LUTEC 7120315213 Post Lantern Owner’s Manual
- June 13, 2024
- LUTEC
Table of Contents
LUTEC 7120315213 Post Lantern
Product Information
Product Name: POST LANTERN
Model Number: 7120315213
Package Contents
| Part | Description | Quantity |
|---|---|---|
| A | Cap Cover | 3 |
| B | Fixture Top | 3 |
| C | Pole Middle | 3 |
| D | Pole Bottom | 1 |
| E | Base | 1 |
| F | Expansion Bolt | 1 |
| G | Hexagon Screw | 1 |
Hardware Contents
| Item | Quantity |
|---|---|
| Wire Nut | 6 |
| White Wire | 1 |
| Black Wire | 1 |
| Positioning Paper | 1 |
| Wrench | 1 |
Safety Information
Please read and understand this entire manual before attempting to assemble, operate, or install the product.
WARNING:
- Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or switching off circuit breaker).
- Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from electric shock.
CAUTION:
- All electrical connections must be in agreement with local codes, ordinances, or the National Electric Code (NEC). Contact your municipal building department to learn about your local codes, permits, and/or inspections.
- Do not connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use a fixture in a two-wire system that is not grounded. If you are not sure your lighting system has a grounding means, do not attempt to install this fixture. Contact a qualified, licensed electrician for information with regards to proper grounding methods as required by the local electrical code in your area.
- If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type and electrical rating required.
Preparation
Before beginning to assemble or install the lighting fixture, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble, install, or operate the product.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included):
- Flathead Screwdriver
- Phillips Screwdriver
- Pliers
- Electrical Tape
- Wire Cutters
- Safety Glasses
- Ladder
- Wire Stripper
- 1/2 in. Wrench
- 1/2 in. Ring Spanner
- Electric Drill
Product Usage Instructions
Assembly Instructions
-
1. Attach the three fixtures (C) to the top pole (D) by screwing the nuts.- Connect white wire from each fixture (C) to the white wire (FF) and the white sensor line by twisting a wire nut (EE) onto bare ends of the wires. Connect the black wire from each fixture (C) to the red sensor line by twisting a second wire nut (EE) onto the bare ends of the wires. Connect the black wire (GG) to the black sensor line by twisting a third wire nut (EE) onto the bare ends of the wires. Install the pole cover.
- Secure the bottom pole (F) to the base (G) with the hexagon screws (BB) by using the wrench (DD).
- Pass the wire through the middle pole (E), and then turn…
POST LANTERN
Owners Manual
MODEL #7120315213
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Cap | 3 |
| B | Cover | 3 |
| C | Fixture | 3 |
| D | Top Pole | 1 |
| E | Middle Pole | 1 |
| F | Bottom Pole | 1 |
| G | Base | 1 |
HARDWARE CONTENTS
(not shown actual size)
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
WARNING:
- Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or switching off circuit breaker).
- Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from electric shock.
CAUTION:
- All electrical connections must be in agreement with local codes, ordinances or the National Electric Code (NEC). Contact your municipal building department to learn about your local codes, permits and/or inspections.
- Risk of fire — most dwellings built before 1985 have supply wire rated for 140ºF. Consult a qualified electrician before installation.
- Do not connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use a fixture in a two-wire system that is not grounded. If you are not sure your lighting system has a grounding means, do not attempt to install this fixture. Contact a qualified, licensed electrician for information with regards to proper grounding methods as required by the local electrical code in your area.
- If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type and electrical rating required.
PREPARATION
Before beginning to assemble or install lighting fixture, make sure all parts
are present. Compare parts with package contents list and hardware contents
list. If any part is missing or damaged, do not attempt to assemble, install
or operate the product.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Flathead Screwdriver, Phillips
Screwdriver, Pliers, Electrical Tape, Wire Cutters, Safety Glasses, Ladder,
Wire Stripper, 1/2 in. Wrench, 1/2 in. Ring Spanner, Electric Drill.
ASSEMBLY INSTRUCTIONS
-
Attach the three fixtures (C) to the top pole (D) by screwing the nuts.
