Honeywell 50608 Xerxes LED Ceiling Fan User Guide

Honeywell 50608 Xerxes LED Ceiling Fan

PACKAGE CONTENTS

HARDWARE CONTENTS

Note: Some extra hardware may be included. The quantity listed above is the number required for installation.

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

• Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical Code and ANSI/NFPA 70- 199. Hire an electrician or consult a do-it-yourself handbook if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum of 7 feet from the blades to the floor and at least 30 inches from the tip of the blades to any obstruction.
• The weight of the fan is 26.07 pounds.
• DANGER: When using an existing outlet box, make sure it is securely attached to the building structure and can support the full weight of the fan. Failure to this can result in serious injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan after installation is complete.
• WARNING: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges.
• WARNING: Using a full-range dimmer switch to control fan speed will cause a humming sound from the fan. To reduce the risk of fire or electric shock, do NOT use a full-range dimmer switch to control fan speed.
• WARNING: To reduce the risk of fire, electric shock or personal injury, mount the fan to an outlet box marked “ACCEPTABLE FOR FAN SUPPORT” and use the mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. Secure the outlet box directly to the building structure. The outlet box and its support must be able to support the moving weight of the fan (at least 35 lbs.).
• WARNING: To reduce the risk of fire, electric shock or personal injury, wire connectors provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your house wire is larger than 12-gauge and/or there is more than one house wire to connect to the two fan lead wires, consult an electrician for the proper size wire connectors to use.
• WARNING: To reduce the risk of fire, electric shock or personal injury, do not bend the blade arms when installing them, balancing the blades or cleaning the fan. Do not insert objects between the rotating fan blades.
• WARNING: To reduce the risk of personal injury, use only parts provided with this fan. The use of parts other than those provided with this fan will void the warranty.
• CAUTION: Be sure the outlet box is properly grounded or a ground (green or bare) wire is present.
• CAUTION: Carefully check all screws, bolts, and nuts on the fan assembly ensure they are secured.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Please note changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CARE AND MAINTENANCE

At least twice each year, lower the canopy to check the downrod assembly and tighten all screws on the fan. Clean the motor housing and blades with a soft brush or lint-free cloth to avoid scratching the finish.

Important: Shut off the main power supply before you begin any maintenance task. Do NOT use water or a damp cloth to clean the fan.

PREPARATION

Before beginning the assembly of this product, ensure all parts are present. Compare all parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated assembly time: 2 hours

Tools required (not included): Electrical tape, Phillips Screwdriver, Safety Glasses, Step Ladder, and Wire Strippers.

1. Turn off power to the fan at the breaker box and the wall switch (Figure 1.1). DANGER: Failure to disconnect the power supply prior to installation may result in serious injury or death.
2. Choose one of the following mounting options (Figure 1.2) :
   • Standard Mount – best suited for ceilings 8 feet or higher. For very high ceilings, use a longer downrod (not included). Angle Mount – best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary to ensure proper blade clearance. Ensure the ceiling angle is not steeper than 10 degrees.
   • Flushmount Installation – not available for this model.
   • Closemount Installation – best suited for ceilings 8 feet or lower.
3. Choose a suitable location – Ensure the blades will be at least 30 inches from any obstructions. Also check the downrod length to ensure the blades will be at least 7 feet above the floor (Figure 1.3).

INITIAL INSTALLATION

1. Loosen all four mounting bracket screws and completely remove the two screws from the round holes in the canopy. Then remove mounting bracket from the canopy and save them for later (Figure 2.1).
2. Install the mounting bracket to the outlet box (sold separately) using the screws and washers provided with the outlet box (Figure 2.2).
3. Remove the three fitter plate screws and the packing material from the motor assembly. Discard the orange packing material from the top and bottom of the motor assembly but save the three fitter plate screws for later (Figure 2.3).

For CLOSEMOUNT INSTRUCTIONS, skip to page 6.

STANDARD OR ANGLE MOUNT INSTRUCTIONS

1. Remove the downrod clip and downrod pin from the downrod. Then partially loosen the set screws in the yoke at the top of the motor assembly (Figure 3.1).
2. Feed the fan wires through the yoke cover, canopy and downrod (Figure 3.2).
3. Slide the downrod into the yoke of the motor assembly. Align holes and reinstall the downrod pin and downrod clip and secure with the two set screws (Figure 3.3).
4. Depending on the length of downrod you use, you may want to cut the fan wires to simplify wiring. After pulling the wires all the way through the downrod, measure 8 inches of wire. Cut off the excess wire using wire cutters (not included). Then strip 1/2 inch of insulation from the end of each wire strand (Figure 3.4).
5. Install the ball end of the downrod into the opening of the mounting bracket (Figure 3.5). WARNING: Failure to align the slot in the ball with the tap on the mounting bracket may cause the fan to fall, which could result in injury or death.
6. Insert the receiver into the opening of the mounting bracket with flat side facing up (Figure 3.6).

