USARemote JX35 Nissan Altima Key User Guide

: June 13, 2024
: USARemote

Table of Contents

JX35 Nissan Altima Key
COMPATIBILITY LOOKUP
FREQUENTLY ASKED QUESTIONS
Documents / Resources

Replacing car keys is simple and affordable again.™
USER GUIDE
Pairing Instructions for Nissan and Infiniti
Series II Replacement Smart Keys
www.CKESimpleKey.com
Instruction Manual Part Number: NSPSA-7050

JX35 Nissan Altima Key

IMPORTANT NOTES

You MUST have at least one smart key that already works with your vehicle in order to use the EZ Installer™. If you have no working keys, return the Simple Key to the retailer where it was purchased.
All existing, working smart keys must be present during the pairing process. Once you pair a new key, all previous keys will be erased from the memory. The others will not be functional until you pair them again.
The emergency key blade should be cut at your convenience. This key blade is inside your new Simple Key and can be used to unlock the doors should the battery in your smart key fail. It can be cut at any local hardware store.
Vehicle battery should be in good condition and fully charged prior to pairing the new key. Turn off headlights, radio, A/C fan, etc. to minimize battery draw during the process.
Do not use the EZ Installer while the vehicle is in motion. Unplug it from the OBD port before driving the vehicle.
Only original remote features will work, regardless of buttons included on the Simple Key. This key does not add remote features that your vehicle did not have before.
For your security, a tamper-evident security label is installed over the EZ Installer connector. If this label is missing, damaged, or the word “VOID” appears on the EZ Installer when you receive the product, please contact Car Keys Express for a new one.
Before pairing, familiarize yourself with the Simple Key’s compatibility with the make, model, and year of your vehicle below.

LET’S GET STARTED
Simple Key requires two steps: “ACTIVATION” and “PAIRING.” It is important to follow these steps in order to successfully complete setup.
If you skip a step, the key WILL NOT work properly, and you’ll have to repeat the setup process.
Find your ACTIVATION CODE in the following chart by referencing your vehicle’s make, model, year and the button configuration of your key’s remote.

COMPATIBILITY LOOKUP

MAKE/MODEL| YEAR| 3 BUTTON REMOTE| 4 BUTTON REMOTE W/ TRUNK| 4 BUTTON REMOTE W/ REMOTE START| 5 BUTTON REMOTE
---|---|---|---|---|---
NISSAN| | ACTIVATION CODES
Altima 4-Door| 2013-2015| | 42| | 51
Altima 4-Door| 2016-2018| | 24| | 15
Maxima| 2016-2019| | | | 15
Murano| 2015-2018| 13| | 14| 25
Pathfinder| 2013-2015| 31| 43| 41| 52
Pathfinder| 2016-2019| 13| | 14| 25
Titan| 2016-2018| 13| | 14|
INFINITI| ACTIVATION CODES
JX35| 2013| 43| 52
Q50| 2016-2018| 24| 15
Q60| 2017-2018| | 15
QX60| 2014-2015| 43| 52
QX60| 2016-2018| 34| 25

USARemote JX35 Nissan Altima Key - Remote Back Remote Back with Key Removed.

Visit CKESimpleKey.com for the most up-to-date vehicle compatibility lookup.

STEP 1 (OF 2) KEY ACTIVATION

Follow the steps below to ACTIVATE your new key. Once you have activated your key, follow STEP 2 (of 2) KEY PAIRING to pair the key to your vehicle.

First, simultaneously press the top and bottom buttons on the remote. The key’s light will light and stay on.
Using your ACTIVATION CODE found in the chart above, enter the first digit using the top button and the second digit using the second button down from the top.
For example, KEY CODE 14 is entered by pressing the top button one (1) time, then the second from the top button four (4) times.
Now, press and hold the bottom button for approximately 2 seconds.
a. The light will now blink back the ACTIVATION CODE you originally entered. If this does not match, go back to Step 1 to start over.
b. If the light blinks rapidly, go back to step 2 and retry the steps using your ACTIVATION CODE.
c. You may re-enter button codes anytime before the key is paired to your vehicle. After the key is paired to your vehicle, do not attempt to re-enter or change the button code. This will cause the key to not work.
Move on to STEP 2 (of 2) below to PAIR the remote to your vehicle.

STEP 2 (OF 2) KEY PAIRING
NOTE: The EZ Installer has on-screen instructions to guide you through pairing steps. The numbered steps below provide more detail. Read all instructions prior to starting.
Follow the instructions in the blue portion of the EZ Installer screen first.
After you have completed the step, follow the instructions in yellow to move to the next step. For example:

Press to continue…
⇒ Press Start button once.
◄ Yellow Instruction
◄ Blue Instruction

When you see the message “Press to continue,” press and release the button on the end of the EZ Installer after completing the step written in blue.
When you see the message “Hold to confirm,” press the button on the end of the EZ Installer for 2 seconds and release after completing the step written in blue.

Instructions have timing requirements. If you wait too long between steps, your vehicle’s computer may time out, requiring you to start over. Once you begin the pairing procedure, move at a quick and even pace.

Turn the dial on the EZ Installer to position 7.
Begin with the vehicle in PARK and the engine OFF.
Enter the vehicle and close all doors.
Remove the security label from the EZ Installer and insert it firmly into the on-board diagnostic (OBD) port located under the dash.
a. The location of your vehicle’s OBD port can be found in the owner’s manual.
To continue, press and hold the EZ Installer button for 2 seconds, then release.
All of your keys will be erased once the procedure starts. If you do not have all keys available (new and existing), unplug the EZ Installer now. Otherwise, press and hold the EZ Installer button for 2 seconds, then release, to continue.
Turn the hazard lights on. Press the EZ Installer button to continue.
Press the brake and vehicle’s Start button to start the vehicle. Wait for the next screen.
a. NOTE: If the vehicle does not start, press the EZ Installer button as instructed and wait approximately 20 seconds.
Press vehicle’s Start button once to turn engine off. Press EZ Installer button to continue.
Do not press the brake pedal through the rest of the process. Press the EZ Installer button to continue.
Press and hold the vehicle Start button for a few seconds until dash lights turn on. Press the EZ Installer button to continue.
Press the vehicle’s Start button once. Dash lights will turn off. Press the EZ Installer button to continue.
The vehicle is now in pairing mode. Press the EZ Installer button to continue.
Hold the key you want to pair with the buttons facing you. (Review Fig. 1) Press the vehicle’s Start button with the top of the key and release as seen below. Do not hold the Start button down. a. After pressing the start button, hold the key near the Start button until the security light on your dashboard flashes 5 times. (Review Fig. 2) b. Press the EZ Installer button to continue.
Press the vehicle’s Start button once. Dash lights will turn off. Press the EZ Installer button to continue.
To pair additional keys, press and hold the EZ Installer button for 2 seconds and release.
a. Pick up unpaired key and press the EZ Installer button to continue.
Repeat steps 14-15 with the next remote.
Once you have paired all available keys, press the EZ Installer button once to continue.
To exit key pairing mode, using one of the keys you have already paired, press the vehicle’s Start button with the top of the key to turn the dash lights on. Press it again to turn the dash lights off. Press the EZ Installer button to continue.
When pairing is complete, the EZ Installer will sound a short tone.
Unplug the EZ Installer. If the EZ Installer is left in the OBD port for more than 5 minutes, an alarm will sound, reminding you to remove it.
Turn off hazard lights.
Press the brake and start the vehicle.
Test all keys.

FREQUENTLY ASKED QUESTIONS

Can I use the same EZ Installer on other vehicles?

No, the EZ Installer will be locked to the first vehicle it is used on. You may add more keys to the same vehicle again as needed, but it will not work on different vehicles.

The original key works, but the new key won’t pair to my car, or some of the remote buttons do not work correctly.

The EZ Installer was unplugged BEFORE step 13 of Step 2 KEY PAIRING.

Insert the EZ Installer back into the OBD port and begin back at Step 1. Keep the EZ Installer inserted into the OBD port until you have completed the Step 2 KEY PAIRING.

The EZ Installer was unplugged AFTER step 13 of the KEY PAIRING. - OR - The vehicle won’t start and the light above the Start Button flashes when pressed.

The vehicle is still in pairing mode. See the image in step 14. Press and release the Start button with your original key. (Do not hold the Start button down.) Keep the key near the Start Button for fifteen seconds. Repeat this 3 more times. At the end of this you will have only one original key paired with the vehicle, and it will Start the vehicle normally. Start the pairing process again at the beginning of Step 2 KEY PAIRING to try to pair all original and new keys again.

The vehicle won’t start with the new key or old keys after attempting to pair.

FCC AND ISED REGULATORY STATEMENT
MODEL: NSSSL-G010
FCC ID: X32-NSSSG010
IC: 8797A-NSSSG010
This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this device not expressly approved by iKeyless LLC could void the user’s authority to operate the equipment.
HELP
For help or assistance, please contact technical support at: 888-598-8910.
OTHER KEYS
Visit CarKeysExpress.com to find a variety of award-winning products, like Universal Car Keys, Universal Car Remotes, and OEM keys and remotes. New Chrysler, Dodge, Jeep, Ram, Ford, Honda, and Toyota Simple Keys are coming soon.

Replacing car keys is simple and affordable again.™
Patent US10755506B2
Designed and assembled in the USA
12101 Sycamore Station Place Ste. 140
Louisville, KY 40299
© 2023 Car Keys Express
www.CKESimpleKey.com