Profi-AirBrush AB02104 Kompressor Ultimate Instruction Manual

: June 13, 2024
: Profi-AirBrush

Table of Contents

Profi-AirBrush AB02104 Kompressor Ultimate
OPERATING INSTRUCTIONS
INTRODUCTION
IN GENERAL
MAINTENANCE
SECURITY TIPS
GUARANTEE REGULATIONS
TECHNICAL DATA
CONNECTION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Profi-AirBrush AB02104 Kompressor Ultimate

Profi-AirBrush-AB02104-Kompressor-Ultimate-PRODUCT-IMG

OPERATING INSTRUCTIONS

Profi-AirBrush-AB02104-Kompressor-Ultimate-FIG-1

Our wide range of products on the subject of airbrushes can be found on our website.

www.profi-airbrush.de

Technical changes, misprints and mistakes reserved! Newest information about our products can be found online: http://www.profi-pumpe.de.

SAFETY INSTRUCTION AND WARNINGS

Please read the user manual before using the pump
Warning sign
Warning of electrical voltage
Pull power plug
Protect from rain and moisture

INTRODUCTION

We would like to congratulate you on the purchase of our compressor. We appreciate your trust. That‘s why functional security and operational safety stands on first place for us.
To prevent damage to persons or property, you should read this user manual carefully. Please observe all safety precautions and instructions for proper use of the airbrush components. Failure to follow the instructions and safety precautions can result in injury or property damage.
Please keep this manual with the instructions and safety instructions carefully in order to at any time you can restore them.

IN GENERAL

The compressors are developed according to the newest stand of technology, manufactured with much care and go under strict intensive controls.
Make sure after unpacking that the data given on the type label match with the included operating instructions. In the case of doubt is not to be used. Transport damages are immediately to be reported to the package distributor on the shipping invoice and to us in written form.

RANGES OF APPLICATION

Airbrush compressors can be used in:
Bodypainting
Fingernail painting
Cosmetic
Craftwork spraying
And much more. lt can be also used for providing air source for medical, environment protect, breed aquatics Indnstrial, food Industrial, chemical industrial, laboratory and so on.

OPERATION DIRECTORY / TROUBLESHOOTING
The Original air hose have rubber airproof inside; the user can make the airtight by hand, and get good performance. If the air hose is not original, usually the air hose and air compressor cannot be well airproof. However, 100% airtight is only effective for auto stop function air compressor. Teflon tape can be used to prevent leakage.

Connect the equipment for your application to the outgoing 1/8“ male fitting at the front of the cylinder head,To keep the connecting fitting from leaking air you should always apply teflon tape to the thread of the fitting.
Connect the compressor to a protected power supply line with the same voltage as specified on the product label.
Adjust the outlet air pressure on the Filter/Regulator (see fig).
Compressor running is controlled automatically by a pressure switch,referring to the pressure in the outlet. Do not use the compressor continuously for longer than 10 minutes. Allow the compressor to cool down for 15 minute after every 10 munites working cycle. Motor is equipped with a thermal protector with automatic reset.

Checking the air leakage. Please do not use the air to pressure reach the max pressure (auto stop function), for the compressors do not have auto stop function, please turn off the switch. Then check the needle of pressure gauge, if the needle on gauge is very steady, it is means the airtight is verv good. If the needle decline down quickly, it means there is air leakage in some place of connection. Please check and make it airtight. Or any small leakage will affect the performance of the compressor. (lt may lead to frequently auto stop and auto start) A compressors maximum pressure is the highest pressure it can build up. When a connected airbrush is opened, it is precisely with this pressure that compresssed air in itially shoots out through the airbrush nozzle. In contrast, the working pressure is the constant pressure the compressor can maintain during airbrushing. The level of this working pressure depends, on the other hand. the nozzle diameter of the airbrush to which it is connected; the larger the nozzle diameter, the greater the amount of air wich can escape and the lower the compressor‘s working pressure.

Tanks provide a reservoir of pressurized air that you can draw from while you’re spraying
You can draw air at a regulated pressure from the tank instead of the average pressure of the piston cylinder
The life of the compressor engine increases because it pumps air as the tank needs it instead of always being on.
Tanks are great first line moisture traps

MAINTENANCE

Cleaning the compressor after every use.
After every use,drain the water collected in the Filter/Regulator bowl (insofar as a pre-filter is present), pressing upwards the valve placed on the bottom side of the cup (outlet must be pressurized).
Every three months, clean the filter of the Filter/Regulator by blowing with compressed air.

The following controls should be carried out regularly

That the cable is not damaged
That the hoses are not bent or broken
Checking the air leakage
Open drain cock to exhaust condensate after every 40 working hours.
Caution!: Before each work on the compressor the security tips are to be followed.

SECURITY TIPS

Keep away from children! It is not a toy!

The compressor should not be taken by persons commissioning, which are under the influence of alcohol, drugs or medication.
Please, check before every use that the electrical connections as well as the cable are intact.
Moreover, it is not recommended to carry out technical modifications. First it is not sure whether these changes are technically flawless and secondly no guarantee can be therefore granted.
Obey absolutely valid regulations on the electrical security
The users shoild choose the right air compressor with suitable air flow and pressure according to the actual work requirement.
Pay attention to the Ambient temperatures between +5 and +40 ° C
Never leave the appliance exposed to dust, acids, vapors, explosive or flammable gasses or atmospheric agents (rain, sun, fog, snow)
The compressor may be used only in well ventilated area and will not be used in areas with steam or moisture, or near water.
Never use the appliance in your bare feet or with wet hands or feet.
Never pull on the electrical cable or hose
Restricted section in the tubing or cables
The device is to be secured / protected through a RCD circuit breaker (release current 30 mA).
The electrical connections are always to be carried out by an authorised professional
The compressor should not be used if it is damaged.

