Spido 002965 COMBO PREMIUM 5.5 Economic Filtration Unit User Manual

**Spido 002965 COMBO PREMIUM 5.5 Economic Filtration Unit User Manual

**

SECURITY

Electrical safety instructions

Read all the safety instructions and warnings below. Ignoring the safety instructions can lead to serious accidents.

SAFETY NOTICE

Please read the operating instructions carefully and familiarise yourself with the components and correct use of this product. The manufacturer is not liable for any damage caused by failure to follow the instructions. Damage caused by not following the instructions and guidelines is not covered by the warranty. Keep these instructions for use, they must be passed on to any user to whom the pump has been passed on.

• Persons who are not familiar with the contents of this manual must not use this appliance. This appliance may only be used by children over 8 years of age as well as by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they are supervised or have been instructed in the safe use of the appliance and understand the risks involved. Children must not play with the appliance.
  Cleaning and maintenance by the user must not be carried out by unsupervised children.

• The pump must not be used when people are in the water.

• The pump must be supplied by a fault current protection device (RCD / FI switch) with a measured fault current less than 30 mA.

• If the main connection cable of the appliance is damaged, it must be replaced by the manufacturer or his service department or another qualified person, to avoid risks.

• Switch off the power supply to the appliance and allow it to cool down before cleaning, maintenance and storage.

• Protect electrical components from moisture. Never immerse them in water or other liquids during cleaning or operation to avoid electric shock. Never place the appliance under running water.

• Electrical wiring must be carried out by a competent specialist and in accordance with local regulations.

• To avoid the risk of electric shock, never use extension cords.

Safety instructions of people and materials

• The risk of suction from the pump, if it cannot be avoided, can lead to serious or fatal accidents. Do not block the suction line at the pump or in the pool, as this could cause serious injury or  even death.
• The filter unit / pump must never be flooded or submerged.
• Never immerse the pump or filter in the pool.
• Never change the position of the valve when the filter unit is in operation.
• Install the filter unit at a sufficient safety distance from the pool to prevent children from using the installation as an entrance to the pool.
• Never connect the filter unit to the mains while you are in the water.
• Never work on the filter unit while it is connected to the mains.
• Never put the filter unit into operation while people are in the pool.
• Keep children away from electrical installations.
• Never allow children to handle the system.
  We do not accept any liability for damage caused by the Failure to observe the instructions contained in these operating instructions.

PACKAGING

Your filter unit has been carefully packed for transport. Make sure that on receipt the packaging is intact and that all parts are present. If you ordered the package by mail, make sure that the delivery is complete. Transport damage must be reported immediately to the carrier (transport company or postman). The carrier is responsible for the damage, the supplier is not responsible.

TECHNICAL DATA

| COMBO PREMIUM 5.5| COMBO PREMIUM 7.0| COMBO PREMIUM 9.5
---|---|---|---
Flow rate (m3/h – bar)| 5.5 – 0,4| 7 – 0,4| 9.5 – 0,4
Tank volume (L)| 25| 25| 40
Input / Output (mm)| 38 – 32 – 25
Rated voltage (VAC / Hz)| 230 / 50
Power (Watts)| 40| 55| 90
Degree of protection (I.P.)| X5
Filter size| 380 x 460| 380 x 460| 380 x 660
Quantity of Aqualoon (g)| 350| 350| 700

INSTALLATION

Unpacking the filter system Carefully remove all product components from the packaging before starting the installation.

Caution for use :
Do not use with products containing flocculant or PHMS / Active Oxygen, risk of clogging the filter media. If this happens, backwash and if necessary machine wash the Aqualoon in cold water.

INSTALLATION OF THE FILTER

To install the pump and filter, proceed as follows:

• Never cover the pump and filter to avoid overheating.
• The pump should not be placed above the water level as it is not self- priming and the risk of running dry or of air bubbles not being visible is very high. Damage resulting from dry running of the pump is not covered by the warranty.
• Place the pump and filter on a flat, stable base, in a place with sufficient ventilation and protection from sunlight, and easily accessible for maintenance work, following the suggestions below.
• The filter must be installed vertically at least 3.5 metres from the edge of the pool and ensure that it cannot fall into the water. Make sure that there is space around the filter for cleaning and maintenance.
• Do not operate the filter at pressures above 0.4 bar. Position the filter so that the inlet and outlet hose connections are already facing the pool to avoid unnecessary bending or folding of the connecting hoses.
• It is recommended to use pipes at the water inlet and outlet that are equal to each other and have a diameter equal to or greater than the diameter of the fittings provided

FIRST INSTALLATION

• Connect connection 3 to the suction of the pump 2 ;
• Connect connection 5 to output 4 of the pump;
• Insert and secure the tube 6 into the fitting 5 ;
• Insert fitting 7 into hose 6 and secure it;
• Connect connection 7 to inlet 9 of the filter;
• Connect connection 3 to output 8 of the filter.
• Connect the hose from the pool drain to connection 3 of the pump;
• Connect the filter return hose to the pool;
• If the pump does not rest properly on the ground, loosen the grey ring nuts on connections 5 and 7 to adjust the connection height. Then tighten the ring nuts.
• Check that the diverter valve is in the ‘FILTER’ position.
• Only after you have made all the above connections should you connect the pump cable to the power supply.

