hesotec electrify eLight Outdoor Light Instruction Manual

Installation and operating instruction
eLight – Outdoor light / socket
Models: White/Color – S/L – Single/Double/Triple
Version: 08.2023hesotec electrify gmbh
Rubbertskath 34
46539 Dinslaken / GER
HR – Nr. HRB 31112 AG Duisburg
St. – Nr. 101 / 5707 / 2333
UID – Nr. DE320783037
Phone +49(0) 2064 / 60 105 – 60
Fax + 49(0) 2064 / 60 105 – 50
Web: electrify.hesotec.de
E-Mail: electrify@hesotec.de

Important Information and safety instructions

1.1 Foreword
We are pleased that you have chosen the eLight outdoor light / socket from hesotec electrify. With the electrify eLight you invest in an innovative technology, combined with a sophisticated design and robust compactness.
The eLight complies with all existing safety guidelines and standards.
Read these installation and operating instructions completely before you start with the installation and commissioning. Keep this manual for future reference.
1.2 General safety instructions
To ensure proper installation and safe operation, follow the safety instructions given in this manual. Improper handling or non-compliance with the safety instructions may result in damage to the device itself, serious injury, fire or death. It is also advisable that every user of the eLight has access to content-related aspects about operation and in particular to safety instructions.
The installation, commissioning and maintenance of the electrify eLight may only be carried out by a qualified electrician. The operation of the eLight may only be carried out after a technically perfect installation with subsequent acceptance. Fauls and repairs that lead to damage to persons, to the device itself or other consumers may only be carried out by qualified specialist personnel.
In case of malfunctions and malfunctions due to a faulty installation, first contact the company that carried out the installation. If the problem persists, contact the hesotec electrify hotline.
Telefon +49(0) 2064 / 60 105 – 60
Mail electrify@hesotec.de
hesotec electrify assumes no liability for the following cases in the event of personal injury or property damage:

• Disregard of the installation and operating instructions
• Installation of unqualified technical personnel
• Structural alterations to the outdoor light / socket
• Improper handling
• Use of unauthorized spare parts or accessories

1.3 Safety instructions in this manual
This manual contains essential information for the installation and commissioning of the eLight of hesotec electrify. The following safety instructions are essential to be read and followed
The warnings contained in this installation and operating manual must be observed with great care. The meaning of the individual markings is described below:

Safety note on a hazard with electrical voltage
Non-observance of the instructions may result in electrical damage to the device itself, serious injury, and death.
**| ATTENTION !
Safety information on a hazard
Non-observance of the instructions may result in damage to the device itself or other consumers. Execution with special care!
**| NOTE !
Important information and special features
For a successful operation, the instructions should be carried out as needed.

Product overview and dimensions

In this chapter you will get an overview of product information with the necessary dimensions for the optimal planning and preparation.
2.1 Type plate

Information on the type plate:

• Manufacturer
• Series
• Model
• Power
• Serial number
• Manufacturing
• Rated cuerrent
• Nominal voltage
• Nominal frequency
• Power supply
• Protection class

2.2 eLight Models
The purchased electrify eLight is already fully assembled and delivered after successful quality control. It is only a secured supply line between the house sub-distribution and the outdoor light / socket needed. The respective requirements for the power connection can be found in the technical data.

Dimensions on the example, left: eLight S Double Model; right: eLight L Triple Model (measurement unit mm)
2.3 Ground anchor (Art.-No.00010276)
For mounting the eLight, hesotec electrify recommends the ground anchor included in the scope of delivery, which is inserted into the ground or alternatively poured into concrete. The prefabricated screw connection points make it easier to install the eLight.