The manufacturer explains

To take over no responsibility in the case of accidents or damages on the basis of carelessness or disregard to the instructions in this book.
To reject every responsibility for the damages which originate from the improper use of the device.

Important note: please pay attention before commissioning the airbrush compressor!

Please, note that in dependence of the device used (compressor/gun) the color must be diluted.
Your airbrush gun must be cleaned thoroughly after each color change, otherwise the residual color mixes with the newly filled color.
Moreover, the very fine nozzle will be clogged by dried ink. The gun should be cleaned with thinner and water.
Especially the nozzles, which are subject to wear, will have longer lifetime by careful cleaning .
Please, inform yourself in the literature or on the Internet about the working methods and techniques before starting work .
Please, check the funktion of the gun with clean water. Is the function correctly given, the technology of the gun is perfect.
Please connect compressor, hose and gun always tight. Avoid oscillatingly opening (constant on and off) of the compressor in order to reduce wear and to save energy.
We sell only tested products. These are strictly for personal use.
Claims for damages for improper disassembly and cleaning can not be accepted.
Complaints about contaminated airbrush guns with paint,residues, could not be recognized .

GUARANTEE REGULATIONS

For all manufacturer defects and material defects we grant the legal guarantee time (new and unused product). In such cases we take over the exchange or the repair of the device. Forwarding expenses are not carried by us.
The guarantee is not valid with:
Material wear (sealing rings, impeller wheels, impeller chambers)
Unjustified interventions or changes in the device
Damages by selffault
Improper servicing and improper use
Moreover, we give no damage compensation for secondary damages!

NOTES ON DISPOSAL

Electrodevices of our company, labeled with the symbol of the crossed trash bin, are not permitted to be disposed in your household garbage.
We are registered at the German registration department EAR under the WEEE-No. DE79535656.
This symbol means, that you’re not allowed to treat this product as a regular household waste item – it has to be disposed at a recycling collection point of electrical devices.
This is the best way to save and protect our earth.
THANKS FOR YOUR SUPPORT!

EU DECLARATION OF CONFORMITY
The undersigned, Amur S.à r.l., 36, Rue de la Gare, L-5540 Remich, certifies that the products named overleaf, namely Ultimate-1, Universal II, Universal II-C, DUO-Power II, DUO-Power II-C, Compact II, Compact Mobil, DUO-Power Efficient as placed on the market, comply with the relevant provisions listed below, the relevant EU harmonised directives and the EU standard for safety. This declaration of conformity applies insofar as no modifications are made to the product. The sole responsibility for issuing this declaration of conformity lies with the manufacturer. The sole authorised person to keep the technical documents: Amur S.à r.l. – 36, Rue de la Gare – L-5540 Remich.

Machinery Directive (2014/30/EC)

The following harmonized standards:
EN-55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 61000-3-2:2019
EN 61000-3-3:2013+A1:2019

RoHS Directive 2011/65/EC

Signed for and on behalf of:
Amur S.à r.l.
Remich, 01.06.2023

TECHNICAL DATA

English

| Ultimate-1

(AB02104)

| Universal II

(AB02103-1)

| Universal II-C

(AB02103-2C)

| DUO-Power II

(AB02129)

| DUO-Power II-C

(AB02129-2C)

| Compact II/Mobil (AB04101S-1/ AB02102-2B)| Decor Design-II (AB02106)| DUO-Power Efficient (AB042027S)
---|---|---|---|---|---|---|---|---
Power| 150 Watt| 150 Watt| 125 Watt| 190 Watt| 190 Watt| 125 Watt| 190 Watt| 250 Watt
Max. air displacement| 20 – 25 l/m| 20 – 25 l/m| 20 – 25 l/m| 35 – 40 l/m| 30 – 35 l/m| 20 – 25 l/m| 65-68 l/m| 30 – 35 l/m
Max. pressure| 6 bar| 6 bar| 6 bar| 6 bar| 6 bar| 6 bar| 3.5 bar| 6,5 bar
Engine speed (rpm)| 1450| 1450| 1450| 1450| 1450| 1450| 1850| 1450
Voltage| 230V, 50Hz| 230V, 50Hz| 230V, 50Hz| 230V, 50Hz| 230V, 50Hz| 230V, 50Hz| 230V, 50Hz| 230V, 50Hz
Air tank| –| 3 L| 3 L| 3,5 L| 3,5 L| –| –| 3 L
Connection| 1/8“| 1/8“| 1/8“| 1/8“| 1/8“| 1/8“| 1/8“| 1/8“
Noise level| 47db| 47db| 47db| 49db| 47db| 47db| TBA| 47db
Dimension (cm)| 26x14x21| 35×13,5×31| 63x34x35| 35x13x31| 33×17,5×38,5| 26x14x17| 25×12,5×17| 34x30x28
Weight (kg)| 5| 5| 5| 7,2| 7| 3,6| 4,5| 16