Miele 11 660 200 Washing Machines Instruction Manual
- June 4, 2024
- Miele
Table of Contents
11 660 200 Washing Machines
Operating instructions for washing machines
To avoid the risk of accidents or damage to the machine, it is essential to read these instructions before it is installed and used for the first time.
en-GB
M.-Nr. 11 660 200
Contents
Warning and Safety instructions …………………………………………………………… 5 Operating the
washing machine ……………………………………………………………. 12 Control panel
…………………………………………………………………………………………. 12 How the control field
works……………………………………………………………………… 13 Caring for the environment
…………………………………………………………………… 14 Before using for the first time
……………………………………………………………….. 15 Washing environmentally and economically
………………………………………….. 17 1. Prepare the laundry…………………………………………………………………………… 18
2. Load the washing machine………………………………………………………………… 19 3. Select a
programme………………………………………………………………………….. 20 4. Add detergent
…………………………………………………………………………………… 22 Detergent dispenser drawer
…………………………………………………………………….. 22 CapDosing……………………………………………………………………………………………..
24 5. Start the programme…………………………………………………………………………. 26 Adding laundry
during a programme sequence (AddLoad) ………………………….. 26 6. End of programme
……………………………………………………………………………. 27
Spinning……………………………………………………………………………………………….. 28 Delay start
……………………………………………………………………………………………. 29 Programme chart
…………………………………………………………………………………. 30 Extra
options………………………………………………………………………………………… 34
Short…………………………………………………………………………………………………….. 34 Water +
…………………………………………………………………………………………………. 34 Pre-wash
………………………………………………………………………………………………. 34 Pre-ironing
…………………………………………………………………………………………….. 34 The following extras can be selected
in addition to the programmes…………….. 35 Programme
sequence…………………………………………………………………………… 36 Changing the programme sequence
…………………………………………………….. 39 Changing a programme (safety lock)
………………………………………………………… 39 Cancelling a programme ………………………………………………………………………….
39 Garment care label symbols………………………………………………………………….. 40
2
Contents
Detergent …………………………………………………………………………………………….. 41 The correct
detergent……………………………………………………………………………… 41 Water softeners
……………………………………………………………………………………… 41 Dispensing aids
……………………………………………………………………………………… 41 Fabric conditioner and liquid starch
………………………………………………………….. 41 Recommended Miele detergents
……………………………………………………………… 43 Recommended detergents in accordance with
Directive (EU) Nr. 1015/2010…. 44 Cleaning and care
………………………………………………………………………………… 45 Cleaning the external casing and the
control panel …………………………………….. 45 Cleaning the detergent dispenser drawer
………………………………………………….. 45 Hygiene info(Cleaning the drum)
………………………………………………………………. 47 Cleaning the water inlet filter
……………………………………………………………………. 47 Problem solving guide
………………………………………………………………………….. 48 The programme does not
start…………………………………………………………………. 48 The programme is cancelled and a fault
indicator light lights up in the control panel………………………………………………………………………………….
49 During the programme, a symbol appears in the time display ……………………… 50 At
the end of the programme, an indicator light lights up in the control panel …
50 General problems with the washing machine …………………………………………….. 51 An
unsatisfactory wash result ………………………………………………………………….. 53 The door will not
open…………………………………………………………………………….. 54 Opening the door in the event of a
blocked drain outlet and/or power cut …….. 55
Service…………………………………………………………………………………………………. 57 Contact in the event of a
fault ………………………………………………………………….. 57 Optional
accessories………………………………………………………………………………. 57 EPREL database
……………………………………………………………………………………. 57 Warranty
……………………………………………………………………………………………….. 57
Installation……………………………………………………………………………………………. 58 Front view
……………………………………………………………………………………………… 58 Rear
view………………………………………………………………………………………………. 59 Installation surface
…………………………………………………………………………………. 60 Transporting the washing machine to its
installation site……………………………… 60 Removing the transit bars
……………………………………………………………………….. 61 Fitting the transit bars
…………………………………………………………………………….. 63 Levelling the
machine……………………………………………………………………………… 64
Screwing out and adjusting the feet……………………………………………………… 64 Installing under a
continuous worktop ………………………………………………….. 65 Washer-dryer stack
……………………………………………………………………………. 65
3
Contents
The water protection system……………………………………………………………………. 66 Connection to the
water supply ……………………………………………………………….. 66 Water drainage
………………………………………………………………………………………. 68 Electrical connection
……………………………………………………………………………… 69 Consumption data
………………………………………………………………………………… 70 Technical
data………………………………………………………………………………………. 71 Programmable functions
………………………………………………………………………. 72 Choosing and selecting a programmable function
……………………………………… 72 Editing and saving a programmable
function……………………………………………… 73 Exit programming
level……………………………………………………………………………. 73 Sensor tone
……………………………………………………………………………………… 73 Lock
code………………………………………………………………………………………… 74 Control panel switch-off status
………………………………………………………….. 74 Memory ………………………………………………………………………………………….. 75
Longer pre-wash Cottons …………………………………………………………………. 75 Gentle action
…………………………………………………………………………………… 75 Reduce
temperature…………………………………………………………………………. 75 Water
plus……………………………………………………………………………………….. 76 Water plus level
………………………………………………………………………………… 76 Maximum rinse level
…………………………………………………………………………. 76 Suds cooling
……………………………………………………………………………………. 77 Anti-crease
……………………………………………………………………………………… 77 Low water
pressure………………………………………………………………………….. 77 Backlight brightness dimmed
……………………………………………………………. 77 Detergents and care products
………………………………………………………………. 78 Detergent………………………………………………………………………………………………. 78
Specialist detergents ………………………………………………………………………… 79 Fabric care
………………………………………………………………………………………. 80 Additives
…………………………………………………………………………………………. 80 Machine
care…………………………………………………………………………………………. 80
4
Warning and Safety instructions
This washing machine complies with all current local and national safety
requirements. However, inappropriate use can lead to personal injury and
damage to property. Read the operating instructions carefully before using the
washing machine. They contain important information on safety, installation,
use and maintenance. This prevents both personal injury and damage to the
washing machine. In accordance with standard IEC 60335-1, Miele expressly and
strongly advises that you read and follow the instructions in the chapter on
installing the washing machine as well as the safety instructions and
warnings. Miele cannot be held liable for damage caused by non-compliance with
these instructions. Keep these operating instructions in a safe place and pass
them on to any future owner. Correct application This washing machine is
intended for use in domestic households and similar working and residential
environments. The washing machine is not intended for outdoor use. It must be
used only as a domestic appliance to wash items which are specified by the
manufacturer as being washable on the wash care label. Miele cannot be held
liable for damage resulting from incorrect or improper use or operation. The
washing machine can only be used by people with reduced physical, sensory or
mental capabilities, or lack of experience or knowledge, if they are
supervised whilst using it or have been shown how to use it safely and
recognise and understand the consequences of incorrect operation.
5
Warning and Safety instructions Safety with children Children under 8 years of
age must be kept away from the wash-
ing machine unless they are constantly supervised. Children 8 years and older
may only use the washing machine unsupervised if they have been shown how to
use it safely and recognise and understand the consequences of incorrect
operation. Children must not be allowed to clean or maintain the washing
machine unsupervised. Please supervise children in the vicinity of the washing
machine and do not let them play with it. Technical safety Please observe the
instructions in “Installation” and “Technical data”. Before setting up the
washing machine, check it for any externally visible damage. Do not install or
use a damaged machine. Before connecting the washing machine, ensure that the
connection data on the data plate (fuse rating, voltage and frequency) match
the mains electricity supply. If in any doubt, consult a qualified
electrician.
6
Warning and Safety instructions Temporary or permanent operation on an
autonomous power sup-
ply system or a power supply system that is not synchronised with the mains
power supply (e.g. island networks, back-up systems) is possible. A
prerequisite for operation is that the power supply system complies with the
specifications of EN 50160 or an equivalent standard. The function and
operation of the protective measures provided in the domestic electrical
installation and in this Miele product must also be maintained in isolated
operation or in operation that is not synchronised with the mains power
supply, or these measures must be replaced by equivalent measures in the
installation. As described, for example, in the current version of BS OHSAS
180012 ISO 45001. The electrical safety of this washing machine can only be
guaranteed when correctly earthed. It is essential that this standard safety
requirement is met. If in any doubt, please have the wiring system of the
building tested by a qualified electrician. Miele cannot be held liable for
the consequences of an inadequate earthing system (e.g. electric shock). Do
not connect the washing machine to the mains electricity supply by a multi-
socket adapter, extension lead or similar. These do not guarantee the required
safety of the machine (fire hazard due to the risk of overheating). Faulty
components must only be replaced by genuine Miele original spare parts. Only
when these parts are fitted can Miele guarantee the safety standards of the
machine. The electrical socket must be easily accessible after installation so
that the machine can be disconnected from the electricity supply if necessary.
7
Warning and Safety instructions Unauthorised repairs could result in
unforeseen dangers for the
user, for which the manufacturer cannot accept liability. Repairs should only
be undertaken by a Miele authorised service technician, otherwise any
subsequent damage will not be covered by the warranty. While the washing
machine is under warranty, repairs should only be undertaken by a Miele
authorised service technician. Otherwise the warranty will be invalidated. If
the electrical connection cable is faulty it must only be replaced by a Miele
authorised service technician to protect the user from danger. The machine
must be isolated from the electricity supply when cleaning and maintaining the
machine and in the event of a fault. The machine must only be connected to the
on-site water supply using a new hose kit. Old hose kits must not be re-used.
Check the condition of the hoses regularly so that you can replace them in
good time and avoid the risk of any water damage. The water flow pressure must
be at least 100 kPa and should not exceed 1000 kPa. In areas which may be
subject to infestation by cockroaches or other vermin, pay particular
attention to keeping the machine and its surroundings in a clean condition at
all times. Any damage which may be caused by cockroaches or other vermin will
not be covered by the warranty. The machine must not be used in a non-
stationary location (e.g. on a ship). Do not make any alterations to the
machine, unless authorised to do so by Miele.