Top and side view of ground anchor (measuring unit mm)Three-dimensional view of ground anchor

2.4 Technical Data
General technical details eLight series

removing the jumpers
Protective class| 1
Socket| E27 max. 4/250
Illuminant| depending on version (60×110 mm)
Energy efficiency class| F
Number of sockets| depending on version (0 to 3 pcs.)
Theft protection| Safety screws
Operating temperature| -20 °C to +45 °C
Protection class| IP44
Material| VA 1.4301
Material thickness| 2 mm

Installation

3.1 Demands on Location of eLight
DANGER !
Safety note on a hazard with electrical voltage
Pay attention to a proper installation. Non-observance of the requirements leads to a danger with electric voltage.
The electrify eLight is for outdoor and indoor use designed. For the installation of the outdoor light / socket, regulations regarding the location of installation must be ensured. Only in this way safe operation can be guaranteed.
Im Folgenden werden zu erfüllenden Anforderungen dargestellt:

• No instillation in vulnerable areas with a high risk of flooding.

• No instillation in vulnerable areas with a risk of explosion.

• Enough distance to other technical equipment.

• No direct spray water.

• Ambient temperature between -25 °C and 45 °C (-13°F and 113°F).
  For installation of low-voltage systems, the specifications IEC 60364-1 and IEC 60364-5-52 must complied.

• In order to withstand mechanical stresses, the mounting surface must be designed

• with sufficient strength.

• Make sure that the power supply is sufficiently dimensioned. Note that the sizing does not exceed the slot of the cable routing of the socket. (Information on power connection: see technical data)

NOTE !
Important information and special features
Avoid a confusing installation site to prevent unnecessary damage to the charging station.

3.2 Assembly of eLight
DANGER !
Safety note on a hazard with electrical voltage
Make sure that the supply line is de-energized at the time of installation.
Failure to observe the safety instructions can lead to a risk of death due to electrical voltage.
The electrify eLight should only be installed by qualified personnel. Please refer to the respective subchapters for the respective assembly steps. Make sure that the supply line is de-energized at the time of the assembly!!
3.2.1 Assembly with ground anchor
The eLight is already preassembled in the factory. To assemble the outdoor light / socket in combination with the ground anchor, proceed as follows:

1. DIN 7991 M5x12 A2
2. Terminal strip
3. Cable bushing
4. Plug
5. DIN 912 M8x30 A2
6. Socket
7. Ground anchor

Montage in Kombination mit Bodenanker

1. First loosen the 3 side screws at the lower end of the eLight. (similar to DIN 7991 M5x12 A2)
2. Then carefully pull the black base out of the housing.
3. Guide the supply line through the cable gland of the base and screw it to the ground anchor with the screws included in the scope of delivery. (DIN 912 M8x30 A2)
4. Before screwing the charging station to the base, read the chapter „3.3 Electric installation of the eLight“.
5. After the successful electrical installation, place the charging post on the base and screw it with the 3 lateral screws. (similar to DIN 7991 M5x12 A2)

3.2.2 Assembly on an alternative Ground
The electrify eLight is already preassembled in the factory. To install the outdoor light / socket on an alternative ground, proceed as follows

Installation on alternative ground

1. DIN 7991 M5x12 A2

2. Terminal strip

3. Cable bushing

4. Plug

5. DIN 912 M8x30 A2

6. Socket

7. Ground foundation

8.  First loosen the 3 side screws at the lower end of the eLight. (similar to DIN 7991 M5x12 A2)

9. Then carefully pull the black base out of the housing.

10. Place the base on the existing floor foundation and level it.

11. Mark the attachment points of the base to the foundation.

12. Drill the previously marked holes (ø 10 mm). Use the supplied assembly set for fastening. Make sure that the fastening dowels are sunk into the foundation and do not protrude above it.

13. Guide the supply line through the cable bushing of the base and screw it down with the screws included in the scope of delivery. (DIN 912 M8x70 A2)

14. Before screwing the charging station to the base, read the chapter „3.3 Electric installation of the eLight“.

15. After the successful electrical installation, place the charging post on the base and screw it with the 3 lateral screws. (similar to DIN 7991 M5x12 A2)

