mitoredlight BADW9BFEUYY Universal Stand User Manual
- June 13, 2024
- mitoredlight
Table of Contents
mitoredlight BADW9BFEUYY Universal Stand
PRECAUTIONS
We reserve the right to modify or alter instructions. Nomodification or alteration without formal notice.
- The universal stand is used for Mito Red Light Therapypanels only.
- Please ensure the stand is placed on level floor.
- Please ensure the wheels are locked after installation.
- Children should not use unless approved by a physician.
WARNING
Severe personal injury and property damage can result fromimproper installation or assembly. Read this user manual carefullybefore beginning.
- If you do not understand the instructions or have any concernsor questions, please contact Mito Red Light (contact details canbe found on page 16).
- Do not install or assemble if the product of hardware isdamaged or missing, if you require replacement parts, pleasecontact Mito Red Light for assistance.
- This product fits most 21” x 71” maximum weight of red lighttherapy panel is 46 KG or 100 lbs.
- Do not use this product for anything other than the originaldesign.
- This product contains moving parts, please use with caution.
- The manufacturer disclaims any liability that the modifications,improper installation, or installation over the specified weightrange. The manufacturer will not be liable for any damagesarising out of the use of or inability to use, the product.
- All images are a reference only.
PARTS LIST
STEP 1: ADD CASTOR WHEELS TO BASE INSTALLATION
STEP 2: POST ASSEMBLY TO BASE INSTALLATION
Note : Make sure cable management holes are facing therear of the house.
STEP 3: INSTALL TELESCOPIC MOUNTING POLES
Step 1 : Use thumb or finger to depress the right upper pole
springplunger ball located at the cable window, pull upper pole upwarduntil
your desired height. Twist upper pole towards the plungerholes direction and
engage the spring ball into the plunger holeand set as shown in figure 1.
Step 2: repeat with the left pole.
VERTICAL STAND ASSEMBLY INSTRUCTIONS
SELECTION OF MOUNTING PATTERNS
Step 1: Screw the vertical stand mounting brackets to panel as shown(single panel example)
See product specific user manuals / video tutorials for bracket
installinstructions as the brackets vary by Series.
https://mitoredlight.com/pages/user-manual
Step 2:
Hang the panel (with verticalmounting brackets) on thecross bracket. Then to
securethe panels to the stand, installparts C and D on each side ofthe
vertical brackets as shown(fig-4).
INSTRUCTIONS: VERTICAL STAND KEY FINAL ASSEMBLY TIP
Step 1:
Align attachment D as shown inthe image to the below.
Some helpful assembly videos are available here: https://mitoredlight.com/pages/user-manual
Step 2:
Screw in the attachment. Locationof the attachment on the stand is shownin the
image below. The holes for the screws and attachmentsare located on the
outside of the outerbrackets.
PRODUCT SPECIFICATIONS
HORIZONTAL STAND ASSEMBLY INSTRUCTIONS
The base and telescopic mounting installation is the same as the previous
example. Then connect and fix Horizontal L-form mounting kit ‘A’ with the
telescopic mounting, as shown below 
Attach poles with 60mm screws to steel L-form plates as shown below.
SCREW HORIZONTAL METAL BRACKETS TO PANEL
-
Screw horizontal metal brackets to panel. *note – see productspecific user manuals / video tutorials for bracket install instructionsas the brackets vary by Series
https://mitoredlight.com/pages/user-manual
-
Fix panel (with horizontal metal bracket attached) with boltsas shown below:
MITOADAPT BRACKET INSTALLATION
MITOADAPT BRACKET INSTALLATION
If you have any further questions, please feel free to contact us at: [email protected]
You can also call our phone number
Monday – Friday 9am – 5pm MST
+1 866-861-6486
Mail correspondence can be sent to:
Mito Red Light, Inc
9319 N 94th Way, Suite 400 Scottsdale, AZ 85258
References
- Mito Red Light | Red Light Therapy Devices for your Home
- User Manuals and Video Tutorials | Mito Red Light