JANAM XT40 Series Mobile Handheld Computer User Guide

June 13, 2024
JANAM

JANAM XT40 Series Mobile Handheld Computer

Product Information

The XT40 SeriesTM is a product manufactured by Janam Technologies LLC. It is a handheld device that comes with a rechargeable battery. The device is designed for various applications and is equipped with a range of features to enhance user experience.

Janam Technologies LLC is the trademark owner of the XT40 Series, Janam, and the Janam logo. The company assumes no  responsibility for any damage or loss resulting from the use of thedevice or this guide. It also disclaims any responsibility for loss or claims by third parties that may arise from the use of the product.

Battery Safety Guidelines:

  • Use only Janam XT40 Series batteries and recharge batteries using Janam approved charging accessories.
  • Avoid exposing the battery to excessive heat or cold. Do not short-circuit or incinerate the battery.
  • Prevent metal objects from touching battery contacts to avoid risk of burn or damage.
  • Do not disassemble the battery as there are no user serviceable parts inside.
  • If battery leakage is observed, avoid contact and properly dispose of the battery. In case of contact with battery leakage, rinse the exposed area with soap and water. If it contacts the eye, flush the eye with water for 15 minutes and seek medical attention.
  • Promptly dispose of used batteries, keeping them away from children. Do not disassemble or dispose of them in fire.
  • When discarding a battery, contact your local waste disposal provider to understand local restrictions for disposal or recycling of batteries.

Battery Charger Safety Guidelines:

  • Avoid using the equipment in areas where sparks are likely or possible.
  • Prevent contact between the equipment’s metal contacts and electrical sockets with metal objects.
  • The equipment is for indoor use only and should not be exposed to rain or any liquids.
  • Avoid using or storing the equipment in direct sunlight or hotareas such as parked vehicles, near heat ducts, or close to otherheat sources.
  • Keep the equipment’s metal contacts and electrical sockets free from debris that could obstruct charging or cause a shortcircuit.

Product Usage Instructions

To use the XT40 Series device:

  1. Ensure that you are using Janam XT40 Series batteries and recharge them using Janam approved charging accessories.
  2. Follow the battery safety guidelines mentioned above to ensure safe use and handling of the battery.
  3. Refer to the Product User Guide for detailed instructions on how to operate the device, including its features and functionalities.
  4. Make sure to read and accept the End User License Agreement before using the device or accompanying software program(s).
  5. For any questions or further assistance, contact Janam Technologies LLC. You can also visit their website at www.janam.com to access the Product User Guide.

Note: To protect against data loss, it is recommended to make backup copies of all important data on other media.

For additional content and resources, refer to page 1 of the user manual.

Battery Warning

CAUTION
IF MISUSED OR MISTREATED THE BATTERY MAY PRESENT A RISK OF FIRE OR CHEMICAL BURN. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
BATTERY SAFETY GUIDELINES.
Use only Janam XT40 Series batteries and recharge batteries using only Janam approved charging accessories. Observe the following guidelines for safe use of Li-Ion batteries:

  1. Do not expose the battery to excessive heat or cold. Do not short-circuit. Do not incinerate.
  2. To avoid risk of burn or damage to your battery, do not allow a metal object to touch battery contacts.
  3. Do not disassemble the battery. There are no user serviceable parts inside.
  4. If battery leakage is observed, avoid any contact with affected area and properly dispose of the battery.
  5. If you come in contact with battery leakage, rinse exposed area with soap and water. If it contacts the eye, the eye with water for 15 minutes and seek medical attention.
  6. Dispose of used battery promptly. Keep away from children. Do not disa ssemble or dispose of in
  7. When discarding a battery, contact your local waste disposal provider to understand local restrictions for disposal or recycling of batteries.