8
Warning and Safety instructions
Correct use Do not install the washing machine in a room where there is a risk
of frost. Frozen hoses may burst or split. The reliability of the electronic
control unit may be impaired at temperatures below freezing point. Before
using the machine for the first time, check that the transit bars at the rear
of the machine have been removed (see “Installation – Removing the transit
bars”). During spinning, a transit bar which is still in place may result in
damage to both the machine and adjacent furniture or appliances. Turn off the
stopcock if the machine is to be left for any length of time (e.g. holiday),
especially if there is no floor drain (gully) in the immediate vicinity.
Flooding danger. If hooking the drain hose into a wash basin, check that the
water can drain off quickly enough to prevent the sink from overflowing. Make
sure the drain hose is secure, so that the force of the water flowing out of
the hose does not dislodge it. Take care to ensure that foreign objects (e.g.
nails, pins, coins, paper clips) do not find their way into the machine with
the laundry. These may damage components of the machine (e.g. suds container,
drum), which in turn can result in damage to the laundry. Take care when
opening the drum door after using the steam function. Danger of burning due to
escaping steam and the high temperature of the surface of the drum as well as
the porthole glass. Stand back away from the machine and wait until the steam
has dissipated. The maximum load for this washing machine is 8.0 kg (dry
weight). See the “Programme chart” for the maximum recommended loads for
individual programmes.
9
Warning and Safety instructions If the correct amount of detergent is
dispensed, the machine
should not need to be descaled. If, however, you do wish to descale it, only
use a proprietary natural citric acid based descaling agent. Miele recommends
using Miele descaling agent which is available to order online at
www.miele.co.uk or from Miele. Strictly observe the instructions on the
packaging. Textiles which have been pre-treated in solvent based cleaning
agents must be thoroughly rinsed in clean water before being washed in the
machine. Do not use solvent based cleaning agents, e.g. those containing
benzine, in this machine, as this may result in damage to component parts and
create toxic fumes. Such agents also pose a fire and explosion hazard. Do not
use solvent based cleaning agents, e.g. those containing benzine, to clean the
surfaces of the machine. They can cause damage to plastic surfaces. Only use
dyes specified by the manufacturer as being suitable for use in a domestic
washing machine. Always observe the manufacturer’s instructions carefully.
Colour run and dye removers contain sulphur compounds which can cause damage
such as corrosion. Do not use these products in this machine. If detergent
comes into contact with the eyes, rinse them thoroughly with lukewarm water
immediately. If swallowed, seek medical assistance immediately and retain the
packaging or label for reference. Those with skin problems or sensitive skin
should avoid their skin coming into contact with detergent.
10
Warning and Safety instructions Accessories and spare parts Only use original
Miele accessories. If other parts are used, war-
ranty, performance and product liability claims will be invalidated. A Miele
tumble dryer can be stacked on top of a Miele washing machine using the
appropriate stacking kit (available as an optional accessory). Please make
sure you order the correct one for the Miele washing machine and Miele tumble
dryer. If installing the machine on a Miele plinth, (available as an optional
accessory, depending on country), please make sure you order the correct one
for this washing machine. Miele will guarantee to supply functional spare
parts for a minimum of 10 years and up to 15 years following the
discontinuation of your washing machine.
Miele cannot be held liable for damage caused by non-compliance with these
Warning and Safety instructions.
11
Operating the washing machine
Control panel
a Control field The control field consists of a time display and various
sensor controls. The individual sensor controls are explained in the following
sections.
b Sensor controls temperature for selecting the temperature.
c Sensor controls spin speeds for selecting the spin speed.
d Sensors for extra options You can supplement wash programmes with extra
options. If a wash programme has been selected, the sensor controls for the
possible Extras light up dimly.
e Indicator lights lights up if there are faults affecting the water inlet and
drainage lights up if excess detergent was used lights up as a reminder about
hygiene information The Add laundry function cannot be selected.
f Sensor controls CapDosing CapDosing of fabric care products (e.g. fabric
conditioner, proofing agent) CapDosing of additives (e.g. detergent enhancer)
CapDosing of detergent (for the main wash only)
12
Operating the washing machine
g Time display After the programme has started, the programme duration will
appear in the display in hours and minutes. When Delay start is being used,
the programme duration will appear after the Delay start time has elapsed.
h Sensor controls The Delay start time selected will appear in the time
display. After the programme has started, the Delay start time will begin to
count down. Once the Delay start time has elapsed, the programme begins and
the estimated programme duration appears on the time display. After touching
the sensor control, a later start time for the programme (Delay start) can be
selected. Once selected, lights up brightly.
The duration of the Delay start period is increased by touching the sensor
control.
The duration of the Delay start period is reduced by touching the sensor
control.
i Start/Add laundry sensor control The programme can be started as soon as the
sensor control is flashing on and off. Touching the Start/Add laundry sensor
control starts the selected programme. The sensor control lights up
constantly.
Once the programme has been started, the Start/Add laundry sensor control
allows you to add laundry.
j Optical interface This is used by the Service department as a transmission
point.
k Programme selector for selecting programmes and for switching off the
appliance. The washing machine is switched on when you select a programme, and
switched off by turning the programme selector to the position.
How the control field works
The , , , , and sensor controls react to fingertip contact. If a sensor
control is illuminated, it can be selected. If a sensor is brightly lit, this
means: currently selected If a sensor is dimly lit, this means: it can be
selected
13
Caring for the environment
Disposal of the packing material
The packaging is designed to protect the appliance from damage during
transportation. The packaging materials used are selected from materials which
are environmentally friendly for disposal and should be recycled. Recycling
the packaging reduces the use of raw materials in the manufacturing process
and also reduces the amount of waste in landfill sites.
Disposing of your old appliance
Electrical and electronic appliances often contain valuable materials. They
also contain specific materials, compounds and components, which were
essential for their correct function and safety. These could be hazardous to
human health and to the environment if disposed of with your domestic waste or
if handled incorrectly. Please do not, therefore, dispose of your old
appliance with your household waste.
Please dispose of it at your local community waste collection / recycling centre for electrical and electronic appliances, or contact your dealer or Miele for advice. You are also responsible for deleting any personal data that may be stored on the appliance being disposed of. Please ensure that your old appliance poses no risk to children while being stored prior to disposal.
14
Before using for the first time
Damage resulting from incorrect
installation and connection. Installing and connecting the washing machine
incorrectly will cause serious property damage. See “Installation”.
Removing the protective foil and stickers
Remove: – Any protective film from the door – Any stickers from the front and
the lid
Please do not remove any labels (e.g. the data plate) which are visible when
you open the door.
Shut the door with a gentle swing. This washing machine has undergone a complete functional test at the factory and there will be some residual water in the drum from this process.
Remove the drain hose elbow from the drum
An elbow piece for the drain hose is stored in the drum.
Pull open the door. Remove the elbow piece.
15
Before using for the first time
Running the first programme
For optimum water and energy consumption and excellent wash results, it is
important to calibrate the washing machine. To do this, the Cottons programme
must be run without laundry and without detergent. Open the stopcock.
Opening the door at the end of the programme
The door remains locked during the anti-crease phase. The control field lights
up for the first 10 minutes. The control field then goes out and the Start/Add
laundry sensor control flashes. Turn the programme selector to the
position. appears on the timer display and the indicator light goes out. The
door unlocks. Tip: After the anti-crease phase, the washing machine will have
switched off and the door unlocked automatically. The control field will be
completely dark.
Turn the programme selector to the Cottons position.
The washing machine is now switched on and in the control field, the
temperature 60 °C lights up. Touch the Start/Add laundry sensor
control. The programme will start.
After 10 minutes, the indicators dim, except for the Start/Add laundry sensor
control.
Take hold of the door and pull it open.
Tip: Leave the door slightly open to allow the drum to dry. Initial
commissioning is now complete.
16
Washing environmentally and economically
Energy and water consumption
– To get the most out of your machine, load the maximum dry load size for the
wash programme you are using. This will keep the energy and water consumption
to a minimum in relation to the size of the load.
– Programmes that are more efficient with regard to energy and water
consumption generally have a longer running time. By extending the programme
running time, the wash temperature that is actually reached can be reduced
while still providing the same wash results. For example, the ECO 40-60
programme has a longer running time than the Cottons 40 °C or 60 °C programme.
The ECO 40-60 programme is more efficient in terms of energy and water
consumption but has a longer running time.
– Use the Express 20 programme for small, lightly soiled loads.
– Modern detergents make it possible to wash at lower temperatures (e.g. 20
°C). Using lower temperature settings will save energy.
Hygiene in the washing machine
Washing at low temperatures and/or using liquid detergents can cause bacteria
and odours to build up in the washing machine. Miele therefore recommends
cleaning the washing machine once every month. When the indicator light
appears in the control field, the washing machine must be cleaned.
Information about subsequent tumble drying
The spin speed selected affects the residual moisture in the laundry and the
sound emissions of the washing machine. The higher the spin speed, the lower
the residual moisture in the laundry. However, the sound emissions of the
washing machine will increase. Select the highest possible spin speed for the
wash programme to save energy in the subsequent tumble dryer cycle.
Detergent
– Do not exceed the amounts of detergent recommended by the manufacturer on
the packaging.
– Adjust the dosage to the degree of soiling of the laundry.
– Reduce the amount of detergent with smaller loads (approx. less than the
amount recommended can be used when washing a half load).
17
1. Prepare the laundry
Tip: Stains (e.g. blood, egg, coffee, tea) can be pre-treated using some handy tricks which can be found in the Miele guide to laundry care.
Empty all pockets.
Damage due to foreign objects.