-
Connect white wire from each fixture (C) to the white wire (FF) and the white sensor line by twisting a wire nut (EE) onto bare ends of the wires. Connect the black wire from each fixture (C) to the red sensor line by twisting a second wire nut (EE) onto the bare ends of the wires. Connect the black wire (GG) to the black sensor line by twisting a thrid wire nut (EE) onto the bare ends of the wires. Install the pole cover.
Hardware Used
-
Secure the bottom pole (F) to the base (G) with the hexagon screws (BB) by using the wrench (DD).
Hardware Used
-
. Pass the wire through the middle pole (E), and then turn the top pole (D) clockwise into the middle pole (E).
-
Rotate the middle pole (E) clockwise onto the bottom pole (F).
-
Insert bulbs (not included). Use 60-watt max. medium-base E26 incandescent bulbs.
Note: CFLs and LEDs are recommended for this item. -
Install the cap (A) and the cover (B) onto the fixture (C).
-
Use the positioning paper (CC) to drill three holes on the ground.
Hardware Used -
Remove the preassembled nuts and washers from the expansion bolts (AA). Then put the expansion bolts (AA) into the drill holes.
Hardware Used -
Connect bare ground wire from the base (G) to the ground wire coming from the ground by twisting a wire nut (EE) onto bare ends of the wires. Connect white wire from the base (G) to the white wire coming from the ground by twisting a wire nut (EE) onto bare ends of the wires. Connect the black wire from the base (G) to the black wire coming from the ground by twisting a wire nut (EE) onto the bare ends of the wires. Secure the wire nuts (EE) with electrical tape.
Hardware Used -
With the help of another person, align the holes on base (G) with the expansion bolts and carefully place the pole assembly over the positioning paper. Secure assembly with washers and nuts removed in step 9.
CARE AND MAINTENANCE
To clean, unplug lamp and wipe with a damp, non-abrasive cloth.
OPERATING INSTRUCTIONS
The photocell in the fixture is designed to detect light and prevent the fixture from turning on when it senses daylight. At dusk, the light will turn on throughout the night until dawn. At dawn, the light will turn off throughout the day until dusk.
Note: If the fixture is installed in a shaded or covered area where there is little direct sunlight, the light may come on during the day.
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| The light will not go on. | 1. No power. |
2. Fixture may be wired incorrectly.
3. Switch may be wired
incorrectly.
| 1. Make sure lamp fixture is plugged in and power is on.
2. Check wiring.
3. Check wiring.
Fuse blows or circuit trips when fixture is turned on.| Crossed wires or power
wire is grounding out.| Consult a certified electrician.
The fixture shakes in high winds.| The screws and nuts may be secured
incorrectly.| Make sure the screws and nuts were secured tightly.
The light comes on during the day.
| 1. The fixture may be installed in a relatively dark location.
2. There is dust on the photocell.
| 1. Relocate the fixture.
**** 2. Periodically clean the surface of the photocell with a mild, non- abrasive cleaner.
The light flashes.| 1. Something is reflecting the light.| 1. Relocate the fixture away from reflective surfaces.
3-YEAR LIMITED WARRANTY
If this product fails due to a defect in materials or workmanship within three
(3) years from the date of purchase, return it along with proof of date of
purchase and it will be replaced with the same or comparable model free of
charge.
This warranty is void if damage or defect has resulted from accident, abuse,
misuse or faulty repair. This warranty gives you specific legal rights and you
may have other rights that vary from state to state.
IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL OR
INDIRECT DAMAGES OF ANY KIND ARISING OUT OF THE USE OR MISUSE OF THIS PRODUCT.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO
YOU.
LUTEC USA LLC:
149B Houston Rd Troutman NC 28166
Ningbo UTEC Electric Co.,LTD
CN8, Far East Industry Park, Yuyao, China
www.lutec.com
support@lutec.com
Please call our Customer Service line at
877-714-8669 for assistance Monday –
Friday 9 a.m. to 5 p.m. EST
Printed in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>