IMPORTANT: The electronic board integrated in the pump has been programmed to guarantee 3 levels of protection:

Protection against rotor lock-up :
A blockage or abnormal operation of the rotor may occur due to excessive fouling. In this case, the internal electronic board will make 20 attempts to start, followed by a short interval of time, then 20 more attempts to restart the pump properly. If the pump does not restart automatically after the 20+20 attempts, the circuit board will remain powered but the motor will stop. In this case, to restart the pump, it will be necessary to remove and reinsert the plug into the socket.

Protection against dry running and thermal overheating :
This protection comes into play if the pump runs without water or if the motor overheats. In both cases, the pump stops. The motor will also stop when the pump is no longer supplied with water. As above, to restart the pump it will be necessary to remove and reinsert the plug into the socket.

CAUTION: Do not underestimate the magnetic force of the rotor assembly. If you accidentally lose your grip and the shaft hits the pure ceramic rear bearing, the risk of damaging the bearing is very high. Such damage will result in the replacement of the damaged part.

CLEANING

CLEANING THE FILTER MEDIA WITH THE PATENTED SYSTEM

The COMBO PREMIUM filter unit is equipped with a patented system that makes it easy to clean the filter media without having to open the filter.

CLEANING OPERATIONS

• Stop the pump connected to the filter by removing the power supply.
• Raise handle 10 until it locks.
• Turn both selectors 11 ‘FILTER/ CLEAN’ bin line with the word CLEAN.
• Press the flow switch 20 with the palm of your hand and turn it clockwise until it stops. Now release it.
• Reactivate the pump by reconnecting it to the power supply.
• Press handle 10 until the filter media are crushed. Repeat the operation until the water coming out of the drain hose is clean. (Be careful if the water contains chlorine, drain in a suitable place, preserving the plants and grass). This cleaning system uses the water in the pool, so once the filter media have been cleaned, reset the pool to the desired level.

RESTORATION OF FILTERING OPERATIONS

• Now lift the handle 10 until it locks.
• Stop the pump connected to the filter by removing the power supply.
• With the handle 10 raised, turn the selector 11 «FILTER/CLEAN» in line with the «FILTER» marking.
• Lower the handle 10 until it locks.
• Press the flow switch 20 with the palm of your hand and turn it counter- clockwise until it stops. Now release it.
• Remove coupling 13 from the exhaust pipe and close it with cap 12.
• Reactivate the pump by reconnecting it to the power supply

FILTER MAINTENANCE – CLEANING AND REPLACING SPONGES AND FILTER MEDIA

CAUTION: Always disconnect the pump from the mains before carrying out any maintenance.

• Once the pump has been disconnected from the mains, it is advisable to remove the water inlet and outlet pipes in order to work without any obstruction.
• Never open the metal ring 16 before disconnecting the pump.
• Open the metal sealing ring 16.
• Remove the filter cover, paying attention to the seal. This should be washed and possibly greased (silicone grease only) for future use.
• Remove the sponges and fibre and wash them under running water or replace them.
• Remove the grid at the bottom of the filter and wash the area underneath thoroughly under running water.
• Reassemble the filter by following the steps described above in reverse order.
• Check that seal 17 of the cover is correctly positioned.

MAINTENANCE AND WINTERIZATION

For correct and efficient operation, the pump requires simple but necessary periodic maintenance. First, remove the plug from the socket and proceed as follows:

1. Release the locking ring on the scroll by pulling the tab outwards.
2. Remove the ring.
3. Remove the pump housing by rotating it and pulling it forward at the same time (in case of clogging, this may require a certain strength).
4. Remove the complete rotor with the flange.
5. Rinse under running water, using a toothbrush to remove any encrustations.
6. Reassemble in reverse order, ensuring the seal is in the correct position and insert the volute, wetting the seal to facilitate insertion.
7. Replace the ring with the larger teeth facing the pump and close it by pressing the tab until you hear a «click». Any damage to the seal, however minor, can seriously affect the performance of the pump and will require replacement.

EXTRAORDINARY MAINTENANCE AND REPLACEMENT OF THE ROTOR ASSEMBLY

For complete cleaning or replacement of the rotor assembly, proceed as follows: repeat the opening operations as indicated in points 1, 2, 3, 4 of the maintenance paragraph.

