WeTekom 81 48 65 Socket Polarity Tester Instruction Manual

: June 13, 2024
: WeTeKom

Table of Contents

WeTekom 81 48 65 Socket Polarity Tester
Introductions
Use
LED indicators
Cleaning and storage
Technical data
EC Declaration of Conformity
Disposal
Customer Services
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WeTekom 81 48 65 Socket Polarity Tester

WeTekom-81-48-65-Socket-Polarity-Tester-PRODUCT-IMG

Introductions

Please note to avoid Malfunctions, damage and health risks Impairments following information:

This operating manual belongs to this product. It contains important information on commissioning and handling. Please include the user manual with the product when you use it
Pass it on to third parties!
Do not leave packaging material lying around carelessly. Plastic bags etc. can become dangerous toys for children. Hold that
Keep the device away from children. It’s not a toy.
Do not expose the device to direct sunlight,
Moisture, dirt, strong heat, hot light sources or strong magnetic fields out of.
To avoid electric shock the regulatory measures must be observed when using Voltages greater than 33 V rms alternating voltage and 70 V DC voltage is used. Values above the information are considered dangerously active under normal conditions.
The device is designed for use up to 2000 m above sea level.
If to check a socket or a
Intermediate adapter connecting cable used it must be ensured that the adapter is in perfect condition and that the protective conductor connection of the adapter is connected throughout.
The use of intermediate adapters without a continuous protective conductor connection leads to incorrect test results.
The socket tester may only be used properly grounded networks can be used.
Before each measurement, make sure that the testing device is in perfect condition.
The device may only be used under the conditions and for be used for the purposes for which it was designed. The safety instructions are for this purpose.
Technical data with the environmental conditions and use in a dry environment to be noted.
If the device is damaged, the device must not be used continue to be used. Do not disassemble the device and do not attempt any repairs.
The device does not contain any that can be replaced by you or parts to be repaired. Contact
Questions and problems to our customer service.

Use

Plug the device into the socket to be tested.
Read the test result using the three LEDs on the front of the device (see table).
After measuring, pull the device out of the device Power outlet.

LED indicators

OK
PE (protective conductor) interrupted
L (phase) is missing
N (neutral conductor) interrupted
L + N (phase + neutral) swapped
L + PE (phase + protective conductor) swapped
L + PE (phase + protective conductor) swapped & PE (protective conductor) interrupted

Cleaning and storage

Always unplug the device before cleaning the socket.
Clean the device with a slightly damp cloth. Do not use harsh chemicals or abrasive cleaners for cleaning.
Do not immerse the device in liquids.
Store the device indoors dry place protected from dust, dirt and extreme temperatures.

Technical data

Rated voltage: 230V~ 50Hz
Surge protection: 300V
Operating temperature: 0 to +40 °C
Rel. humidity during operation: < 80%
Response threshold: < 50 V to earth
Dimensions: 60 x 60 x 65 mm
Weight: approx. 52g

Attention: Interchanging the neutral conductor and protective conductor (earth) will not be recognized by the device!

EC Declaration of Conformity

We, the Westfalia Werkzeugcompany, Werkzeugstraße 1, D-58093 Hagen,
We, the Westfalia Werkzeugcompany, Werkzeugstraße 1, D-58093 Hagen,
- declare under sole responsibility that the product.
- declare by our own responsibility that the product.
meets the essential protection requirements set out in the European directives and their changes are determined.
- is according to the basic requirements, which are defined in the European Directives and their amendments.
2011/65/EU Restriction on the use of certain dangerous substances Electrical and Electronic Equipment (RoHS)
2011/65/EU Restriction of the Use of certain hazardous substances in electrical and electronic equipment (RoHS)
2014/30/EU Electromagnetic compatibility (EMC) Electromagnetic Compatibility (EMC)
2014/30/EU EN 55011:2016+A1+A11, EN 61326-1:2013, EN 61000-3-2:2014, EN 61000-3-3:2013
2014/35/EU Low Voltage Directive (LVD) Low Voltage Directive (LVD)
2014/35/EU EN 61010-1:2010+AC+A1, EN 62311:2008
The technical documents are stored at QS at Westfalia Werkzeugcompany.
The technical documentation is on file at the QA department of the Westfalia Werkzeugcompany.

Hagen, on 8 August 2023 Hagen, 8 th of August, 2023

Disposal

Dear Customer,
Please help avoid waste materials. If you at some point intend to dispose of this article, then please keep in mind that many of its components consist of valuable materials, which can be recycled. Please do not discharge it in the rubbish bin, but check with your local council for recycling facilities in your area.