Electrolux HHOF875S Combo Hob User Manual

Electrolux HHOF875S Combo Hob

Product Information

• Product Name: HHOF875S
• Product Type: Hob
• Manufacturer: Electrolux
• Website: www.electrolux.com

We’re Thinking of You

Thank you for purchasing an Electrolux appliance. You’ve chosen a product that brings with it decades of professional experience and innovation. Ingenious and stylish, it has been designed with you in mind. So whenever you use it, you can be safe in the knowledge that you’ll get great results every time. Welcome to Electrolux.

Visit our website to:

• Get usage advice, brochures, trouble shooter, service and repair information: www.electrolux.com/support
• Register your product for better service: www.registerelectrolux.com
• Buy Accessories, Consumables and Original spare parts for your appliance: www.electrolux.com/shop

Customer Care and Service

Always use original spare parts. When contacting our Authorised Service Centre, ensure that you have the following data available: Model, PNC, Serial Number. The information can be found on the rating plate.

Safety Information

Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not liable for any damages or injuries caused by improper installation or use of the appliance.

Safety Instructions

Installation

Only a qualified person must install this appliance. There is a risk of injury or damage to the appliance if installed incorrectly or by an unqualified person.
Ensure proper clearance is maintained between the hob and other appliances and units.

Electrical Connection

There is a risk of fire and electric shock if the electrical connection is not done properly. Only a qualified electrician should perform the electrical connection.

Use

There is a risk of injury, burns, and electric shock if the appliance is not used correctly. Follow the usage instructions provided in the user manual.
Do not use the hob for any purpose other than cooking. Do not leave flammable materials near the hob.
Do not let hot cookware fall on the appliance as it can cause damage to the surface.

Care and Cleaning
Follow the care and cleaning instructions provided in the user manual to ensure proper maintenance of the hob.

Service
If you require service or repairs for your appliance, contact our Authorised Service Centre with the Model, PNC, and Serial Number of your appliance.

Disposal
When disposing of the appliance, ensure proper safety measures are taken to avoid any risk of injury or suffocation.

Installation
Before the installation, write down the information from the rating plate located on the bottom of the hob, including the serial number.

Built-in Hobs
Only use the built-in hobs after assembling them into correct built-in units and work surfaces that align with the standards.

Connection Cable
Ensure the correct connection cable is used for installation.

Attaching the Seal – Integrated Installation

1. Clean the rabbets in the worktop.
2. Cut the supplied 3x10mm seal stripe.
3. After assembling the hob, seal the remaining gap between the glass ceramic and the worktop with silicone. Make sure the silicone does not get under the glass ceramic.

Attaching the Seal – On-top Installation

1. Clean the worktop around the cut-out area.
2. Attach the supplied 2x6mm seal stripe to the lower edge of the hob, along the outer edge of the glass ceramic. Do not stretch it. Make sure that the ends of the seal stripe are located in the middle of one side of the hob.
3. Add some millimeters to the length when cutting the seal stripe.
4. Join the two ends of the seal stripe together.

Assembly

Refer to the installation booklet for detailed information on how to assemble your hob. Follow the hob connection diagram and the window switch connection diagram presented in the installation booklet and/or the labels under the hob.

HHOF875S
EN Hob

User Manual

2 www.electrolux.com

WE’RE THINKING OF YOU

Thank you for purchasing an Electrolux appliance. You’ve chosen a product that brings with it decades of professional experience and innovation. Ingenious and stylish, it has been designed with you in mind. So whenever you use it, you can be safe in the knowledge that you’ll get great results every time. Welcome to Electrolux. Visit our website to:
Get usage advice, brochures, trouble shooter, service and repair information: www.electrolux.com/support
Register your product for better service: www.registerelectrolux.com
Buy Accessories, Consumables and Original spare parts for your appliance: www.electrolux.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts. When contacting our Authorised Service Centre, ensure that you have the following data available: Model, PNC, Serial Number. The information can be found on the rating plate.
Warning / Caution-Safety information General information and tips Environmental information
Subject to change without notice.
1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not

ENGLISH 3
responsible for any injuries or damage that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.1 Children and vulnerable people safety · This appliance can be used by children aged from 8
years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children of less than 8 years of age and persons with very extensive and complex disabilities shall be kept away from the appliance unless continuously supervised. · Children should be supervised to ensure that they do not play with the appliance and mobile devices with the dedicated app. · Keep all packaging away from children and dispose of it appropriately. · WARNING: Keep children and pets away from the appliance when it operates or when it cools down. Accessible parts become hot during use. · If the appliance has a child safety device, it should be activated. · Children shall not carry out cleaning and user maintenance of the appliance without supervision. 1.2 General Safety · This appliance is for cooking purposes only. · This appliance is designed for single household domestic use in an indoor environment. · This appliance may be used in, offices, hotel guest rooms, bed & breakfast guest rooms, farm guest houses and other similar accommodation where such use does not exceed (average) domestic usage levels.