Nails, coins, paper clips, and so on can cause damage to garments and
components in the machine. Check the laundry before washing and remove any
foreign objects.
Sort the laundry Sort the laundry by colour and by
care label. Most garments have a textile care label in the collar or side
seam. Tip: Dark textiles often contain excess dye and should be washed
separately several times before being included in a mixed load. Always wash
whites and coloureds separately.
Pre-treating stains Badly soiled areas and stains should
be cleaned as soon as possible, preferably whilst still fresh. Spillages
should be carefully dabbed off using a soft, colourfast cloth. Do not rub.
Damage due to solvent-based
cleaning agents Cleaning agents containing benzine, stain remover, etc., can
damage plastic parts. When pre-treating textiles, make sure that any plastic
parts (e.g. buttons) do not come into contact with cleaning agent.
Risk of explosion due to solvent-
based cleaning agents. When using solvent-based cleaning agents, an explosive
mixture may develop. Never use solvent-based cleaning agents in the washing
machine.
General tips – Curtains: Remove lead weights first
or place in a laundry bag. – Underwiring and collar stiffeners: Any
loose wiring in bras, shirt collar stiffeners, etc. should be removed or sewn
in. – Close any zips, attach velcro fasteners, fasten hooks and eyes etc.
before washing. – Fasten duvet covers, pillow cases etc. to prevent small
items from being rolled up inside them. Do not wash any items in this washing
machine which are specified by the manufacturer as not washable on the care
label ( symbol).
18
Open the door
2. Load the washing machine
Close the door
Take hold of the door and pull it open. Check the drum for pets or foreign
objects before loading it with laundry.
The most efficient use of energy and water is achieved when a full load is
washed. However, do not overload as this reduces cleaning efficiency and
causes creases. Unfold the laundry and load loosely
into the drum. Mixing both large and small items gives better wash results and
also helps distribute the load evenly during spinning. Tip: Please note the
maximum load for different wash programmes.
Make sure that no items are caught between the door and the seal.
Shut the door with a gentle swing.
19
3. Select a programme
Programme selection
The washing machine is switched on by turning the programme selector to a wash
programme.
Selecting a temperature and spin speed The wash programme’s preset temperature and spin speed light up brightly. The choice of available temperatures and spin speeds for the wash programme light up dimmed. The temperatures reached inside the washing machine might not be the same as the temperatures selected. Perfect wash results are achieved through a combination of energy use and wash duration.
Turn the programme selector to the required programme.
The likely wash time is shown in the time display and the pre-set temperature
and spin speed light up in the control panel.
Touch the sensor for the desired temperature. It will then light up brightly.
Touch the sensor for the desired spin speed. It will then light up brightly.
20
Selecting Extras The selection of extras available for the wash programme lights up dimly.
3. Select a programme
Touch the sensor for the extra you want. It then lights up brightly.
Tip: You can select multiple extras for a wash programme. Please refer to
“Extras” for more information.
21
4. Add detergent
Detergent dispenser drawer
Any detergent suitable for automatic front loading washing machines can be
used. Please observe the instructions for use and dosage on the detergent
packaging.
Adding detergent
Adding fabric conditioner
Pull out the detergent drawer and add detergent to the compartments.
Detergent for the pre-wash Detergent for the main wash Fabric softener, liquid
starch or capsules
Add fabric conditioner or liquid starch to the compartment. Do not exceed the
maximum level mark.
It will be automatically dispensed in the final rinse. At the end of the
programme a small amount of water remains in the compartment.
If starching frequently, thoroughly clean the dispenser compartment,
especially the siphon tube, regularly.
22
4. Add detergent
Tips on dosing Adjust the detergent dosage to the level of soiling of the
laundry and the size of the load. Reduce the amount of detergent with smaller
loads (e.g. reduce the amount of detergent by when washing a half load). Too
little detergent: – Results in laundry not being cleaned
properly and may cause it to become grey and hard to the touch over time. –
Can lead to a build-up of mould in the washing machine. – Results in grease
not being completely removed from the laundry. – Can lead to limescale
deposits on the heater elements. Too much detergent – Causes poor wash, rinse,
and spin results. – Causes higher water consumption as an extra rinse cycle is
automatically activated. – Is a greater burden on the environment.
Using liquid detergent with a prewash Liquid detergent cannot be used for the
main wash if the pre-wash has been selected. Use powder detergent for the main
wash.
Using detergent tablets or pods Always put detergent tablets or pods directly
in the drum with the laundry. They cannot be added via the detergent dispenser
drawer. See “Detergent” for further information.
23
4. Add detergent
CapDosing
Three different types of capsule are available:
= Fabric care (e.g. fabric conditioner, proofing agent)
= Additives (e.g. detergent enhancer)
= Detergent (for the main wash only)
Each capsule contains the correct amount for one wash cycle. Caps are
available to order from Miele or from the Miele online shop (see the end of
this booklet for contact details).
Capsules pose a health risk.
The ingredients of capsules can be hazardous to health if they are swallowed
or come into contact with skin. Keep capsules out of the reach of children.
Inserting a capsule
Open the detergent dispenser drawer.
Open the lid of the / compartment.
Activating CapDosing
Touch the sensor for the capsule you want to use.
Sensor control
for
for
for
Capsule
Press the capsule in firmly.
24
4. Add detergent
Close the lid and press it firmly shut. Close the detergent dispenser
drawer.
The capsule is opened by the act of inserting it in the detergent dispenser
drawer. The contents can run out of the capsule if you then remove it from the
drawer before it is used. Dispose of opened capsules.
The wash programme will dispense the contents of the capsule at the correct
time.
Water intake to the compartment is solely via the capsule. Do not add any
additional fabric conditioner to the compartment.
Remove the empty capsule at the end of the programme.
For technical reasons a small amount of water will remain in the capsule.
Switching off/changing CapDosing
In order to switch off CapDosing, touch the brightly lit sensor.
In order to change CapDosing, touch one of the other capsule sensors.
25
5. Start the programme
Starting a programme
Adding laundry during a programme sequence (AddLoad)
Laundry can be added or removed at any time, provided that the symbol is not illuminated on the control field.
Touch the flashing Start/Add laundry sensor control.
The door locks and the programme starts. If a Delay start time has been
selected, this counts down on the time display. At the end of the Delay start
time or immediately after the programme has started, the programme duration
appears on the time display.
Energy savings After 10 minutes, the indicators dim. The sensor control
Start/Add laundry flashes. To reactivate the indicators: Touch the Start/Add
laundry sensor
control (this does not have any effect on a programme that is running).
Touch the Start/Add laundry sensor control.
Rotating bars … … are shown on the time display. If the word appears on the
time display, the door can be opened. Open the door and add or remove
laundry. Close the door. Touch the Start/Add laundry sensor
control. The programme will continue. Laundry cannot usually be added or
removed if: – The suds temperature is above 55 °C – The water inside the drum
is above a
certain level
26
Opening the door and removing the laundry
The door remains locked during the anti-crease phase. The control field lights
up for the first 10 minutes. The control field then goes out and the Start/Add
laundry sensor control flashes. Turn the programme selector to the
position. appears on the timer display and the indicator light goes out. The
door unlocks. Tip: After the anti-crease phase, the door will have unlocked
automatically.
6. End of programme
Items left in the drum could discolour other items in the next wash or become
discoloured themselves. Remove all items from the drum.
Check the door seal for any foreign objects.
Tip: Leave the door slightly open to allow the drum to dry. If applicable,
remove the used cap-
sule from the detergent drawer. Tip: Leave the detergent drawer slightly open
to allow it to dry.
Take hold of the door and pull it open.
Remove the laundry.
27
Spinning
Final spin speed in wash programmes
When a programme is selected, the sensor control for the optimum spin speed
for that programme will be brightly lit up in the control field. A faster spin
speed can be selected for certain wash programmes. The highest selectable spin
speed is indicated in the table.
Programme Cottons Cottons Minimum iron Delicates Woollens Shirts QuickPowerWash Express 20 ECO 40-60 Proofing Drain/Spin Separate rinse/Starch
rpm 1400 1400 1200 900 1200 900 1400 1200 1400 1200 1400 1200
Rinse and interim spin
There is a spin after the main wash and between the rinses. A reduction in the
final spin speed will also reduce the interim spin speed. If a spin speed of
less than 700 rpm is selected for the Cottons programme, an additional rinse
is introduced.
Selecting Rinse hold (final spin)
Touch the sensor control (Rinse hold).
The laundry is not spun after the final rinse and remains in the rinse water.
This helps to prevent creasing if the laundry is not going to be removed from
the drum immediately after the end of the programme.
Ending a programme with a spin cycle The sensor control for the optimum spin
speed lights up on the control field. You can change the spin speed. Touch the
Start/Add laundry sensor
control.
Ending a programme without a spin cycle Reduce the spin speed to 0. Touch the
Start/Add laundry sensor
control.
To omit rinse and interim spin and the final spin
Touch the sensor. After the last rinse, the water will be pumped away and the
anti-crease phase will switch in. In some programmes an additional rinse is
introduced with this setting.
28
Delay start
With Delay start you can choose when you want the programme to start. You can delay the start of the programme by 30 minutes up to a maximum of 24 hours, allowing you to make use of night-time economy electricity rates, for example. Selecting Delay start Delay start is not possible in the Drain/ Spin and Proofing programmes. Select the programme required. Touch the sensor control.
Starting Delay start Touch the flashing Start/Add laundry
sensor control. The Delay start process starts and counts down on the time
display.
Changing or cancelling a started Delay start If the selected Delay start
function has started, it is no longer possible to change the time. Turn the
programme selector to the
position. Turn the programme selector to any
programme. Rotating bars … … or are shown on the time display. The door lock
is released. Select a programme and a new Delay
start time.