Insert the supplied hook inside the pump sleeve. Hook the bearing and pull it out. Clean the bearing under running water (do not use any detergents or cleaning products of any kind as they pollute the water: we recommend using a solution of water and vinegar using a soft brush to remove limescale deposits. If it is very worn, replace it with a new one. Put the bearing back into the pump sleeve after wetting it and push it in fully

WINTER PERIOD
The filter and pump must be protected against freezing. The appliance must be switched off during the winter season. Remove all water from the filter and pump, dismantle it and store it in a sheltered, dry place. Remove the rotor assembly from the pump, wash it thoroughly, and store the pump and rotor separately. Store the unit and accessories in a dry, temperature- controlled area, 0/40 degrees Celsius. It is recommended to keep the filter open during storage. You can reuse the original packaging to store the product and accessories.

WARNING!
Limescale deposits and natural wear of the components may cause an increase in the noise of the pump, but do not affect the proper functioning of the pump in any way. In this case, we recommend replacing the entire rotor.

FAULT RESOLUTION

suction line and the water level
Air is in the pump| A leak is present on the suction side of the pump| Retighten the hose connections and tighten the screws
Loosen the transparent cover of the filter cartridge (do not unscrew completely)to release the trapped air. Screw the cover back on tightly when all the air has escaped.
The filter is leaking| The seal is damaged| Check the sealand replace it if necessary
The pump does not work| The pump is not connected| Check the plug and the power cord
Residual current circuit breaker (RCD) has tripped| Reset the RCD residual current circuit breaker. If it trips again immediately, the pump or the controls are defective
The pump motor is defective| Replace the entire pump

For more technical information, missing parts or in case of a complaint, please contact your dealer.

GUARANTEE

• The manufacturer guaranteesThe filter unit is installed according to the installation instructions and operated according to the operating instructions.

• During repairs, the following should be used only original spare parts (wearing parts are not covered by the warranty).
  Wearing parts that are not covered by the warranty are as follows:

  • all O-rings for sealing
  • the seals of the sliding ring
  • the rotor and the turbine. operational safety and reliability only under the following conditions:

This product is guaranteed for 5 years from the date of purchase. This guarantee includes the free replacement of defective parts or of the appliance, the choice being left to the free initiative of the seller, subject to use in accordance with the instructions.

This guarantee also covers all the consequences of hidden defects or faults (article 1641 and following of the Civil Code).

Conditions of validity of the guarantee:
The appliance must always have been handled properly, following the instructions in this manual.
The appliance must not have been modified or repaired by anyone other than an authorised service centre.

The guarantee no longer applies in the following cases:

• non-compliance with the instructons (in particular no protection against frost, sand pumping, dry running, incorrect electrical connection, etc.),
• attempt to repair the device,
• technical changes to the device,
• se of non-original spare parts,
• damage/malicious acts (dropping or damaging the device),
• inappropriate use (e.g., lack of maintenance or cleaning

The following are some of the most common types of water treatment systems: industrial, (continuous operation), and in particular: passage of hard and heavy particles (pebbles), passage of an excessive quantity of sand, salty water, water with a high limestone content, etc,

Parts excluded from the warranty, beyond the first 6 months (in case these parts are supplied with the pump): suspension rope, coupling, discharge hose, crosshead and discharge pipe, valve, plugs, filter key, filter and tank bladder.

A warranty service or exchange with a new product during the warranty period does not extend the original warranty period

Appliances under warranty are handled by the product’s retailer.
The product must be accompanied by all its accessories and the original receipt or invoice as well as a letter explaining the reason for the return or the symptoms of failure found.

INFORMATION :

1. If your appliance stops working, first check whether there are other reasons, such as an interruption of the power supply or improper handling.
2. In the case of a repair, please ensure that the defective appliance is accompanied by the following documents :
   • invoice
   • description of the fault (as accurate a description as possible will speed up the repair).
3. Before sending in your device, remove all accessories that are not part of the original components supplied with the pump. We do not take responsibility for any missing accessories when the pump is delivered.

For a list of available parts, please contact your dealer.

ODREA will make every effort to supply the main spare parts for this product within and outside the warranty period.

The period provided for is 5 years from the date of manufacture of the product, which appears on the product’s nameplate.

In the event of a warranty claim or malfunction, please contact your dealer exclusively for a guarantee intervention or an exchange with a new product during the period.

The warranty period does not extend the original warranty period.
Only for EU countries.
Do not throw electrical/electronic devices in the trash!

According to the European Directive 2012/19/EU on old electrical and electronic equipment and its implementation in national legislation, used appliances of this type must be collected separately for recycling in accordance with environmental protection rules. If you have any questions, please contact your local waste disposal service.

Need the instructions in another language?
You can find it on the website www.spido.fr in the product sheet of the pump.

EU declaration of conformity
We, ODREA, declare in our sole responsibility that the product identified below comply with the basic requirements imposed by the EU directives specified below including all subsequent amendments.

References

• Pompes de jardin, d'évacuation ou de Piscine par Spido

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>