4 www.electrolux.com
· WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements.
· WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire.
· Never use water to extinguish the cooking fire. Switch off the appliance and cover flames with e.g. a fire blanket or lid.
· WARNING: The appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by a utility.
· CAUTION: The cooking process has to be supervised. A short term cooking process has to be supervised continuously.
· WARNING: Danger of fire: Do not store items on the cooking surfaces.
· Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.
· Do not use the appliance before installing it in the built-in structure.
· Do not use a steam cleaner to clean the appliance. · After use, switch off the hob element by its control and
do not rely on the pan detector. · If the glass ceramic surface / glass surface is cracked,
switch off the appliance and unplug it from the mains. In case the appliance is connected to the mains directly using junction box, remove the fuse to disconnect the appliance from power supply. In either case contact the Authorised Service Centre. · Ensure good air ventilation in the room where the appliance is installed to avoid the backflow of gases into the room from appliances burning gas or other fuels, including open fires. · Make sure that the ventilation openings are not blocked and the air collected by the appliance is not conveyed into a duct used to exhaust smoke and

ENGLISH 5

steam from other appliances (central heating systems, thermosiphons, water- heaters, etc.). · When the appliance operates with other appliances the maximum vacuum generated in the room should not exceed 0.04 mbar. · Clean the hood filter regularly and remove grease deposits from the appliance to prevent the risk of fire. · If the supply cord is damaged, it must be replaced by the manufacturer, an authorized Service or similarly qualified persons in order to avoid a hazard. · If the appliance is connected directly to the power supply, the electrical installation must be equipped with an isolating device that allows to disconnect the appliance from the mains at all poles. Complete disconnection must comply with conditions specified in the overvoltage category III. The means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules. · WARNING: Use only hob guards designed by the manufacturer of the cooking appliance or indicated by the manufacturer of the appliance in the instructions for use as suitable or hob guards incorporated in the appliance. The use of inappropriate guards can cause accidents.

2. SAFETY INSTRUCTIONS
2.1 Installation
WARNING! Only a qualified person must install this appliance.
WARNING! Risk of injury or damage to the appliance.
· Remove all the packaging. · Do not install or use a damaged
appliance. · Follow the installation instructions
supplied with the appliance. · Keep the minimum distance from
other appliances and units.

· Always take care when moving the appliance as it is heavy. Always use safety gloves and enclosed footwear.
· Seal the cut surfaces with a sealant to prevent moisture from causing swelling.
· Protect the bottom of the appliance from steam and moisture.
· Do not install the appliance next to a door or under a window. This prevents hot cookware from falling from the appliance when the door or the window is opened.
· Do not install the exhaust air into a wall cavity, unless the cavity is designed for that purpose.

6 www.electrolux.com

· For ductless installation, the fan outlet must be positioned directly against the wall or must be separated by an additional cabinet wall, in order to prevent access to the fan blades.
· Each appliance has cooling fans on the bottom.
· If the appliance is installed above a drawer: ­ Do not store any small pieces or sheets of paper that could be pulled in, as they can damage the cooling fans or impair the cooling system. ­ Keep a distance of minimum 2 cm between the bottom of the appliance and parts stored in the drawer.
· Remove any separator panels installed in the cabinet below the appliance.
2.2 Electrical Connection
WARNING! Risk of fire and electric shock.
· All electrical connections should be made by a qualified electrician according to the connection diagram or installation booklet.
· In case of exhaust installation, and where the accessories are present or mandatory (wall valve, window switch and/or window opener) electrical connections should be made by a qualified electrician, according to the connection diagram or installation booklet.
· The appliance must be earthed. · Before carrying out any operation
make sure that the appliance is disconnected from the power supply. · Make sure that the parameters on the rating plate are compatible with the electrical ratings of the mains power supply. · Make sure the appliance is installed correctly. Loose and incorrect electricity mains cable or plug (if applicable) can make the terminal become too hot. · Use the correct electricity mains cable.

· Do not let the electricity mains cable tangle.
· Make sure that a shock protection is installed.
· Use the strain relief clamp on the cable.
· Make sure the mains cable or plug (if applicable) does not touch the hot appliance or hot cookware, when you connect the appliance to a socket.
· Do not use multi-plug adapters and extension cables.
· Make sure not to cause damage to the mains plug (if applicable) or to the mains cable. Contact our Authorised Service Centre or an electrician to change a damaged mains cable.
· The shock protection of live and insulated parts must be fastened in such a way that it cannot be removed without tools.
· Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation.
· If the mains socket is loose, do not connect the mains plug.
· Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.
· Use only correct isolation devices: line protecting cut-outs, fuses (screw type fuses removed from the holder), earth leakage trips and contactors.
· The electrical installation must have an isolation device which lets you disconnect the appliance from the mains at all poles. The isolation device must have a contact opening width of minimum 3 mm.
2.3 Use
WARNING! Risk of injury, burns and electric shock.
· Do not change the specification of this appliance.
· Remove all the packaging, labelling and protective film (if applicable) before first use.
· Make sure that the ventilation openings are not blocked. The

