Brillian Network Automation Integrated System ERACK0001 Electronic Shelf User Manual
- June 4, 2024
- Brillian Network Automation Integrated System
Table of Contents
Brillian Network Automation Integrated System ERACK0001 Electronic Shelf
The reproduction of any part of this user manual, in any from (by photocopying, microfilming or any other process) or the processing and distribution of the contents by electronic means is prohibited without the expressed written consent of Brilliant. It is prohibited to copy the software or use it for other purposes. it is expressly prohibited to distribute copies of the software to third parties. Violators will be held liable for the damage.
Brief introduction of equipment
Brillian Material Handling Solution(BMHS)
We provide a FAB semi-automatic material handling solution. Through material
storage devices, integrating the BMHS system and database, product locations,
and determining the transmission route, optimal throughput and increase
productivity. Rack management collects all back status information, and
exchanges information on behalf of all eRacks and MES. Provides admin search
queries, work order inquiries, statistical analysis, etc. The lack shelf can
read the RFID tag on the foup by RFID antenna, transfer the carrier data to
the background for unified management, and then receive the foup information
from the background to the operator.
Feature of Product
- The BMHS system centrally monitors shelves of E-Rack.
- Integrate MES and BMHS real-time management systems to control all products in the factory.
- Significantly improve productivity.
- Flexible system configuration and higher utilization rate.
- Provide various statistical data to facilitate analysis and decision-making.
- RFID Reader helps to confirm whether the products and sites are correct before assisting production, which greatly reduces errors.
Description of a safety rule of MR E-Rack System
- This manual is only written for Purge System Module。
- Non-qualified or non-professional personnel are not allowed to operate or maintain the machine。
- “Operator” should read carefully the software operation in advance。
- “Maintainer”, in addition to getting familiar with software operation, should read carefully the maintenance manual and circuit diagram。
- Before the careful reading of the operation manual or before a thorough understanding of the machine function, it is not allowed to operate the machine singly, and it needs an experienced guy standing beside for instruction。
Instruction for transport
When transporting or moving a machine, it is suggested to use a cart for the
transport, please also wear steel shoes for personal safety. The cart should
be able to carry a load of more than 100Kg
- For scarping of equipment or disposal of waste, please follow the local regulations
- Instruction for illuminance in the work area: Please follow the lighting environment provided by the plant of the client send.
- The machine is not suitable to work in explosive circumstances
- Before ex-factory, the level of noise should be less than 80dB (A).
- About “Warnings and Cautions”
- When power is supplied, non-professional personnel should not operate it to avoid electric shock hazards.
- Before checking, maintenance and repairing, please turn off the power.
- Description of starting steps
- Turn on the breaker power.
- The facility department is suggested to be AC 100~230V
- Description of stopping steps
- Please use an externally connected screen or remote control program to confirm all the ports Purge program are all in idle states.
- After log in to the program, please select Quit to end the program.
- Turn off the breaker power.
- Install a lock for the breaker and lock it.
- Close the gas source switch at the facility end.
Facility Requirement&SPEC
FCC Rules
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
MR E-Rack 5X3
MR E-Rack 5X3 Module
Front Illustration
Electric control box
RFID PCB
MR E-Rack 5X3 Hardware
MR E-Rack 5X3 Operation Description Put a POD fixed on the goods which you need to get goods information. The Transponder has a data record for the good During the Host computer sent an order message to the CIDRW through RS232 or HSMS The CIDRW will sent back the goods information which is read from the Transponder by radio frequency.
Periodical Maintenance
Cleaning Plate
- Material： NA
- Manual tool： Cleanroom wiper、DI Water
- Notice： Before action, please confirm whether the machine is down
- PM Step： Cleanroom wiper cloth into the DI Water from inside to outside and from top to clean the Plate surface.