ATTENTION !
Safety information on a hazard
Make sure that the ground foundation has sufficient strength. Failure to follow the instructions may result in damage to the device itself or to other consumers.
3.3 Electrical Installation of the eLight
DANGER !
Safety note on a hazard with electrical voltage
Make sure that the cables are de-energized at the time of installation.
Failure to follow the instructions may result in a risk of death due to electrical voltage.
ATTENTION!
Safety information on a hazard
Failure to follow the instructions may result in damage to the device itself or other consumers. Execution with special care!
The electrical installation of the charging station may only be carried out by qualified personnel. When installing the electrical system, make sure that the cables are not damaged or crushed. These could interfere with the functions in later use, cause defects or even cause a fire.
The following table shows the connection diagram of the connection point between the ground side supply line and the eLight cables including the functional description

Connection diagram terminal strip eLight
NOTE !
Important information and special features
Slots 1-4 & 5-6 bridged together. If required, the jumpers can be removed for separate control.
3.3.1 Connection description eLight variants

3.3.2 Electrical Installation of the Outdoor light / socket
The electrify outdoor light / socket is already preassembled in the factory and wired electronically. All you have to do is connect the supply line to the connection socket.
For the electrical installation of the charging station, proceed as follows:

1. Connect the cable coming from the ground to the terminal strip according to the terminal label. (1,2,3,4,5,6,7)
2. Insert the plug coming in from the charging station into the terminal strip.

Wiring the eLight

Operation

The following graphic shows the main operating elements of the eLight:

Operating elements of the eLight

Change illuminant

The outdoor light / socket eLight is already delivered with an integrated E27 illuminant. This can be replaced if necessary.
DANGER !
Safety note on a hazard with electrical voltage
Make sure that the cables are de-energised at the time of replacement.
To replace the illuminant in the eLight, proceed as follows:

1. Loosen the grub screw at the top of the eLight.
2. Then carefully remove the light unit.
3. Now replace the illuminant and reassemble everything in reverse order.

NOTE !
Important information and special features
To ensure a tight seal, a high compressive force is required for assembly. We recommend a firm base.

Repair work

DANGER !
Safety note on a hazard with electrical voltage
Make sure that the cables are de-energized at the time of repair. Nonobservance of the safety instructions can lead to a risk of mortal dangerdue to electrical voltage.
Repairs to the charging station may only be carried out by a qualified specialist. It should be noted that only spare parts released by hesotec electrify are permissible. If necessary, contact the manufacturer.

Maintenance / Disposal

DANGER !
Safety note on a hazard with electrical voltage
Make sure that the cables are de-energized at the time of maintenance.
Non-observance of the safety instructions can lead to a risk of mortal danger due to electrical voltage.
The eLight outdoor light / socket from hesotec electrify are designed so that they are generally maintenance-free. Nevertheless, visual inspections should be carried out at regular intervals.
7.1 Maintenance
hesotec electrify recommends carrying out a test at intervals of 6 months.
• Outdoor light / socket

• Check the eLight for visual damage and defects.
• Check the functionality of the socket.
• Check whether there is any damage to the hinged cover.
• Check the stability of the eLight on the ground anchor/foundation.

7.2 Disposal
Old electronic devices must be disposed according to the current guidelines and disposal regulations of the respective location. Disposal with household waste is strictly prohibited! Only uses a collection point intended for electronic waste or dispose it through a specialist retailer.
The disposal of the packaging material can take place via collection points for paper and plastics.

Appendix

8.1 CE-Label and Declaration of Conformity
The eLight outdoor light / socket of hesotec electrify is marked with a CE label. A copy of the Declaration of Conformity will be presented later. On request, this is available from hesotec electrify gmbh.
CERTIFICATE
CE – DECLARATION OF CONFORMITY

This declaration certifies the conformity to the specified directives but contains no assurance of properties.

hesotec electrify gmbh
Rubbertskath 34
46539 Dinslaken / GER
Telefon +49(0) 2064 / 60 105 – 60
Fax +49(0) 2064 / 60 105 – 50
E-Mailelectrify@hesotec.de
Webelectrify.hesotec.de

References

• hesotec electrify – Ladelösungen der Zukunft
• hesotec electrify – Ladelösungen der Zukunft

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>