The sensor control lights up brightly. Touch the or sensor control re-
peatedly until the required Delay start time appears on the time display. – In
the case of settings below 10 hours, the Delay start time changes in
increments of 30 minutes – In the case of settings above 10 hours, the Delay
start time changes in increments of 1 hour
29
Programme chart
Cottons
60 °C/40 °C
Max. load 8,0 kg
Items
Normally soiled cotton garments
Tip
– These settings are the most efficient in terms of energy and water
consumption for washing cottons.
– With 60 °C, the wash temperature reached is below 60 °C. The wash performance is the same as with the Cottons 60 °C programme.
Note for test institutes: The test programme conforms to EN 60456 and the energy label to Directive 1061/2010.
Cottons
90 °C to cold
Max. load 8,0 kg
Items
Cotton, linen or mixed fibre fabric, e.g. table linen, underwear, Tshirts, etc.
Tip
Where particularly high levels of hygiene are required, please select
a temperature of 60 °C or higher.
Minimum iron
Cold to 60 °C
Max. load 3.5 kg
Items
Synthetic and mixed fibre textiles as well as easy care cotton
Tip
Reduce the spin speed for fabric that creases easily.
30
Programme chart
Delicates
Cold to 40 °C
Max. load 2.0 kg
Items
Delicate garments made from synthetic fibre, mixed fibre and viscose Performance outerwear (e.g. jackets and trousers) made from membrane fabric such as Gore-Tex®, SYMPATEX®, WINDSTOPPER®, etc. Curtains specified as machine-washable by the manufacturer.
Tip
– On outdoor clothing, fasten zips or close Velcro fasteners and do
not use fabric conditioner.
– If required, these items can also be re-proofed using the Proofing programme. Proofing after each wash cycle is not recommended.
– Dust in curtains usually means that a programme with Pre-wash is advisable.
– Deselect the spin speed for items which crease easily.
Woollens
Cold to 40 °C
Max. load 2.0 kg
Items
Wool or wool blend fabric
Tip
Reduce the spin speed for fabric that creases easily.
Shirts
Cold to 60 °C
Max. load 1.0 kg/2.0 kg
Items
Shirts and blouses made of cotton and mixed fibre
Tip
– Pre-treat collars and cuffs depending on the level of soiling.
– Wash silk shirts and blouses in the Delicates programme.
– If the preset Pre-ironing extra is switched off, the maximum load capacity is increased to 2.0 kg.
31
Programme chart
QuickPowerWash
60 °C 40 °C
Max. load 4.0 kg
Items
Lightly to moderately soiled garments which are also suitable for washing in the Cottons programme
Tip
A special saturation process and wash rhythm ensure that the laun-
dry is cleaned particularly quickly and thoroughly.
Express 20
Cold to 40 °C
Max. load 3.5 kg
Items
Cotton garments that have hardly been worn or are only very lightly soiled
Tip
The Short extra option is activated automatically.
ECO 40-60
Max. load 8.0 kg
Items
For normally soiled cotton garments
Tip
A laundry load consisting of mixed cottons that are intended for
washing at 40 °C or 60 °C can be washed in the same wash cycle.
This programme is the most efficient in terms of energy and water consumption for washing cottons.
Note for test institutes:
Test programme for compliance with EU legislation regarding ecodesign No. 2019/2023 and energy labelling in accordance with Regulation No. 2019/2014.
Proofing
40 °C
Max. load 2.5 kg
Items
Treating microfibre fabric, ski wear or table linen made from mainly synthetic fibres to provide a finish which is resistant to water and dirt
Tip
– The items must be freshly laundered and spun or dried before
proofing.
– For best results, the items should be heat-treated afterwards. This can be achieved by drying them in the tumble dryer or ironing them.
32
Programme chart
Drain/Spin
Tip
– Drain only: Set spin speed to .
– Make sure you select the appropriate spin speed.
Separate rinse/Starch
Max. load 8.0 kg
Items
– Rinsing hand-washed items
– Table cloths, serviettes and workwear requiring starching
Tip
– Reduce the spin speed for fabric that creases easily.
– Laundry that is to be starched should be washed but not treated with fabric conditioner.
– Items will be rinsed very effectively with 2 rinses by activating the Water
- extra.
33
Extra options
You can use the extra options buttons to augment the wash programmes. Extras are selected and deselected using the relevant sensors on the control panel.
Water +
The water level in the main wash and the rinses will be increased. A second
rinse cycle is carried out in the Separate rinse/Starch programme. You can
select other functions for the Water + sensor control. These are described
under “Programmable functions”.
Pre-wash
For laundry with large amounts of dirt, e.g. dust and sand.
Touch the sensor for the extra you want.
The relevant sensor will light up brightly. Not all the extra options are
suitable for use with every programme. An extra that is not permitted for the
wash programme is not lit dimly and cannot be activated by touch.
Short
For textiles with light soiling with no visible staining. The wash duration is
reduced.
Pre-ironing
In order to reduce creasing, the laundry undergoes a smoothing process at the
end of the programme. Reducing the maximum load by 50 % will achieve a better
result. Small loads achieve a better result. The garments must be suitable for
drying in a tumble dryer and suitable for ironing .
34
Extra options
The following extras can be selected in addition to the programmes
Short Water + Pre-wash Pre-ironing
Cottons Cottons Minimum iron Delicates Woollens Shirts QuickPowerWash Express
20 ECO 40-60 Proofing Separate rinse/Starch
= can be selected = cannot be selected
= activated automatically
35
Programme sequence
Cottons Cottons Minimum iron Delicates Woollens Shirts QuickPowerWash Express 20 ECO 40-60 Proofing Drain/Spin Separate rinse/Starch
Main wash
Water level
Wash rhythm
Rinses
Water level
Rinses
2-52,3
2-51,2,3
2-42,3
2-42,3
2
3-43
2
1
232
1
0-15
Please see the next page for a description of the symbols.
Spinning
36
Programme sequence
= low water level = medium water level = high water level = intensive rhythm =
normal rhythm = sensitive rhythm = handwash rhythm = carried out = not
carried out
This washing machine has fully electronic controls with automatic load
control. The washing machine takes in the right amount of water required for
the programme depending on the amount of laundry and its absorbency rate. The
programme sequences outlined in the chart are based on the basic programme
with a full load.
Special features in the programme sequence
Anti-crease: At the end of the programme, the drum continues to turn at
intervals for up to 30 minutes to help prevent creasing. Exception: there is
no anti-crease phase in the Woollens programme. The washing machine can be
opened at any time.
- If a temperature of 60 °C or higher is selected, two rinses are carried
out. If a temperature of less than 60 °C is selected, three rinses are carried
out.
2 An additional rinse is carried out if:
– there is too much foam in the drum
– a spin speed lower than 700 rpm has been selected.
3 An additional rinse is carried out if:
– the Water + extra option has been selected and the options or have been activated in Programmable functions.
5 An additional rinse is carried out if: the Water + extra option has been selected.
37
Programme sequence
PowerWash
PowerWash is a washing technique developed by Miele. It is activated in the
following programmes: – Cottons (with small and medium-
sized loads) – Minimum iron – Shirts – Delicates – ECO 40-60 (with small and
medium-
sized loads)
How it works Conventional washing techniques wash with more water than the
laundry can absorb. This total volume of water needs to be heated. The
PowerWash washing technique only uses slightly more water than the laundry can
absorb. The water which has not been absorbed by the laundry heats up the drum
and the laundry and is sprayed into the laundry over and over again. This
reduces energy consumption.
Activation PowerWash is activated automatically in the programmes listed
above. PowerWash is deactivated if: – The selected final spin speed is less
than 600 rpm – CapDosing (, ) has been selec-
ted for the main wash – The wash temperature is higher than
60 °C – Extras such as Pre-wash or Water +
have been selected – A large load is being washed in the
Cottons programme
Special features – Drenching phase
The washing machine will spin a few times at the beginning of the programme.
During spinning, the water discharged is sprayed back into the laundry in
order to achieve optimum moisture penetration. The optimum water level is set
at the end of the drenching phase. If necessary, the washing machine will pump
water away or take in a little more fresh water. – Noises during the heating
phase Unusual bubbling noises can occur while the laundry and the drum are
being heated.
38
Changing the programme sequence
Changing a programme (safety lock)
A programme, temperature, spin speed or selected options cannot be changed
once the machine has been successfully started. This prevents the machine
being operated unintentionally, e.g. by children.
If the washing machine is switched off during active programme operation, the
standby function does not switch the washing machine off completely after 15
minutes. Safety functions continue to be active because there may still be
water inside the drum.
Cancelling a programme
You can cancel a programme at any time after it has started. Turn the
programme selector to the
position. Turn the programme selector to any
position. Rotating bars … … or are shown on the time display. The water is
pumped away and the door lock is then released.
Selecting a new programme Turn the programme selector to the
required programme. Check that there is still detergent in
the detergent drawer. Add more detergent if there is none left. Touch the
Start/Add laundry sensor control.
39
Garment care label symbols
Washing The figure quoted in the bucket is the maximum temperature at which the garment can be washed. Normal agitation Reduced agitation Much reduced agitation Hand wash Do not wash
Programme selection examples
Programme
Cottons Minimum iron Delicates Woollens Express 20
Garment care label symbols
Drying Normal temperature Low temperature Do not tumble dry
Ironing Approx. 200 °C Approx. 150 °C Approx. 110 °C
Ironing with steam can cause irreversible damage. Ironing/rotary ironing
prohibited
Professional cleaning
Dry clean only. The letters indic-
ate the type of cleaning agent required.
Wet cleaning
Dry cleaning prohibited
Bleaching Any oxidation bleach can be
used Use oxygen bleach only Do not bleach
40
Detergent
The correct detergent
All detergents produced for automatic washing machines are suitable. Follow
the manufacturer’s instructions and dosage recommendations on the packaging.
For users in Asia: please use a low foaming detergent suitable for use in
front-loading machines
The right amount to dispense will depend on the following:
– the soiling level of the load – the quantity of the laundry – the water
hardness level.
Check with your local water supplier if you do not know the hardness level in
your area.
Water softeners
A water softener can be used to cut down on the use of detergents in areas
with water hardness levels II and III. Dispense according to the amount
specified on the packaging. First add detergent and then the water softener.
You can then use the recommended amount of detergent for water hardness level
I.
Dispensing aids
Use dispensing aids, (e.g. balls) if these are supplied with the detergent,
particularly when using liquid detergent.
Refill packs of detergent
When purchasing detergent buy refill packs wherever possible. This helps
reduce the amount of waste packaging.
Fabric conditioner and liquid starch
Fabric conditioner makes garments soft to handle and helps prevent static
cling when tumble drying. Starch stiffens and gives body to items of laundry,
e.g. shirts, tablecloths and bed linen.
Water hardness levels
Hardness scale I (soft)
II (medium) III (hard)
Hardness level German scale
in mmol/l
°d
0 1.5
0 8.4
1.5 2.5
8.4 14
above 2.5
above 14
41
Detergent
Using fabric conditioner or starch separately
Prepare the starch in accordance with the manufacturer’s instructions on the
packaging. Tip: When adding fabric conditioner, activate the Water + extra.
Add fabric conditioner to the com-
partment or insert the appropriate capsule. Add liquid starch to the
compartment and powder or viscous starch to the compartment. Select the
Separate rinse/Starch programme. Change the spin speed if necessary. Activate
the Cap sensor control if using a capsule. Touch the Start/Add laundry sensor
control.
Colour run and dye removers/ dyes
Damage due to colour run/dye
removers. Colour run and dye removers can cause corrosion in the washing
machine. Do not use colour run or dye removers in this washing machine.
Dyes suitable for use in domestic washing machines can be used. However,
please note that the salt used in the dyeing process can cause corrosion to
stainless steel components in the machine if you use dye frequently. Always
follow the dye manufacturer’s instructions carefully.
When using the machine to dye fabric, it is essential to select the Water +
extra.
42
Detergent
Recommended Miele detergents
Miele detergents have been specially designed for day-to-day use in Miele
washing machines. See “Detergents and care products” for more information
about these detergents.
Cottons Cottons Minimum iron Delicates Woollens Shirts QuickPowerWash Express 20 ECO 40-60 Proofing Separate rinse/Starch
Miele detergents
UltraWhite UltraColor
/
/
Miele capsules
/
/
/
Recommendation No recommendation
Specialist detergents (e.g. WoolCare) Fabric care (e.g. fabric conditioner) Additive (e.g. booster)
43
Detergent
Recommended detergents in accordance with Directive (EU) Nr. 1015/2010
The recommendations apply to the temperature ranges given in the Programme
chart.
Cottons Cottons Minimum iron Delicates Woollens Shirts QuickPowerWash Express
20
ECO 40-60
Universal
Coloureds Delicates and woollens
detergent
1
Specialist
Recommendation No recommenda-
tion
1
Liquid detergent
2
Powder detergent
44
Cleaning and care
Cleaning the external casing and the control panel
Risk of electric shock!
Mains voltage is present when the washing machine is switched off Disconnect
the machine from the electricity supply before cleaning or maintenance.
Risk of damage due to ingress of
water. The pressure of a water jet can cause water to get into the washing
machine, resulting in damage to components. Do not spray the washing machine
with a water jet.
Cleaning the detergent dispenser drawer
Washing at low temperatures and the use of liquid detergent can lead to a
build-up of mould and bacteria in the detergent dispenser drawer. For hygiene
reasons, clean the entire
drawer at regular intervals. Removing the dispenser drawer
Clean the casing and control panel with a mild cleaning agent or soap and
water and dry both with a soft cloth.
The drum can be cleaned using a suitable stainless steel cleaning agent
following the manufacturer’s instructions on the packaging.
Damage caused by cleaning
agents. Solvent based cleaning agents, abrasive cleaners, glass cleaners or
multi-purpose cleaning agents can cause damage to plastic surfaces and other
parts. Do not use any of these cleaning agents.
Pull out the detergent dispenser drawer until a resistance is felt. Press down
the release button and at the same time pull the drawer right out of the
machine.
Clean the detergent drawer with warm water.
45
Cleaning and care
Cleaning the siphon and the / compartment channel
Liquid starch results in clogging. If clogged, the siphon in the / compartment
will not work and the compartment can overflow. Clean the siphon particularly
thoroughly after using liquid starch a few times.
Clean the fabric conditioner channel using a brush and warm water.
Cleaning the detergent dispenser drawer compartment
1. Remove the siphon from compartment and clean under warm running water.
Clean the siphon tube in the same way.
2. Replace the siphon.
Use a bottle brush to remove detergent residues and limescale from the jets
inside the detergent dispenser drawer compartment.
Replace the detergent dispenser drawer.
Tip: Leave the detergent dispenser drawer slightly open to allow it to dry.
46
Cleaning and care
Hygiene info (Cleaning the drum)
Washing at low temperatures and/or using liquid detergent can cause bacteria
and unpleasant odours to build up in the washing machine. Use the Cottons 90
°C programme to clean the washing machine. Clean the drum when the indicator
light comes on at the latest.
Clean the filter. Reassemble in reverse order.
Cleaning the filter in the inlet valve Using pliers, carefully loosen the
ribbed plastic nut on the inlet valve and unscrew it.
Cleaning the water inlet filter
The washing machine has 2 filters to protect the inlet valve. Check these
filters every 6 months or so. Perform this check more often if there are
frequent interruptions to the external water supply.
Cleaning the filter in the inlet hose First turn off the stopcock. Unscrew the
inlet hose from the stop-
cock.
Use pointed pliers to withdraw the plastic filter by the slat.
Clean the filter. Reassemble in reverse order.
The two filters must be put back in place after cleaning.
Screw the screw connection securely back onto the stopcock.
Open the stopcock.
Make sure there is no water leaking from the threaded union. Tighten the threaded union.
Remove the rubber seal 1 from the recess.
Using pointed pliers, take hold of the plastic filter slat 2 and remove the
plastic filter. 47
Problem solving guide
Many malfunctions and faults that can occur in daily operation can be easily remedied. Time and money will be saved because a service call will not be needed. The following guide may help you to find the reason for a malfunction or a fault, and to correct it.
The programme does not start
Problem The control panel remains dark.
and alternately appear in the time display.
Cause and remedy
There is no power to the machine. Check whether the mains plug is plugged in
and
switched on. Check whether the fuse or circuit breaker has
tripped.
The washing machine has switched off automatically to save energy. Switch the
washing machine on again by turning
the programme selector.
The door is not closed properly. The door lock could not engage. Close the
door again. Start the programme again.
If the fault message appears again, contact the Service Department.
48
Problem solving guide
The programme is cancelled and a fault indicator light lights up in the control panel
Problem
Cause and remedy
The fault indicator light lights up, and appear alternately in the time display and the buzzer sounds.
The water outlet is blocked or restricted. The drain hose has been fixed too
high.
Clean the drain filter and the drain pump. The maximum delivery head is 1 m.
The fault indicator light The water inlet is blocked or restricted.
lights up, and ap- Check whether the stopcock is opened properly.
pear alternately in the Check whether the inlet hose is kinked.
time display and the buzzer sounds.
Check whether the water pressure is too low.
The filter in the water inlet is blocked.
Clean the filter.
The fault indicator light The water protection system has reacted.
lights up, and Close the stopcock.
appear alternately in the time display and the
Call the Service Department.
buzzer sounds.
and appear altern- There is a fault. ately on the time display Disconnect the
washing machine from the electriand the buzzer sounds. city supply. Switch off
at the wall and withdraw the
plug from the socket, or disconnect the fuse.
Wait at least 2 minutes before reconnecting the washing machine to the
electricity supply.
Switch the washing machine on again. Restart the programme.
If the fault message appears again, contact the Miele Customer Service
Department.
49
Problem solving guide
During the programme, a symbol appears in the time display
Message lights up
Cause and remedy
The programme selector was moved to a different position after the programme
had started. Turn the programme selector back to the original
position.
At the end of the programme, an indicator light lights up in the control panel
Problem The indicator light lights up. The indicator light lights up.
and appear alternately on the time display.
Cause and remedy
Excessive foam has built up during washing. Use less detergent next time, and
follow the man-
ufacturer’s recommended dosage amounts on the packaging.
When washing, a wash programme using a temperature above 60 °C has not been
run for a long time. Run the Cottons 90 °C programme using Miele
machine cleaner or a universal powder detergent.
This will clean the washing machine and prevent a build-up of bacteria and
odours.
The Pre-ironing extra which runs at the end of the programme could not be
carried out properly. Check whether the washing machine is aligned
correctly (see “Installation Levelling the machine”). Check whether the
maximum drainage head height of 1 m has been exceeded.
If the fault message appears again, contact the Miele Customer Service
Department. The washing machine can still be used, but without the Pre-ironing
extra.
50
Problem solving guide
General problems with the washing machine
Problem
Cause and remedy
The washing machine smells.
The indicator light was ignored. A wash programme using a temperature above 60
°C has not been run for a long time. In order to prevent bacteria and
unpleasant odours
building up in the washing machine, run the Cottons 90 °C programme using
Miele machine cleaner or a universal powder detergent.
The door and the detergent dispenser drawer were left shut after washing.
Leave the door and the detergent dispenser
drawer slightly open to allow them to dry.
The machine shakes during the spin cycle.
The machine feet are not level. Level the machine and adjust the feet correctly.
The laundry has not been spun properly and is still wet.
The machine detected an imbalance during the final spin cycle and reduced the
spin speed automatically. Include both large and small items in the load as
this will give better distribution during spinning.
Strange pump noises can be heard.
This is not a fault. These slurping noises occur at the end of the pump sequence as a normal part of operation.