XT40 Series Quick Start Guide

Copyright 2019 Janam Technologies LLC. All rights reserved. XT40 Series, Janam and the Janam logo are trademarks of Janam Technologies LLC. Other product and brand names may be trademarks or registered trademarks of their respective owners. Janam Technologies LLC assumes no responsibility for any damage or loss resulting from the use of this guide. Janam Technologies LLC assumes no responsibility for any loss or claims by third parties which may arise through the use of this product. Janam Technologies LLC assumes no responsibility for any damage or loss caused by  deletion of data as a result of malfunction, dead battery or repairs. To protect against data loss, be sure to makebackup copies (on other media) of all important data. Follow all usage, charging and maintenance guidelines in the Product User Guide. If you have questions, contactJanam. For a copy of the Product User Guide, visit www.janam.com. Important: Please read the End User License Agreement for this product before using the device or the accompanying software program(s). Using the device or any part of the software indicates that you accept the terms of the End User License Agreement

Content and Additional Resources
To help you get started with your XT40 Series mobile computer, this guide features:

  • Hardware Overview
  • Getting Started
    • A. Install the Battery
    • B. Charge the Battery
    • C. Remove the Battery + Access MicroSD and SIM Card Slots
  • Battery warnings and safety guidelines. Contents of this guide are subject to change. For the most current version of this guide and additional product details, visit www.janam.com.
    For software updates and information, visit www.janam.com/product- zone.

BATTERY CHARGER SAFETY GUIDELINES.

  1. Do not use the equipment in or near areas in which sparks are likely or possible.
  2. Do not let equipment’s metal contacts and electrical sockets come in contact with metal objects.
  3. For indoor use only. Do not expose the equipment to rain or any liquids.
  4. Do not use or store the equipment in direct sunlight or in areas that are prone to get hot such as in a parked vehicle, near a heat duct or close to other heat sources.
  5. Keep equipment’s metal contacts and electrical sockets free from debris that could obstruct charging or could cause a short circuit.

Hardware Overview

  1. Camera
  2. Speaker
  3. SIM Card Slot
  4. MicroSD Card Slot

Getting Started

INSTALLING THE BATTERY

  1. To access the battery compartment, remove the handstrap by pulling down the plastic clip located on the bottom of the XT40. Move both tabs on the battery cover to the “unlock” position and pull the cover away fromthe device.
  2. Position the battery so that the text “Insert this direction.” is on the left side and snap into place.
  3. Replace the battery cover by positioning the bottom prongs first and snapping cover into place.
  4. Move both tabs on the battery cover to the “lock” position.

CHARGING THE BATTERY
Important Note: The main battery charges the backup battery in the XT40 Series device. When discharged, the backup battery requires approx. 1.5 hours to recharge.
To charge the battery using the included AC/DC Power Adapter Kit:

  1. Connect the AC/DC adapter to XT40 Series.
  2. Plug in the AC/DC adapter. Use only easily accessible wall sockets that are easily reached with the length of supplied power cable

To charge the battery using a Cradle Kit:

  1. Connect the power supply to the cradle.
  2. Plug in the power supply. Use only easily accessible wall sockets that are easily reached with the length of supplied power cable.
  3. Place the device in cradle. The LED on the device will illuminate to con irm connection.
  4. The battery is fully charged in approximately 2.5 hours.
  5. To charge a battery in the spare battery well, insert the battery into the well top down (connectors on the battery should face downward and to the back of the cradle) and gently press down. The LED light on the cradle will illuminate to con irm connection.

To charge the Backup Battery:

  1. Navigate to the Home Screen -> App drawer -> Settings -> Battery.
  2. Select “Backup Battery Charge” option.

ACCESSING SIM CARD SLOT and MICROSD CARD SLOT

  1. Remove the back cover.
  2. Remove battery from the XT40.
  3. MicroSD card slots and SIM slot are now accessible. Insert the MicroSD or SIM with gold-colored contacts facing downward.
  4. Replace the battery.
  5. Replace the battery cover.

FCC

FCC Caution

Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna

IC Caution
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
English:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause in terference, and (2) This device must accept any interference, including interference th at may cause undesired operation of the device.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals