Porter-Cable 100 Router Instruction Manual

Porter-Cable 100 Router Instruction Manual

IMPORTANT
Please make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations.

The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain them for future reference.
Model No. __
Type ____
Serial No.

IMPORTANT SAFETY INSTRUCTIONS

Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance, or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed. Porter-Cable strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed.

If you have any questions relative to its application DO NOT use the product until you have written Porter-Cable and we have advised you. Online contact form at www.porter-cable.com
Postal Mail: Technical Service Manager
Porter-Cable Corporation
4825 Highway 45 North
Jackson, TN 38305

Information regarding the safe and proper operation of this tool is available from the following sources: Power Tool Institute
1300 Sumner Avenue, Cleveland, OH 44115-2851 www.powertoolinstitute.org
National Safety Council1121 Spring Lake Drive, Itasca, IL 60143-3201

American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY
10036 www.ansi.org ANSI 01.1Safety Requirements for Woodworking
Machines, and the U.S. Department of Labor regulations www.osha.gov
SAVE THESE INSTRUCTIONS!

SAFETY GUIDELINES – DEFINITIONS

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury. used without the safety alert symbol indicates a potentially hazardous situation that, if not avoided, may result in property damage.

CALIFORNIA PROPOSITION 65
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contain chemicals known (to the State of California) to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints
• crystalline silica from bricks cement and other masonry products
• Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, always wear a NIOSH/OSHA- approved, properly fitting face mask or respirator when using such tools.

GENERAL SAFETY RULES

Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS
Work area safety

• Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool.
• Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.
• Unmodified plugs and matching outlets will reduce the risk of electric shock.
• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep the cord away from heat, oil, sharp edges, or moving parts.
• Damaged or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.

Personal safety

• Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use safety equipment. Always wear eye protection. Safety equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
• Avoid accidental starting. Ensure the switch is in the off-position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of these devices can reduce dust-related hazards.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories tool bits, etc., in accordance with these instructions and in the manner intended for the a particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Service
Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

ADDITIONAL SPECIFIC SAFETY RULES

1. HOLD THE POWER TOOL BY INSULATED GRIPPING SURFACES WHEN PERFORMING AN OPERATION WHERE THE CUTTING TOOL MAY CONTACT HIDDEN WIRING OR ITS OWN CORD. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.
2. USE CLAMPS OR OTHER PRACTICAL WAYS TO SECURE AND SUPPORT THE WORKPIECE TO A STABLE PLATFORM. Holding the work by hand or against your body is unstable and may lead to loss of control.
3. DISCONNECT TOOL FROM POWER SOURCE before making adjustments or changing bits.
4. TIGHTEN COLLET NUT securely to prevent the bit from slipping.
5. USE A CLAMP or some other device to hold the workpiece rigidly in position. and clear the path of the tool of obstructions.
6. PROVIDE CLEARANCE under the workpiece for the router bit when throughcutting.
7. CHECK TO SEE THAT THE CORD will not “hang up” during the routing operation.
8. CLEAR THE ROUTER BIT AREA before starting the motor.
9. MAINTAIN FIRM GRIP on router to resist starting torque.
10. KEEP HANDS CLEAR OF BIT when a motor is running to prevent personal injury.
11. KEEP CUTTING PRESSURE CONSTANT. Do not overload the motor.
12. LET THE MOTOR COME TO A COMPLETE STOP before putting the tool down.
13.  NEVER TOUCH router bits after use. They may be extremely hot.
14.  NEVER TIGHTEN COLLET NUT without a bit.
15. DO NOT USE ROUTER BITS with a diameter in excess of 2-1/2″ at RPM above 13,000. Router bits up to 3-1/2″ in diameter can be used when speed control is set for 13,000 RPM or less.
16. ALWAYS KEEP CHIP SHIELD clean and in place.
17. AVOID “CLIMB-CUTTING” (see “Using The Router” section in this manual). “Climb-cutting” increases the chance of loss of control resulting in possible personal injury.
18. DO NOT HAND-HOLD THE ROUTER IN AN UPSIDE-DOWN OR HORIZONTAL POSITION. The motor can separate from the base if not properly attached according to the instructions.
19. USE OF THIS TOOL CAN GENERATE AND DISBURSE DUST OR OTHER AIRBORNE PARTICLES, INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST AND ASBESTOS DUST. Direct particles
    away from the face and body. Always operate the tool in well-ventilated area and provide for proper dust removal. Use a dust collection system wherever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged contact with dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly fitting NIOSH/OSHA-approved respiratory protection appropriate for dust exposure, and wash exposed areas with soap and water.