Large amounts of deter- The water pressure is too low.
gent residue remain in Clean the water inlet filter.
the detergent dispenser drawer.
It may be useful to select the Water + extra option. Powder detergent used in conjunction with water
softeners tends to become sticky.
In future, add washing powder into the dispenser drawer first, and then add the water softener.
51
Problem solving guide
General problems with the washing machine
Problem
Cause and remedy
Fabric conditioner is not The siphon tube is not correctly positioned or is
completely dispensed clogged.
or too much water remains in the com-
Clean the siphon, see “Cleaning and care – Cleaning the detergent dispenser drawer”.
partment.
At the end of the programme there is still liquid in the capsule.
The small pipe in the detergent dispenser drawer onto which the capsule is placed is blocked. Clean the small pipe.
This is not a fault. For technical reasons a small amount of water will remain in the capsule.
There is water next to The sensor control was not activated.
the capsule in the fabric Make sure that you remember to activate the
conditioner compart-
sensor control the next time you insert a cap-
ment
sule.
An empty capsule was not removed at the end of the last wash programme. Remove
and dispose of the empty capsule at the
end of each programme.
There is a blockage in the small pipe in the detergent drawer onto which the capsule is placed. Clean the small pipe.
52
Problem solving guide
An unsatisfactory wash result
Problem
Cause and remedy
Liquid detergent does not give the required result.
Liquid detergents usually contain no bleaching agents. They do not remove
fruit, coffee and tea stains. Use a general purpose powder detergent contain-
ing a bleaching agent. Use the appropriate capsule or add stain removers
to the compartment. Never put stain removers and liquid detergent to-
gether in the dispenser drawer.
Grey, greasy particles Insufficient amounts of detergent were used to break
cling to washed laundry. down the particles of grease in heavily soiled
laundry.
Use more detergent. Before washing the next load run a Cottons 60°C
programme with powder detergent but without a load.
White residues which look like powder detergent are seen on dark textiles after washing.
The detergent contained compounds (zeolites) to aid water softening which are
not soluble in water. These have ended up on the laundry. Try and brush off
the residues with a soft brush
once the laundry is dry. Wash dark textiles using a detergent which con-
tains no zeolites. Liquid detergents usually contain no zeolites.
53
Problem solving guide
The door will not open
Problem
Cause and remedy
The door cannot be pulled open during a programme.
The drum is locked during a programme. Follow the description in “5. Starting
a programme
Adding or removing laundry”.
After the programme is cancelled, flashing bars ……… appear in the time display.
For safety reasons the drum door cannot be opened if the suds temperature is
higher than 55 °C. Wait until the temperature in the drum has de-
creased and the bars have stopped flashing in the display.
and alternately ap- The door lock has jammed. pear in the time display. Call the Service Department.
54
Opening the door in the event of a blocked drain outlet and/ or power cut
Switch off the washing machine.
Problem solving guide
Draining the washing machine Remove the drain filter, though not completely.
Place a suitable container under the access panel, e.g. a universal oven tray.
Open the drain pump access panel.
Blocked drain outlet If the drain outlet is blocked, there may be a large
quantity of water left behind in the washing machine.
Risk of scalding due to hot suds.
Escaping suds will be hot if laundry has been washed at high temperatures!
Carefully allow all suds to drain off.
Slowly unscrew the drain filters to let the water out.
Tighten the drain filters back up again if you need to interrupt the flow of
water.
Once the flow of water ceases:
Remove the drain filters completely. 55
Problem solving guide
Open the door
Danger of injury due to rotating
drum! Reaching into a moving drum is extremely dangerous. Always make sure
that the drum is stationary before reaching in to remove laundry.
Clean the drain filters thoroughly. Remove any foreign objects (e.g. but-
tons, coins, etc.) and clean the interior. Turn the impellers by hand to check
that they rotate freely.
Use a screwdriver to unlock the door. Pull open the door.
Replace the drain filters correctly (on the right and left) and tighten them
securely.
Close the drain pump access panel.
Risk of water damage.
Make sure the drain filters are securely tightened. Otherwise there is a risk
of water leakage during use. Replace the drain filters correctly and tighten
them securely.
56
Service
Contact in the event of a fault
In the event of any faults which you cannot remedy yourself, please contact
your Miele dealer or the Miele Customer Service Department.
You can book a Miele Customer Service Department call-out online at
www.miele.com/service. Contact information for the Miele Customer Service
Department can be found at the end of this document. Please quote the model
identifier and serial number of your appliance (Fabr./ SN/Nr.) when contacting
the Miele Customer Service Department. This information can be found on the
data plate. Please note that telephone calls may be monitored and recorded for
training purposes and that a call-out charge will be applied to service visits
where the problem could have been resolved as described in this booklet. The
data plate is found above the porthole glass when the door is opened.
Optional accessories
Optional spare parts and accessories for this washing machine are available
from your Miele Dealer, the Miele Spare Parts Department or via the internet
at www.miele.co.uk. Please note that telephone calls may be monitored and
recorded for training purposes.
EPREL database
From 1 March 2021, information on energy labelling and ecodesign requirements
will be available in the European Product Database (EPREL). You can find the
product database at the following link https://eprel.ec.europa.eu/. You will
be asked to enter the model identifier. The model identifier can be found on
the data plate.
Made in xxx
Mod.: XXXxxx M-Nr.: xxxxxxxx Type: XXxx-X Nr.:/ xxxxxxxxx
Miele Service
www.miele.com/service
Warranty
For information on the appliance warranty specific to your country please
contact Miele. See back cover for address.
In the UK, your appliance warranty is valid for 2 years from the date of
purchase. However, you must activate your cover by calling 0330 160 6640 or
registering online at www.miele.co.uk.
57
INSTALLATION
Installation
Front view
a Water inlet hose (pressure tested to 7000 kPa)
b Mains connection cable c Flexible drain hose (with detachable
swivel elbow) d Control panel
e Detergent dispenser drawer f Door g Access to filters, pumps and emer-
gency release h Four height-adjustable feet
58
INSTALLATION
Rear view
Installation
a Drain hose b Transport clips for inlet and drain
hoses and mains connection cable c Mains connection cable d Protruding lid for
holding when mov-
ing the machine
e Water inlet hose (pressure tested to 7000 kPa)
f Safety caps for transit bars g Transport clips for inlet and drain
hoses and for storing transit bars when not in use
59
INSTALLATION
Installation
Installation surface
A concrete floor is the most suitable installation surface. It is far less
prone to vibration during the spin cycle than wooden floorboards or a carpeted
surface. Please note: The machine must be level and se-
curely positioned. To avoid vibrations during spinning,
the machine should not be installed on soft floor coverings. If installing on
a wooden joist floor: Install the machine on a plywood base (at least 59 x 52
x 3 cm). The base should span several joists and be bolted to the joists and
not only to the floorboards. Check for the presence of pipes and cables first.
Tip: If possible, install the machine in a corner. This is usually the most
stable part of the floor.
Injury can occur if the washing
machine has not been adequately secured. During installation, the washing
machine must be secured on a plinth to be made available on site (concrete or
brick), in order to ensure it cannot fall or slip. Secure the washing machine
using a clamp/fastening bracket (MTS floor mounting kit available from your
Miele dealer or Miele spare parts department).
Transporting the washing machine to its installation site
Danger of injury due to unsecure
lid. Make sure the fixings at the back of the lid are secure. Otherwise there
is a danger of the lid being pulled off when carrying the machine. Before
carrying the machine check that the lid is secure where it protrudes at the
back of the machine.
Carry the washing machine by the front feet and by the lid where it protrudes
at the back of the appliance.
60
INSTALLATION
Removing the transit bars
Removing the left-hand transit bar
Installation
Removing the right-hand transit bar
Push the cover out and turn the lefthand transit bar 90° using the spanner supplied.
Push the cover out and turn the lefthand transit bar 90° using the spanner supplied.
Withdraw the transit bar.
Withdraw the transit bar.
61
INSTALLATION
Installation
Covering holes
Risk of injury from sharp edges.
There is a risk of injury from reaching into holes that are not covered. Cover
the holes for the transit bars after they have been removed.
Securing the transit bars
Push the covers in firmly until they engage in position.
Secure the transit bars to the back of the washing machine. Make sure that the
top catch is located above the holder.
Risk of damage from incorrect
transport. The washing machine may become damaged if moved without the transit
bars in place. Keep the transit bars in a safe place. Fit them again if the
machine is to be moved (e.g. when moving house).
62
INSTALLATION
Fitting the transit bars
Opening the covers
Installation
Press against the retainer with a sharp object (a narrow screwdriver, for
example).
The cover opens.
Fitting the transit bars To fit the bars, follow the instructions
for removing them in reverse order. Tip: The bars will slide in more easily if
you lift the drum slightly.
63
INSTALLATION
Installation
Levelling the machine
The washing machine must stand perfectly level on all four feet to ensure safe
and proper operation. Incorrect installation may increase electricity and
water consumption and may cause the machine to move about.
Screwing out and adjusting the feet The four adjustable screw feet are used for levelling the washing machine. The machine is supplied with all four feet are screwed in.
Use a level to check that the washing machine is standing level.
Hold foot 1 securely with a pipe wrench. Turn counter nut 2 again using the
spanner supplied until it sits firmly up against the housing.
Using the spanner supplied, turn counter nut 2 in a clockwise direction. Then turn counter nut 2 together with foot 1 to unscrew.
Risk of damage due to incor-
rectly aligned washing machine. There is a danger of the washing machine
moving about if the feet are not secured. Turn all four counter nuts for the
feet until they sit firmly up against the housing. Please also check this for
the feet which did not need adjustment.
64
INSTALLATION
Installing under a continuous worktop
Risk of electric shock due to ex-
posed cables There is a risk of coming into contact with live parts while the
lid is removed. Do not remove the washing machine lid.
This washing machine (with lid intact) can be pushed under a countertop if
there is space to do so.
Installation
Washer-dryer stack The washing machine can be combined with a Miele tumble
dryer in a washerdryer stack. The appropriate “WTV” stacking kit to match
your dryer is required. All parts marked are available from your Dealer or
Miele. Please note:
a = at least 2 cm b = WTV without drawer: 172 cm
WTV with drawer: 181 cm c = 65 cm
65
INSTALLATION
Installation
The water protection system
The Miele water protection system protects all parts of the washing machine
from water damage. The system consists of three main components: – the inlet
hose – the electronic unit and drainage and
overflow protection – the drain hose Inlet hose – Protection against bursting
The inlet hose is tested to withstand pressure of at least 7,000 kPa.
Electronic unit and washing machine housing – Sump Any leaking water is
collected in a sump in the base of the machine. A float switches off the water
inlet valves, preventing any more water from flowing into the machine and
water in the suds container is pumped away. – Overflow protection This
prevents the washing machine taking in too much water. If the water level
exceeds a certain level, the drain pump switches in and pumps the excess water
away. Drain hose The drain hose is protected by a ventilation system which
prevents the washing machine from being emptied completely.
66
Connection to the water supply
Health risk and risk of damage
due to contaminated incoming water. The quality of the incoming water must
correspond to the drinking water specification of the country in which the
washing machine is being operated. Always connect the washing machine to the
mains water supply.
The washing machine should be connected to the mains water supply in
accordance with current local and national safety regulations. The German
authorities do not require it to have a non-return valve as the washing
machine has been designed to comply with DIN regulations. The water connection
pressure needs to be between 100 kPa and 1000 kPa. If the water connection
pressure exceeds 1000 kPa, a pressure reducing valve must be installed. A
stopcock with a ¾ inch threaded union is required for the connection. If this
is not available, only a qualified installer may connect the washing machine
to the mains water supply.
The connection point is subject to mains water pressure. Turn on the stopcock
slowly and check for leaks. Correct the position of the washer and the
threaded union if necessary.
The washing machine is not suitable for connection to a hot water supply. The
washing machine must not be connected to a hot water supply.
INSTALLATION
Maintenance Only use a genuine Miele hose that has been pressure tested to
withstand at least 7,000 kPa should you ever need a replacement.
Damage caused by dirty water.
A filter is located in the open end of the inlet hose and another in the
intake point to protect the inlet valve in the washing machine. These filters
must not be removed. Hose extension Longer hoses 2.5 or 4.0 m in length are
available from your Miele Dealer or Miele as optional extras.
Installation
67
INSTALLATION
Installation
Water drainage
The suds are drained through a drain pump with a 1 m delivery head. For the
water to drain freely, the hose must be free of kinks. If required, the hose
can be extended to a length of up to 5 m. Accessories are available from Miele
or from your Miele dealer. For a delivery head of more than 1 m (up to a max.
of 1.8 m) a replacement drain pump will need to be fitted. Please contact
Miele for advice. For a delivery head of 1.8 m the hose can be extended to a
length of up to 2.5 m. Accessories are available from Miele or from your Miele
dealer.
Drainage options: 1. Directed into a sink or basin:
Please note: Hook the hose over the edge and
secure it. If the water is pumped into a
washbasin, make sure that it can drain away freely. Otherwise there is a risk
of water overflowing or of some of the drained water being sucked back into
the machine. 2. Connected securely to a plastic drain pipe with a rubber
nipple (there is no need to use a siphon). 3. Connected securely to a floor
drain (gully). 4. Connected securely to a washbasin with plastic nipple.
Please note:
a Adapter b Spigot nut c Hose clip d End of the hose Fit adapter to the sink
drain outlet
using nut . Attach the end of hose to adapter
. Use a screwdriver to tighten hose clip
up close to the nut.
68
INSTALLATION
Installation
Electrical connection
The washing machine is supplied with an electrical connection cable with
moulded plug ready for connection to a switched socket.
The socket must be easily accessible after the washing machine has been
installed. If that is not possible, ensure that a suitable means of
disconnection is provided on the installation side for each pole.
Risk of fire from overheating.
Connecting the washing machine to a multi-socket plug adapter or to an
extension lead can overload the cable. Do not use an extension lead or multi-
socket plug adapter.
Temporary or permanent operation on an autonomous power supply system or a power supply system that is not synchronised with the mains power supply (e.g. island networks, back-up systems) is possible. A prerequisite for operation is that the power supply system complies with the specifications of EN 50160 or an equivalent standard. The function and operation of the protective measures provided in the domestic electrical installation and in this Miele product must also be maintained in isolated operation or in operation that is not synchronised with the mains power supply, or these measures must be replaced by equivalent measures in the installation. As described, for example, in the current version of BS OHSAS 180012 ISO 45001.
The electrical system must comply with local and national safety regulations (BS 7671 in the UK). We recommend the use of a suitable RCD . If the connection cable is damaged, it must only be replaced with a specific connection cable of the same type (available from the Miele Customer Service Department). For safety reasons, such replacement may only be carried out by a qualified technician or the Miele Customer Service Department. The data plate indicates the nominal power consumption and the appropriate fuse rating. Compare the specifications on the data plate with those of the electricity supply and make sure that they match. If in any doubt, consult a qualified electrician.
69
Consumption data
70
Programme
Load
Energy
Water
Running time
Temperature1
Residual moisture
Speed
kg
kWh
Litres
h:min
°C
%
rpm
ECO 40-60*
8.0
0,72
62
3:39
40
51
1400
4.0
0,47
50
2:39
37
51
1400
2.0
0,20
28
2:39
25
54
1400
Cottons
60
8,0
1,35
57
2:29
55
53
1400
20
8.0
0,40
72
2:39
20
53
1400
Minimum iron
30
3.5
0,45
52
1:59
30
30
1200
Express 202
40
3.5
0,34
30
0:20
29
60
1200
Woollens
30
2.0
0,23
35
0:38
1200
QuickPowerWash
40
4.0
0,58
40
0:49
1400
- Test programme for compliance with EU legislation regarding ecodesign 2019/2023 and energy labelling in accordance with Regulation No. 2019/2014
1 Maximum laundry temperature reached in main wash.
2 Short extra option activated
Information for customers Consumption data can vary from the nominal values given depending on water pressure, water hardness, water inlet temperature, room temperature, type and volume of load, fluctuations in the mains voltage and any extra options selected.
Height Width Depth Depth with door open Height for building under Width for building under Weight Capacity Supply voltage Rated load Fuse rating Consumption data Minimum water flow pressure Maximum water flow pressure Water inlet hose length Drain hose length Connection cable length Maximum delivery head Maximum drainage length LEDs Test certifications awarded Power rating in off mode
Technical data
850 mm 596 mm 643 mm 1077 mm 850 mm 600 mm Approx. 90 kg 8.0 kg dry laundry
See data plate See data plate See data plate See “Consumption data” 100 kPa (1
bar) 1000 kPa (10 bar) 1.60 m 1.50 m 2.00 m 1.00 m 5.00 m Class 1 See data
plate 0,40 W
71
Programmable functions
The programmable functions are used to alter the machine’s electronics to suit
changing requirements. Programmable functions can be altered at any time. The
programming is carried out in eight steps (, , … ) using the sensor controls.
Accessing the programming level Pre-requisites: – The washing machine is
switched on
(the programme selector is pointing to a wash programme). – The washing
machine door is open. Touch the Start/Add laundry sensor and leave your finger
on it whilst carrying out steps -. Close the washing machine door. Wait until
the Start/Add laundry sensor lights up constantly … … and then take your
finger off the Start/Add laundry sensor. After approx. four seconds, will
light up in the time display.
Choosing and selecting a programmable function
The number of the programmable function will appear in the time display as and
a number: e.g. .
Touch the or sensor control to scroll to the next or previous programmable
function:
Programmable functions Keypad tone PIN code Control field switch-off behaviour
Memory Additional long pre-wash Cottons Gentle action Reduced temperature
Water plus Water plus level Maximum rinse level Suds cooling Anti-crease Low
water pressure Display brightness dimmed
Confirm the selected programmable function by touching the Start/Add laundry
sensor control.
72
Programmable functions
Editing and saving a programmable function
You can either switch a programmable function on/off or select different
options. Touch the or sensor control to
switch the programmable function on/off or to select an option:
Programmable function
Available options
= Can be selected = Factory default setting
Confirm the chosen selection with the Start/Add laundry sensor control.
The number of the programmable function, e.g. , will then light up again.
Exit programming level
Turn the programme selector to . The option you have selected is now stored in
memory. You can change it again at any time.
Sensor tone
Each touch of a sensor control is confirmed with an audible tone.
Selection
= Sensor tone is switched off = Sensor tone is set to normal
volume (factory default setting) = Sensor tone is set to loud volume
73
Programmable functions
Lock code
The lock code prevents the washing machine being used without your knowledge.
When the code has been activated, you have to enter a code after switching the
washing machine on. Otherwise the washing machine cannot be operated. Options
= Lock code switched off (factory default setting)
= Lock code is switched on
Using the washing machine with a lock code The code is 125 and cannot be
altered. Switch on the washing machine. appears in the time display and the
and sensors light up. Touch the sensor. appears in the time display. Confirm
the number with the Start/
Add laundry sensor. The first number was saved and you can now enter the
second number using the and sensors. Also enter the second and third num-
bers and confirm the numbers with the Start/Add laundry sensor. The lock is
released and a wash programme can now be selected and started.
Control panel switch-off status
To save energy the time display and sensors will go out after 10 minutes, and
only the Start/Add laundry sensor will flash slowly. Options
= Off The time display and sensors will remain lit up while the washing
machine is switched on
= On (factory default setting) The time display and sensors will switch off
after 10 minutes if the programme is started. However; the time display and
sensors will remain lit up for 10 minutes after a delay start time has
elapsed, after the end of the programme or at the end of the anti-crease
phase.
74
Programmable functions
Memory
The washing machine will save the last settings (temperature, spin speed and
some of the extras) selected for a programme after the programme has started.
When this programme is chosen again, these saved settings will appear in the
display. Options
= Memory is switched off (factory default setting)
= Memory is switched on
Longer pre-wash Cottons
If you require a longer pre-wash you can extend the pre-wash time. Options
= No increase in the pre-wash time (factory default setting)
= + 6 minutes increase in the pre-wash time
= + 9 minutes increase in the pre-wash time
= + 12 minutes increase in the pre-wash time
Gentle action
Activating gentle action reduces the drum action and is suitable for washing
lightly soiled items more gently. Gentle action can be activated for the
Cottons and Minimum iron programmes. Options = Gentle action is switched off
(factory default setting) = Gentle action rhythm is
switched on
Reduce temperature
The boiling point for water is lower at high altitudes. In order to avoid
water boiling, Miele recommend activating the reduce temperature setting at
altitudes of more than 2000 m above sea level. The maximum temperature is
reduced to 80 °C even when a higher temperature is selected. Options = The
reduce temperature setting
is switched off (factory default setting) = The reduce temperature setting is
turned on
75
Programmable functions
Water plus
You can determine the amount of water used if the Water + extra is selected.
Selection
= More water is used in the wash and rinse stages (factory default setting)
= An extra rinse is carried out = The water level in the wash
and rinse stages is increased and an extra rinse is carried out
Water plus level
There are three different water levels which can be selected by activating the
Water + extra.
Options
= No higher water level (factory default setting)
= Water level increase by 1 level when washing and rinsing
= Water level increase by 2 levels when washing and rinsing
= Water level increase by 3 levels when washing and rinsing
Maximum rinse level
The water level in the rinse cycle can be permanently set to the highest
value. This function is useful for allergy sufferers as it achieves an
excellent rinse result. Water consumption will increase. Options
= Maximum rinse level is switched off (factory default setting)
= Maximum rinse level is switched on
76
Programmable functions
Suds cooling
When this is activated, additional water flows into the drum at the end of the
main wash to cool the suds down. Hot suds can damage plastic drainage pipes.
Suds cooling takes place when a temperature of 70 °C or higher is selected for
the Cottons programme. Suds cooling should be activated: – to prevent the
danger of scalding if
the drain hose is hooked over the edge of a sink or basin. – where drainage
pipes do not comply with DIN 1986. Options = Suds cooling is switched off
(factory default setting) = Suds cooling is switched on
Anti-crease
The anti-crease function helps prevent creasing if laundry is not going to be
removed immediately after the end of the programme. The drum continues to turn
at intervals for up to 30 minutes at the end of the programme. The door can be
opened at any time. Options = The anti-crease function is
switched off = The anti-crease function is
switched on (factory default setting)
Low water pressure
If the water pressure is below 100 kPa (1 bar), the washing machine cancels
the programme and the fault message appears. If the water pressure cannot be
increased, activating this function will prevent the programme from being
cancelled. Options = Low water pressure is
switched off (factory default setting) = Low water pressure is switched on
Backlight brightness dimmed
The brightness of the dimmed sensors in the control panel can be set to one of
seven different levels. The brightness changes as soon as you select a
different setting. Options = Darkest level
= Lightest level = (Factory default setting)
77
Detergents and care products
Detergent, fabric care, additives and machine care products are available for this washing machine. All the products have been designed for Miele washing machines. These and many other useful products can be ordered via the internet at www.miele.co.uk or from Miele (see end of this booklet for contact details).
WoolCare delicates detergent (liquid detergent) – For wool, silks and
delicates – Special care complex based on
wheat protein and with colour-protection formula – Best wash results at
20/30/40/60 °C
Detergent
UltraWhite (powder detergent) – Best results at 20/30/40/60/95 °C – Radiant
white laundry thanks to
powerful formula with active oxygen – Excellent stain removal even at low
temperatures
UltraColor (liquid detergent) – Best wash results at 20/30/40/60 °C – With
colour-protection formula for
brilliant colours – Excellent stain removal even at low
temperatures
78
Detergents and care products
Specialist detergents
These specialist detergents are available as convenient single-use capsules.
Caps Sport – For synthetic fabrics – Neutralises odours thanks to built-in
odour absorber – Prevents static charge in clothes – Retains the shape and
breathability
of synthetic fabrics
Caps DownCare – For down-filled items – Retains the elasticity and breathabil-
ity of down – Lanolin for effective cleaning and
gentle care – Down does not stick together and re-
tains its loft
Caps WoolCare – Woollens and delicates detergent – Special wheat-protein-based
agents – Fibre-protection technology to help
prevent items shrinking and felting – Colour-protection formula for gentle
cleaning
Caps UltraDark – Special-purpose detergent for dark
and black laundry – Colour-protection formula for gentle
cleaning – Anti-pilling effect protects your gar-
ments from discolouration
– Retains colour intensity and brightness
Caps CottonRepair – Special-purpose detergent for cotton
fabrics – Visibly renews fabric with just one
wash – Special Miele formula with No-
vozymes technology – Removes pilling and renews colour
intensity and brightness – Depending on fabric do not use more
than 12 times per year
Caps SilkCare – Silks and delicates detergent – Special care product made with
silk
protein – Preserves the smooth surface of silk
textiles – Gentle cleaning to protect silk fibres
79
Detergents and care products
Fabric care
These fabric care products are available as convenient single-use capsules.
Fabric conditioner cap – Fabric conditioner for freshly scented
laundry – Pure and thorough cleanliness with a
fresh scent – For soft, bouncy laundry – Prevents static charge in clothes
Cap ImpraProtect – Proofing agent for sportswear and
waterproof clothing – Effective proofing to protect against
water and wind, and to give a dirt-repellent finish – Retains the
breathability of fabrics
Additives
Additives are available as convenient single-use capsules.
Cap Booster – Highly effective stain remover – Enzyme technology to help
remove
stubborn stains – Suitable for whites and colours – For best wash results even
at low
temperatures
Machine care
Descaling agent – Removes heavy limescale deposits – Mild and gentle with
natural citric
acid – Gentle on heater elements, drum and
other components
IntenseClean – For hygienic cleanliness in washing
machines – Removes grease, bacteria and asso-
ciated unpleasant odours – Effective thorough cleaning
Water softener tablets – Reduces the amount of detergent
needed for hard water – Less detergent residue in fabrics – Less chemicals in
waste water due to
reduced amount of detergent
80
United Kingdom Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TW Tel: 0330 160 6600, Internet: www.miele.co.uk/service, E-mail: info@miele.co.uk
Australia Miele Australia Pty. Ltd. ACN 005 635 398 ABN 96 005 635 398 1
Gilbert Park Drive Knoxfield, VIC 3180 Tel: 1300 464 353 Internet:
www.miele.com.au
China Mainland Miele Electrical Appliances Co., Ltd. 1-3 Floor, No. 82 Shi Men
Yi Road Jing’ an District 200040 Shanghai, PRC Tel: +86 21 6157 3500 Fax: +86
21 6157 3511 E-mail: info@miele.cn, Internet: www.miele.cn
Hong Kong, China Miele (Hong Kong) Ltd. 41/F – 4101, Manhattan Place 23 Wang
Tai Road Kowloon Bay, Hong Kong Tel: (852) 2610 1025 Fax: (852) 3579 1404
Email: customerservices@miele.com.hk Website: www.miele.hk
India Miele India Pvt. Ltd. 1st Floor, Copia Corporate Suites, Commercial Plot
9, Mathura Road, Jasola, New Delhi – 110025 E-mail: customercare@miele.in
Website: www.miele.in
Ireland Miele Ireland Ltd. 2024 Bianconi Avenue Citywest Business Campus
Dublin 24 Tel: (01) 461 07 10 Fax: (01) 461 07 97 E-Mail: info@miele.ie
Internet: www.miele.ie
Malaysia Miele Sdn Bhd Suite 12-2, Level 12 Menara Sapura Kencana Petroleum
Solaris Dutamas No. 1 Jalan Dutamas 1 50480 Kuala Lumpur, Malaysia Phone:
+603-6209-0288 Fax: +603-6205-3768
New Zealand Miele New Zealand Limited IRD 98 463 631 8 College Hill Freemans
Bay, Auckland 1011 New Zealand Tel: 0800 464 353 Internet: www.miele.co.nz
Singapore Miele Pte. Ltd. 29 Media Circle #11-04 ALICE@Mediapolis Singapore
138565 sTel: +65 6735 1191 Fax: +65 6735 1161 E-Mail: info@miele.com.sg
Internet: www.miele.sg
South Africa Miele (Pty) Ltd. 63 Peter Place Bryanston 2194 P.O. Box 69434
Bryanston 2021 Tel: (011) 875 9000 Fax: (011) 875 9035 E-mail:
info@miele.co.za Internet: www.miele.co.za
Thailand Miele Appliances Ltd. BHIRAJ TOWER at EmQuartier 43rd Floor Unit
4301-4303 689 Sukhumvit Road North Klongton Sub-District Vadhana District
Bangkok 10110, Thailand
United Arab Emirates Miele Appliances Ltd. Showroom 1 Eiffel 1 Building Sheikh
Zayed Road, Umm Al Sheif P.O. Box 114782 – Dubai Tel. +971 4 3044 999 Fax.
+971 4 3418 852 800-MIELE (64353) E-Mail: info@miele.ae Website: www.miele.ae
Manufacturer: Miele & Cie. KG, Carl-Miele-Straße 29, 33332 Gütersloh, Germany
WWD 320 en-GB
M.-Nr. 11 660 200 / 01
References
- Welcome to Miele Australia - Immer Besser
- Home
- Service
- Welcome to Miele – Immer Besser.
- Welcome to Miele – Immer Besser.
- Welcome to Miele – Immer Besser.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>