time the unit performs a test after the test/silence button is pressed. The more information you activate, the more power the device will consume, as it creates more need for the device to transmit information, which means that the intervals for battery replacement will become shorter than the advertised one year.

Hlstorlcal Data (Log)
To access historical data or the log, click the “Click for more” button located at the bottom of the Home screen for the unit.

Offline Notification
The offline notification informs the user that the network is in an abnormal state. In order to ensure the device is working normally, you must check the state of the network. The device automatically reconnects to the Wi-Fi network every 8-12 hours. If the device tries to reconnect to the network 3 times but ultimately fails to reconnect, the status of the device is set to offline on the app page. At this time, an offline push notification is sent to the user’s cell phone via the app.

Note: The oftllne notification ls turned off by default. Nyou want to receive oftllne notllicatlons, you must tum on this feature.

Alarm Test

1. Always make sure to test your smoke alarm when it is turned on for the first time, or whenever you change the battery or reconfigure the device. You should also test the device weekly, or whenever you have been away from home for a long time.
2. Briefiy press the test/silence button. NOTE: if you hold down the button for more than three seconds, the smoke alarm will enter a reconnecting mode in the app and the previous settings will be cleared.
3. The unit beeps 3 times.
4. If your device has successfully connected to router, the LED indicator will fiash red and then fiash green rapidly for several seconds, indicating it has been connected.
5. When the test is finished, the alarm will automatically enter standby mode.

NOTES

1. The test function accurately tests the alarm’s smoke sensing drcult without the need to test with smoke. Hyoursmoke alarm falls to give an audible test signal, please refer Immediately to the troubleshooting guide at the end of this manual. Never use an open Rome to test this device.
2. If the LED Indicator flashes green for 2 minutes during the test, then the connection was not successful and the alarm needs to be reconnected (repeat the steps In the section -set Up and Connect Smoke Alarms to Wl-Fl-J,

Installation Positioning

NOTE: If a smoke alarm is installed in a kitchen, ensure this an easily accessible silence button and install the alarm as far away from the stove and sink as possible to avoid false alarms.

1. Prioritize the installation of an alarm in the bedroom and hallways, and make sure you can hear the alarm from all sleeping areas. In a home with several bedrooms, install an alarm in every bedroom. If you install only one smoke alarm in your home, install the alarm near to all bedrooms where possible, and not in a basement or furnace room.
2. Install an alarm above the stairway and on every floor of the house.
3. Smoke, heat and anything burning will spread horizontally after rising to the ceiling, so install the alarm in the middle of the ceiling where possible. Ensure that the alarm is installed at the minimum distance away from corner.
4. If an alarm cannot be installed in the middle of a ceiling, install it at a distance of 20 inches (50 cm) away from the corners of the room.
5. If an alarm is installed onto a wall, a distance of 4-12 inches (10-30 cm) should be kept below the ceiling.
6. If the length of a room or hallway is greater than 30 feet (900 cm), several alarms should be installed in the same room.
7. When the wall or ceiling is angled, the alarm needs to be installed within 3 feet (90 cm) of the highest wall or ceiling point (measured horizontally) in the room.
8. To maintain a secure and stable Wi-Fi connection, please be sure to install the alarm within the router’s coverage area and make sure that there are as few obstacles as possible between them.

WARNING

1. THIS ALARM SHOULD BE INSTALLED BY A COMPETENT PERSON.
2. ALARMS SHOULD NOT BE USED AS A SUBSTITUTE FOR PROPER INSTALLAllON, USE AND MAINllENANCE OF FUEL BURNING APPLIANCES INCLUDING APPROPRIATE VENllLATION AND EXHAUST SYSTEMS.
3. TO PREVENT INJURY, THIS DEVICE SHOULD BE SECURELY ATTACHED TO THE CEILING OR WALL IN ACCORDANCE WITH llHE INSTALLAllON INSTRUCTIONS.
4. BAffiRIES SHOULD NOT BE EXPOSED TO EXCESSIVE HEAT SUCH AS DIRECT SUNLIGHT, FIRE, ETC.

Installation Method

NOTE : Before Installation, we recommend you test the Wl?FI smoke alarms In the rooms you wish to install them In to ensure they are within range of the Wi?FJ router that nothing Is interfering with their communication.

