AUDIO EAHANCEMENT XD SOLO Wireless Sound Speaker System User Guide

AUDIO ENHANCEMENT XD SOLO Wireless Sound Speaker System

Product Information

• Tweeter: One tweeter is included in the product.
• Woofer: Eight woofers are included in the product.
• MP3 Player and Bluetooth Indicator: Indicates the status of the MP3 player and Bluetooth function.
• ALD Line Output Master Volume: Controls the master volume of the ALD line output.
• Voice Override Button: Activates voice override feature.
• Charging Power Connector: Connects the power source for charging.
• Microphone Linking Button: Used for linking the microphone to the system.
• Tone Controls Line Audio In : Adjusts the tone of the audio input from external sources.
• Battery Level Monitor : Monitors the battery level of the microphone.
• Power Switch: Turns the power on/off.

Product Usage Instructions

Microphone Linking

1. Ensure the microphone is turned off.
2. Press and hold the Link buttons on the Teacher Microphone until it links (large red button).
3. Successful linking will produce a beep and the BATT LED on the microphone will glow green.

OVERVIEW

LINKING XD TEACHER MICROPHONE TO THE XD SOLO®

1. With the microphone off, press the Link button on the back of the XD Solo® (Large red button).
2. Press and hold the PWR/MUTE and REC buttons on the Teacher Microphone until the microphone links.
3. Successful microphone linking will produce a beep through the system, and the BATT LED on the microphone will glow green.

LINKING XD STUDENT MICROPHONE TO THE XD SOLO®

1. With the microphone off, press the Link button on the back of the XD Solo® (Large red button).
2. While holding, use your thumb to slide the TALK button up into to the on position.
3. Successful microphone linking will produce a beep through the system, and the BATT LED on the microphone will glow green.

REMOTE VOLUME CONTROL OF MICROPHONES

XD TEACHER MICROPHONE (OWN) LEVEL ADJUSTMENT
Press either the UP or DOWN arrow button to increase or decrease the volume level of the Teacher Microphone. A blue LED over the OWN (for own microphone) will flash with each press.

The SELECT button determines which level will be controlled by the UP/DOWN buttons.

XD STUDENT MICROPHONE (OTHER) LEVEL ADJUSTMENT
To adjust the XD Student Microphone (OTHER) volume, first press the SELECT button so that the LED over the OTHER label comes on. Now press the UP/DOWN buttons to control the level of the OTHER microphone.

BATTERY REPLACEMENT

Make sure the power cable is unplugged and the power switch is in the OFF position before changing the batteries. Only replace with batteries that are the same size and rating as the original (12V – 2.8 AH Sealed Lead Acid).

1. On the back of the XD Solo®, you will see a large black plate. Remove the 4 screws around the edge of the plate.
2. Once you remove the plate, carefully pull the batteries out far enough to reach the wires. Notice that wires are color coded red for the Positive(+) terminal and black for the Negative(-). Carefully pulling on the wire clip, detach the wires from one battery and reattach to the same terminals on the replacement battery. Repeat this step for the next battery. This is easiest with needle nose pliers.
3. When sliding the batteries back into the compartment, watch to make sure the wires do not pull away from the battery’s terminals. If this occurs, gently push the connector with a link pair of pliers to get a tighter fit.
4. Although the replacement batteries are charged, it’s still suggested to charge the XD Solo for at least 12 hours before use.

REMINDER
A good tip to prolong the life of your batteries is to leave the XD Solo plugged into AC power when not in use. This will ensure you always have a fully charged unit and will prevent the batteries from self-discharging. The XD Solo has an overcharge circuit so leaving the unit plugged in will not hurt the batteries or the unit.

BLUETOOTH PAIRING

1. Press the power/MODE button to activate the Bluetooth function. Press the power/MODE button again to turn the Bluetooth function off.

2. When the Bluetooth function is activated successfully, the screen will show
   “Bluetooth Disconnected”, then it is ready to pair.

3. Activate the Bluetooth connection on any Bluetooth capable device.

4. Find the device name “TQ8” on the pairing list to connect the device.

5. When the paring is successful, the speaker will emit a tone and the screen will show “Connected.”

6. The speaker is ready to stream audio from the device.

AudioEnhancement.com ·
800.383.9362

References

• Home - Audio Enhancement

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>