SYMBOL DEFINITION

V …………………… volts
A …………………… amperes
Hz …………………… hertz
W …………………… watts
kW …………………… kilowatts
F …………………… farads
μF …………………… microfarads
l …………………… litres
g …………………… grams
kg …………………… kilograms
bar …………………… bars
Pa …………………… pascals
h …………………… hours
min …………………… minutes
s …………………… seconds
n0 …………………… no-load speed
min or …min-1 ……… Revolutions or reciprocations per minute

MOTOR
Many Porter-Cable tools will operate on either D.C. or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. current only. Refer to the specification plate on your tool for proper voltage and current rating. Do not operate your tool on a current on which the voltage is not within the correct limits. Do not operate tools rated A.C. only on D.C. current. To do so may seriously damage the tool.

EXTENSION CORD SELECTION
If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 volts) at 150% of rated amperes. If an extension cord is to be used outdoors, it must be marked with the suffix WA or W following the cord type designation. For example – SJTW-A indicates it is acceptable for outdoor use.

Length of Cord in Feet

115V| 25 Ft.| 50 Ft.| 100 Ft.| 150 Ft.| 200 Ft.| 250 Ft.| 300 Ft.| 400 Ft.| 500 Ft.
230V| 50 Ft.| 100 Ft.| 200 Ft.| 300 Ft.| 400 Ft.| 500 Ft.| 600 Ft.| 800 Ft.| 1000 Ft.
Nameplate Ampere Rating| 0-2| 18| 18| 18| 16| 16| 14| 14| 12| 12
2-3| 18| 18| 16| 14| 14| 12| 12| 10| 10
3-4| 18| 18| 16| 14| 12| 12| 10| 10| 8
4-5| 18| 18| 14| 12| 12| 10| 10| 8| 8
5-6| 18| 16| 14| 12| 10| 10| 8| 8| 6
6-8| 18| 16| 12| 10| 10| 8| 6| 6| 6
8-10| 18| 14| 12| 10| 8| 8| 6| 6| 4
10-12| 16| 14| 10| 8| 8| 6| 6| 4| 4
12-14| 16| 12| 10| 8| 6| 6| 6| 4| 2
14-16| 16| 12| 10| 8| 6| 6| 4| 4| 2
16-18| 14| 12| 8| 8| 6| 4| 4| 2| 2
18-20| 14| 12| 8| 6| 6| 4| 4| 2| 2

RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS
CARTON CONTENTS

• Router
• Wrenches (2)

FUNCTIONAL DESCRIPTION

FOREWORD
The router is one of the most useful tools in the woodworking field. It may be used for many cutting and shaping operations such as slotting, mortising, dadoing, grooving, rabbeting, corner-rounding, beading, dovetailing, veining, inlay work, etc

OPERATION

NOTE: This tool is shipped completely assembled. No assembly time or tools are required.

SELECTING THE BIT
This Router comes with a 1/4″ split-type collet which accommodates bits with 1/4″ shanks

Disconnect the tool from the power source while preparing it for use, making adjustments, and when it is not in use.

INSTALLING AND REMOVING THE BIT

DISCONNECT THE TOOL FROM THE POWER SOURCE

1. To remove the motor unit from the base unit: Open the clamp (A) Fig. 1.
2. While holding the base, turn the power unit COUNTERCLOCKWISE until the lower pin (B) in the motor housing is disengaged from the groove in the base. Lift the power unit free from the base unit.
3. Clean and insert the shank of bit into the collet until the shank bottoms, then back it out approximately 1/16″. Do not use router bits with a diameter in excess of 1.5″ in this tool.
4. Lay the power unit on its side on the bench with the collet pointing AWAY from you.
5. Place one wrench on the flats of the chuck with the opposite end of the wrench resting on the bench to your left (Fig. 2).
6. Place the other wrench on the collet and tighten COUNTERCLOCKWISE. TIGHTEN FIRMLY.
7. To remove the bit, reverse the procedure.