1. Use the mounting bracket to mark the screw holes on the ceiling or the wall.
2. Drill holes at the two marks using an appropriately-sized drill bit. Insert the anchor plugs and screw the mounting bracket using the screws provided.
3. Attach the alarm to the mounting bracket and turn clockwise to lock the alarm.
4. Test the smoke alarm according to the steps in the section HAlarm TestH.

Silence Function

• If there is a false alarm, you can temporarily silence it by pressing the Silence button on the app or by pressing the Test/Silence button on the device. The LED indicator will flash red once every 5 seconds and you will receive an instant notification from the app, telling you that the device has been temporarily silenced.
• The silence duration usually lasts for 9 minutes. After that, the device will return to standby mode, provided that the smoke concentration has dropped below the alarm level.
• Note that the silence function will only silence the alarm for a short period. It will NOT correct any problems.

LED Indicator and Audible Alarm

Technical Specifications

NOTES

1. Battery life Is calculated on the current ratings In the weekly test mode and standby mode. If Its operation mode changes to on alarming condition, the battery life will be decreased accordingly.
2. This smoke alarm functions between 40 and 100°F (4.4 and 37.B”C). Prolonged exposure to lower or higher temperatures con reduce battery life and affect device performance. We do not recommend operating the device beyond Its temperature range.

Maintenance

General Maintenance
Follow the steps listed below for optimum long-term performance:

1. Test the device once a week by pressing the Test/Silence button, ensuring the device functions properly. Note that this only tests the electronics in your alarm rather than smoke.
2. Clean the alarm every three months. Remove the device from the ceiling or wall and clean the cover and vents with a soft, damp cloth. Be sure to properly reinstall the device after cleaning.
3. Do not clean the device with detergents or solvents, or spray air fresheners or hair spray near the device, as these may lead to a malfunction.
4. Do not paint the device, as it will seal the vents and reduce the sensitivity of the smoke sensors.
5. Do not tamper with this device, as this may lead to electrical shock or malfunction.
6. Do not disassemble the device to clean the interior. Doing so will void your warranty.

Weekly Test

• Test the alarm once a week, when you turn on the device for the first time, and every time you replace the battery or reconfigure the device.
• To test the alarm, press the Test/Silence button – the device should beep 3 times. If you hold down the Test/Silence button for longer than 3 seconds, the smoke alarm will re-enter the pairing process, and all previous settings will be erased.
• Note that this will only test the electronics. If the device fails to deliver an audible test signal, please refer to the Troubleshooting section.

Battery Replacement

1. Remove the smoke alarm from the mounting bracket by twisting counterclockwise.
2. Take out the old battery and install a new one, making sure to match the battery’s polarities.
3. Test the alarm by pressing the Test/Silence button on the device.
4. Attach the alarm onto the mounting bracket by twisting clockwise until it is firmly secured.

NOTE : When you replace the battery, the LED Indicator on the alarm will flash red once and green for a few seconds, Indicating the alarm is back online. If the LED indicator flashes green for longer than 2 minutes, you will need to re-add the alarm to the system by repeating the steps above.

Troubleshooting

• Check the batt ery.
• Firmly press the Test/Silence button.

False alarms are triggered when cooking or taking a shower.| Improper installation lo cation or maintenance.|

• Avoid placing alarms near cook ng app lances, dusty areas, showers, or any areas where the temperature drops below 40’F (4.4′ C) or rises above 1OO’ F (37.S’C). See the “Installation Positioning” section.
• Clean the alarm every three months to avoid unwanted alarms caused by dust and dirt. See the “Maintenance e’ section.

The LED indicator tlashes red once every 60 seconds with one beep.| Low battery warning.| Replace the battery immediately.
The LED indicator tlashes red every 60 seconds with two beeps.| Malfunction.| Clean your alarm to see if it is functioning properly. If not, replace the device immediately.
---|---|---
The LED| Wi-Fi Disconn ection.| Make sure the smoke alarm is
indicato r flashes| | installed within the rou ter
green during a| | range and that there are no
test, or the app| | obstructions between the
shows the| | device and the router.
smoke alarm as| |
being “Offline”| |

Environmental Protection
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with Local Authority or retailer for recycling advice.

Manufacturer and Service Information

• Smartie International LLC
• Address : 160 Greentree Dr, Dover, DE 19904, USA
• Email : support@aegislink.co.uk

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>