Skip to FINAL INSTALLATION, page 6.

CLOSEMOUNT INSTRUCTIONS (optional)

1. Remove the canopy cover from the bottom of the canopy (Figure 4.1).
2. Remove the three Phillips-head closemount screws from the top of the motor assembly. Then align the canopy with the holes in the top of the motor assembly. The larger holes in the canopy will encompass the remaining screws. Secure the canopy to the top of the motor assembly with the previously removed closemount screws (Figure 4.2).
3. Raise the motor assembly and place the canopy on the hook of the mounting bracket to free hands during the wiring process (Figure 4.3). Then, insert the receiver into the opening of the mounting bracket.

FINAL INSTALLATION

1. Use wire connnectors to connect household supply and fan wires according to the diagram (Figure 5.1) and the following steps:
   • Connect the green wire from the downrod and mounting bracket to the Bare/Green (ground) supply wire. Note: Closemount installation does not use the downrod, so there will only be two Green wires to connect.
   • Connect the White wire with red label from the receiver to the White (neutral) supply wire.
   • Connect the Red wire with red label from the receiver to the Black (hot/power) supply wire.
   • Connect the Black wire with white label from the receiver to the Black fan wire.
   • Connect the Blue wire with white label from the receiver to the Blue fan wire.
   • Connect the White wire with white label from the receiver to the White fan wire.
2. Align the canopy over the loosened mounting bracket screws. Place the J-slot of the canopy onto the mount bracket screws and rotate clockwise (Figure 5.2).
3. Secure the canopy with the two previously removed mounting bracket screws. Tighten all the mounting bracket screws securely (Figure 5.3).
4. Partially insert three blade screws through the blade arm and the blade. Secure each blade screw with a blade screw cap, starting with the one in the middle. Repeat this step for the remaining blades and blade arms (Figure 5.4).
5. Insert blade arm (K) through slots in the side of the motor assembly. Align the holes of one blade arm with two motor screw holes in underside of the motor assembly. Secure with two motor screws. Repeat this step for the remaining blade arms (Figure 5.5).
6. Remove one of the three fitter plate screws preassembled to the fitter plate and loosen the other two but do not remove. Connect the single-pin connector from the fitter plate to the single-pin connector from the light kit — Blue to Black and White to White. Align the slotted holes in the light kit with the loosened screws in the fitter plate. Turn light kit clockwise and replace the previously removed fitter plate screw. Tighten all screws (Figure 5.6).
7. Attach the lens cover to the light kit by twisting the lens cover tightly in a clockwise direction (Figure 5.7).
8. Remove the battery cover from the back of the remote transmitter and insert the 12-volt battery, noting polarity — positive (+) to positive (+) and negative (-) to negative (-). Replace the battery cover. If battery is installed correctly, the LED indicator on the front of the remote transmitter should illuminate when any button is pushed (Figure 5.8).
9. (Optional) If you wish to install the wall bracket for the remote, insert the two screws through the wall bracket and into the wall. Once the wall bracket is installed, hang the slot in the back of the remote over the top of the wall bracket (Figure 5.9). Turn on power to fan at breaker box and the wall switch. Assembly is complete.

OPERATING INSTRUCTIONS

1. To operate the fan using the remote, press and release the following buttons:
   • A – High fan speed
   • B – Medium fan speed
   • C – Low fan speed
   • D – Fan Power – Turns the fan off. Light Delay Off mode – Press and hold the fan power button for five seconds, which will turn off light after one minute. The LED indicator on the remote will flash four times to confirm mode setting.
   • E – Light Control: Dimmable Bulbs – Press light control to turn lights off and on. Press and hold light control to dim or  brighten the lights. Non-dimmable Bulbs -Turns the lights on and off. Note: The dimmer function does not work with CFL bulbs.
   • F – D/CFL Switch: Switch should be set to “D” to correspond with the included LED bulbs, which will enable the dimming function. Flip to “CFL” if you change to non-dimmable bulbs. (Figure 6.1).
2. Use the reverse switch located on the top of the motor assembly to optimize your fan for seasonal performance. In warmer weather, push the reverse switch left, which will result in downward airflow creating a wind chill effect. In cooler weather, push the reverse switch right and the fan to low, which will result in upward airflow that can help move stagnant, hot air off the ceiling area (Figure 6.2).