AVOID POSSIBLE DAMAGE TO COLLET. NEVER TIGHTEN COLLET WITHOUT BIT.
ATTACHING THE MOTOR TO THE ROUTER BASE
DISCONNECT THE TOOL FROM THE POWER SOURCE.

1. Open the clamp (A) Fig. 1 and set the power unit in the base unit.
2.  Align the lower pin of the power unit (B) Fig. 1 with the groove in the base.
3. Rotate the power unit CLOCKWISE into the base until the upper guide pins are set in the groove of the base.
4. Close the clamp.

ADJUSTING THE DEPTH OF THE CUT DISCONNECTS THE TOOL FROM THE POWER SOURCE.

1. Open the clamp (A) Fig. 3A.
2. Hold the base (E) and turn the power unit (F) Fig. 3A COUNTER-CLOCKWISE until the tip of the bit is above the bottom of the base.
3. Set the tool on a flat surface.
4. Turn the power unit (F) Fig. 3A CLOCKWISE until bit touches the work.
5. Close the clamp (A) Fig. 3A.
6. Rotate the depth adjusting ring (B) Fig. 3A until the zero-line (C) Fig. 3B is opposite the index line (D) Fig. 3B on the housing.
7. Open the clamp (A) Fig. 3A.
8. Tip the router so that the bit is clear of the wood surface. Turn the power unit (F) Fig. 3A CLOCKWISE until the index line (D) Fig. 3B on the motor housing reaches the desired depth indicated on the ring.
9. Close the clamp (A) Fig. 3A.

NOTE: Setting the index line to 1/4″ on the ring means the cutting edge of the bit is exposed 1/4″ below the base.

CONNECTING TO POWER SOURCE
Before connecting the tool to the power source ALWAYS MAKE SURE SWITCH IS IN THE “OFF” POSITION. Also, check that the power circuit is the same as that shown on specification plate of the router.

STARTING AND STOPPING THE MOTOR
Before starting the router, make sure that the bit is clear of the workpiece and foreign objects. Keep a firm grip on the router to resist starting torque Start and stop the motor by setting the toggle switch (A) Fig. 4 to the “ON” or “OFF” position. To avoid personal injury or damage to finished work, always allow the motor to come to a COMPLETE STOP before setting it down

USING THE ROUTER

IMPORTANT: Before using your router, consider the kind and total amount of material to be removed. Depending on the workpiece, more than one cut may be necessary to avoid overloading the motor. Before beginning the cut on the actual workpiece, make a sample cut on a piece of scrap lumber to show exactly how the cut will look, as well as enable you to check the dimensions. Always be sure that the work is rigidly clamped or otherwise secured before making a cut. Generally speaking, when working on a bench, the workpiece should be held on the bench by wood clamps. When routing edges, the router should be held firmly down and against the work by both guiding knobs. Since the cutter rotates clockwise (when viewing the router from the top), the router should be moved from left to right as you stand facing the work (see Fig. 5). When working on the inside of a temple, moving the the router in a clockwise direction. When working on the outside of a temple, move the router in a counterclockwise direction.

Avoid “Climb-Cutting” (cutting in a direction opposite that shown in Fig. 5). “Climb-cutting” increases the chance for loss of control resulting in possible personal injury. When “Climb-cutting” is required (backing around a corner), exercise extreme caution to maintain control of the router. The speed and depth of cut will depend largely on the type of workpiece. Keep the cutting pressure constant, but do not crowd the router so the motor speed slows excessively. More than one pass may be necessary on exceptionally hard woods or problem materials to get the desired depth of cut. When making cuts on all four edges of the workpiece, make the first cut on the end of the piece across the grain. Thus, if the chipping of wood occurs at the end of a cut, it will be removed when making the next cut parallel with the grain.

THE EDGE GUIDE
An optional Edge Guide is available to aid straight edge planing, parallel grooving, and dado or slotting operations. To assemble, insert guide rods (A) in holes in base Fig. 6 and secure them with screws (B). Adjust the guide (C) on the rods and secure it with thumb screws (D).

