mitoredlight MitoADAPT Panel User Guide
- June 11, 2024
- mitoredlight
Table of Contents
MitoADAPT
QUICK USER GUIDE
MitoADAPT Panel
Usage Guidelines For first time users, we recommend starting out with 2-3
minute treatments per area, and slowly working up to a 10-minute session over
the course of 2-3 weeks as your body acclimates to the therapy.
Modes
We recommend starting with Mode 1 as you get acclimated to the light. Then we
recommend rotating your sessions through Modes 1-6 (i.e. one day do a session
with Mode 1, the next session use Mode 2, etc).
Modes 1 though Mode 6 are various combinations of Red (peak 630nm & 660nm) and
NIR (peak 810nm & 850nm) light. See the user manual for a summary of the
modes.
Modes 7-10 have only 50% of the LEDs lit and can be used for gentler sessions.
Mode 11 is 100% NIR and is available only through the app.
Troubleshooting
If the control panel is not working, make sure you arc connected to power and
that the power switch on the back of the device is turned on.
When resetting the Default Time on the Settings Screen, after the time is
selected hit the ‘GO- button then turn the power switch off then back on.
If there is no light coming from the ponel when the session is started,
confirm that the brightness is not set to 0% (also note that NIR light
830nm/850nm is invisible to the naked eye).
If app will not connect, make sure you are within 5 feet of the panel, close
the app on your device and restart. Turn the panel off and on. Make sure your
Bluetooth is enabled on your mobile device and your panel.
Congratulations on your new MitoADAPT panel! Below is a quick start-up guide
to get you on your way to your red light therapy pronto! If you need more
detailed instructions or need more information, check out our main user manual
of www.mitoredlight.com/pages/user-
manual
Quick set-up without using the Mito Red Light app
Unbox your panel, plug in the power cord, and turn on the power switch.
This is the Home Screen. Using the ‘+’ and ‘-‘ buttons you can adjust the time for the current session. If all the other settings look good, press ‘GO’ to start and stop your session.
From the Home
Screen press ‘SET’ to navigate to the Settings Screen. To adjust the Default
Time, Mode, Bluetooth connectivity, and Brightness settings press ‘SET’.
Press +/- to change any specific setting. Press ‘SET’ to toggle between each
setting. Once you have
adjusted these settings, press ‘GO’ to go back to the Home Screen, and then
press ‘GO’ again to start/stop your session. Please note, changing the Default Time on the Settings Screen
will not affect the current session. The panel must be turned off and back on
to display the new Default Time.
Connecting panels
We know you will want to add more MitoADAPT panels to your set-up, so we have
you covered.
Important: Prior to starting your session, please connect the panels as
explained below.
Use the signal cable to connect each panel. Select which of your panels will
be the main panel that controls the others.
Place one end of the cable in the port marked ‘OUT’ on the main panel and put
the other end in the ‘IN’ port. If you hove multiply panels continue this
process.
This may sound tricky, so check out the main user manual if you need more
guidance!’ Repeat this process with the jumper power cables going from the
main pane to the following panels.
Be sure to leave the IN port on the primary device unoccupied.
If the primary device screen reads “SS:SS” double check to make sure there is
not a cord plugged into the IN port on that device.
Continue to the next steps to set up the app.
‘Check out the main user manual for more assistance at
www.mitoredlight.com/pages/user-manual
Quick set-up using the Mito Red Light app
Yes, we have an app so you can control your MitoADAPT from your mobile
device.
Unbox your panel, plug in the power cord, and turn on the power switch. If you
have multiple devices please make sure the panels are connected before
starting the session.
Make sure the Bluetooth function is enabled on your primary device.
Download the
Mito Red Light app using the QR codes below! Start the app and fill out the
brief onboarding questions.
Accept permissions and make sure the Bluetooth on your mobile device is turned
on.
https://play.google.com/store/apps/details?id=com.mitoredlight&pli=1| https://play.google.com/store/apps/details?id=com.mitoredlight&pli=1
Select one of the 11 modes, and follow the prompts. If you need to stop your session, press ‘Stop’ on your app or press ‘Co’ on the main panel. Note: Modes 9, 10, and 11 are near infrared light only. NIR light is invisible to the naked eye so it may appear that the session is not running. Please rest assured that significant light energy is being emitted from the panel.
www.mitoredlight.com User Manual and
Instructional Videos
This user manual and instructional videos can be found here:
https://mitoredlight.com/pages/user-manual
FOLLOW US!
mitoredlight
mitoredlightofficial
@MitoRedLight
@mitoredlightofficial
References
- Mito Red Light | Red Light Therapy Devices for your Home
- User Manuals and Video Tutorials | Mito Red Light
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>