TROUBLESHOOTING

If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing difficulty in installation, please contact Customer Service: 1-877-361-3883.

Warning: Shut off the power supply before you begin any maintenance task.

LIMITED LIFETIME WARRANTY

Set forth below, the manufacturer, Hong Kong China Electric Appliance Company (HKC) warrants the fan motor for this ceiling fan to be free from defects in workmanship and material for the life of the product. Also, subject to the limitations below, HKC warrants all ceiling fan parts (“ceiling fan parts” excludes the motor and parts made in whole or in part with glass) to be free from defects in workmanship and material for a period of one year after the date of purchase by the original purchaser at retail.

All claims must be made by the original purchaser, whether such purchaser purchased the product through a store or contractor. Ceiling fan part defects must be reported within the first year from the date of purchase. Parts made in whole or in part with glass and the finishes of metal and other surfaces are not warranted.

Purchasers are responsible for all costs of removing and reinstalling the product. Any damage to any part caused by ordinary wear and tear, accident, misuse, or improper installation, is not covered by this warranty. HKC assumes no responsibility whatsoever for fan installation. Any service performed by a non-licensed electrician will render the warranty invalid.

HKC’s sole responsibility shall be to repair or replace the motor, parts, or product within the terms stated above. HKC shall not be liable for any loss or damage of any kind, including any incidental or consequential damages resulting directly or indirectly, from any breach of warranty, express or implied, or any other failure of this product. Some states do not allow the exclusion or limitation of incidental or consequential damages so this limitation may not apply to you.

If the original purchaser ceases to own the fan, this warranty is voided.

Should the purchaser encounter a problem with your fan related to defects in workmanship or materials within the warranty period associated with the defective part, HKC agrees to replace the defective part without charge, or at its option, to replace the ceiling fan with a comparable or superior model.

HKC’s warranties are limited to the written warranties set out in this HKC ceiling fan limited lifetime warranty. All other express and implied warranties, including, without limitation, the implied warranty of fitness for a particular purpose and the implied warranty of merchantability are disclaimed. Some states do not allow the disclaimer of implied warranties, so this disclaimer may not apply to you.

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department (1-877-361-3883). Monday-Thursday 8am – 6pm, Friday 8am – 5pm, Eastern Standard Time.

The Honeywell Trademark is used under license from Honeywell International Inc ™.

Honeywell International Inc. makes no representations or warranties with respect to this product.

This product is manufactured for Hong Kong China Electric Appliance, LTD.

• 3350 Players Club Parkway, Suite 225
• Memphis, TN 38125
• 1 877-361-3883
• 9326 • 051818

FAQs

What is the Honeywell 50608 Xerxes LED Ceiling Fan?

The Honeywell 50608 Xerxes LED Ceiling Fan is an 8-blade, 62-inch ceiling fan designed to enhance air circulation in large rooms over 400 sq. ft. It is suitable for modern or transitional homes.

How long does it take to install this fan?

Installation is estimated to take 45-60 minutes and a detailed guide is included to assist you with the process.

What are the mounting options for this fan?

The fan offers dual-mount hanging options. It comes with a standard 4-inch downrod for standard ceilings. Additionally, it can be angle-mounted for vaulted ceilings with a longer downrod (sold separately).

Is the downrod adjustable?

The fan comes with a 4-inch downrod and a 54-inch lead wire, allowing for longer downrods if needed.

What are the blades made of?

The blades have a dual finish, offering Matte Black on one side and Ash on the other, allowing you to choose the finish that best fits your space.

How many blades does this fan have?

The fan has 8 blades designed for maximum air circulation at high speeds.

Does the fan come with a remote control?

Yes, the fan comes with a remote control that allows you to adjust the fan speed and light. It even comes with a wall mount for easy access. Batteries are included.

Is the fan reversible?

Yes, the fan has a reversible motor that allows for optimized air circulation during both winter and summer months.

What kind of light does this fan have?

The fan has integrated lighting with frosted white glass, offering a fluid look. The LED board inside provides 1400 lumens and 18 watts.

Is there a warranty on this fan?

Yes, each Honeywell ceiling fan is backed by a limited lifetime warranty.

Is this fan suitable for larger rooms?

Yes, this 62-inch ceiling fan is ideal for larger rooms over 400 sq. ft., such as living areas, master bedrooms, dens, and more.

Is this fan energy-efficient?

It uses LED lighting, which is more energy-efficient than traditional lighting options.

Video- Product Overview and Installation

Download This PDF Link:  Honeywell 50608 Xerxes LED Ceiling Fan User Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>