TEMPLET GUIDES
A wide variety of templet guides is available for use in pattern and templet routing operations. Fig. 7 shows a typical combination bit, templet guide, and locknut.

DISCONNECT THE TOOL FROM THE POWER SOURCE
To install, insert the templet guide in the center hole of the router base and secure it in place with the locknut.
BEFORE CONNECTING THE TOOL TO THE POWER SOURCE, install the bit, adjust the depth of cut, and rotate the router chuck by hand. Make sure that the bit or collet does not contact the templet guide.

TROUBLESHOOTING

For assistance with your tool, visit our website at www.porter- cable.com for a list of service centers or call the Porter-Cable helpline at 1-800-487-8665.

MAINTENANCE

KEEP TOOL CLEAN
Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air.

FAILURE TO START
Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact with the outlet. Also, check for blown fuses or open circuit breakers in the line.

LUBRICATION
This tool has been lubricated with a sufficient amount of high-grade lubricant for the life of the unit under normal operating conditions. No further lubrication is necessary.

BRUSH INSPECTION (If applicable)
For your continued safety and electrical protection, brush inspection and replacement on this tool should ONLY be performed by an AUTHORIZED PORTER- CABLE SERVICE STATION or a PORTER-CABLE DELTA FACTORY SERVICE CENTER. At approximately 100 hours of use, take or send your tool to your nearest authorized Porter-Cable Service Station to be thoroughly cleaned and inspected. Have worn parts replaced and lubricated with fresh lubricant. Have new brushes installed, and test the tool for performance. Any loss of power before the above maintenance check may indicate the need for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL UNDER THIS CONDITION. If proper operating voltage is present, return your tool to the service station for immediate service.

SERVICE

REPLACEMENT PARTS
When servicing use only identical replacement parts. For a service parts list or To learn more about Porter-Cable visit our website at www.porter- cable.com

SERVICE AND REPAIRS
All quality tools will eventually require servicing, or replacement of parts due to wear from normal use. For assistance with your tool, visit our website at  www.porter-cable.com for a list of service centers or call the Customer Care Department at 1-800-487-8665. All repairs made by our service centers are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by others. Should you have any questions about your tool, feel free to write us at any time. In any communications, please give all information shown on the nameplate of your tool (model number, type, serial number, etc.).

ACCESSORIES

complete line of accessories is available from your Porter-Cable Delta Supplier, Porter-Cable Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter- cable.com for a catalog or for the name of your nearest supplier. Since accessories other than those offered by Porter-Cable Delta has not been tested with this product, the use of Such accessories could be hazardous. For the safest operation, only Porter-CableDelta recommended accessories should be used with this product

WARRANTY

PORTER-CABLE LIMITED ONE YEAR WARRANTY
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of the original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period. For repair or replacement return the complete tool or accessory, transportation prepaid, to your nearest Porter- Cable Service Center or Authorized Service Station. Proof of purchase may be required. This warranty does not apply to repair or replacement required due to misuse, abuse, normal wear and tear, or repairs attempted or made by other than our Service Centers or Authorized Service Stations.

ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE OF PURCHASE. To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION, 4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights that vary from state to state.

PORTER-CABLE DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE  DELTA) (CENTRE DE SERVICE PORTER-CABLE DELTA) Parts and Repair Service for Porter-Cable Delta Power Tools are Available at These Locations
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable Delta) (Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien) CALIFORNIA Ontario 91761 (Los Angeles) 3949A East Guasti Road
Phone: 909-390-5555
Fax: 909-390-5554

Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service Center, or Porter-Cable  Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to the nearest Porter-Cable Delta Factory Service Center.

CANADIAN PORTER-CABLE  DELTA SERVICE CENTERS ALBERTA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: 403-735-6166
Fax: 403-735-6144

The following are trademarks of PORTER-CABLE DELTA (Las siguientes son marcas registradas de PORTER-CABLE DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®, Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®&(design), PORTERCABLE ®PROFESSIONAL POWER TOOLS, PORTER- CABLEREDEFINING PERFORMANCE™, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design)

The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ- BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®, WOODWORKER’S CHOICE™. Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.

Download PDF:Porter-Cable 100 Router Instruction Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>