ventilation must be checked periodically by a qualified person. · Do not let the appliance stay unattended during operation. · Set the cooking zone to “off” after each use. · Do not put cutlery or saucepan lids on the cooking zones. They can become hot. · Do not operate the appliance with wet hands or when it has contact with water. · Do not use the appliance as a work surface or as a storage surface. · If the surface of the appliance is cracked, disconnect immediately the appliance from the power supply. This to prevent an electrical shock. · Users with a pacemaker must keep a distance of minimum 30 cm from the induction cooking zones when the appliance is in operation. · When you place food into hot oil, it may splash. · Never use an open flame when the integrated hood operates.
WARNING! Risk of fire and explosion
· Fats and oil when heated can release flammable vapours. Keep flames or heated objects away from fats and oils when you cook with them.
· The vapours that very hot oil releases can cause spontaneous combustion.
· Used oil, that can contain food remnants, can cause fire at a lower temperature than oil used for the first time.
· Do not put flammable products or items that are wet with flammable products in, near or on the appliance.
WARNING! Risk of damage to the appliance.
· Do not keep hot cookware on the control panel.
· Do not put a hot pan cover on the glass surface of the hob.
· Do not let cookware boil dry. · Be careful not to let objects or
cookware fall on the appliance. The surface can be damaged.

ENGLISH 7
· Do not activate the cooking zones with empty cookware or without cookware.
· Do not put aluminium foil on the appliance.
· Never remove the grid or the hood filter when the integrated hood or the appliance operates.
· Never use the integrated hood without the hood filter.
· Do not cover the inlet of the integrated hood with cookware.
· Do not open the bottom lid when the integrated hood or the appliance operates.
· Do not place small or light objects near the integrated hood to avoid the risk of being trapped.
· Cookware made of cast iron, aluminium or with a damaged bottom can cause scratches on the glass / glass ceramic. Always lift these objects up when you have to move them on the cooking surface.
2.4 Care and cleaning
· Clean the appliance regularly to prevent the deterioration of the surface material.
· Switch off the appliance and let it cool down before cleaning.
· Do not use water spray and steam to clean the appliance.
· Clean the appliance with a moist soft cloth. Use only neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects.
2.5 Service
· To repair the appliance contact the Authorised Service Centre. Use original spare parts only.
· Concerning the lamp(s) inside this product and spare part lamps sold separately: These lamps are intended to withstand extreme physical conditions in household appliances, such as temperature, vibration, humidity, or are intended to signal information about the operational status of the appliance. They are not intended to be used in other applications and are not suitable for household room illumination.

8 www.electrolux.com
2.6 Disposal
WARNING! Risk of injury or suffocation.
· Contact your municipal authority for information on how to dispose of the appliance.
3. INSTALLATION
WARNING! Refer to Safety chapters.
3.1 Before the installation
Before you install the hob, write down the information below from the rating plate. The rating plate is on the bottom of the hob.
Serial number ………………………
3.2 Built-in hobs
Only use the built-in hobs after you assemble the hob into correct built-in units and work surfaces that align to the standards.
3.3 Connection cable
· The hob is supplied with a connection cable.
· To replace the damaged mains cable, use the cable type: H05V2V2-F which withstands a temperature of 90 °C or higher. Contact an Authorised Service Centre. The connection cable may only be replaced by a qualified electrician.
3.4 Attaching the seal Integrated installation
1. Clean the rabbets in the worktop. 2. Cut the supplied 3x10mm seal stripe
into 4 stripes. The stripes must have the same length as the rabbets. 3. Cut the ends of the stripes at an angle of 45°. They should fit in the corners of the rabbets accurately. 4. Attach the stripes to the rabbets. Do not stretch the stripes. Do not bond the ends of the stripes one over the other.

· Disconnect the appliance from the mains supply.
· Cut off the mains electrical cable close to the appliance and dispose of it.
After you assemble the hob, seal the remaining gap between the glass ceramic and the worktop with silicone. Make sure the silicone does not get under the glass ceramic.
3.5 Attaching the seal – On-top installation
1. Clean the worktop around the cut out area.
2. Attach the supplied 2x6mm seal stripe to the lower edge of the hob, along the outer edge of the glass ceramic. Do not stretch it. Make sure that the ends of the seal stripe are located in the middle of one side of the hob.
3. Add some millimetres to the length when you cut the seal stripe.
4. Join the two ends of the seal stripe together.
3.6 Assembly
Refer to the installation booklet for detailed information on how to assemble your hob.
Follow the hob connection diagram and the window switch connection diagram presented in the installation booklet and / or the labels under the hob.

ENGLISH 9

min. 500mm

min. 50mm

If the appliance is installed above a drawer, the hob ventilation can warm up the items stored in the drawer during the cooking process.
ON-TOP INSTALLATION

INTEGRATED INSTALLATION

830

515

830

515

80 250

830

515

98

55

212

500

254

442

7

9 22

16

770

480

min.55

780+1
max.R5 490 +1

min.55

490 min.4
220
min. 1500

830

515

103

60

217

500

254

442

7

9 22

16

770

480

min.55 min.55

780+1
max.R5 490 +1
R10

14,5 490

7

490+1 R5 780+1

28

519+1

834+1

min.4

220

min. 1500

25-50

25-50

10 www.electrolux.com
Find the video tutorial “How to install your Electrolux Extractor Hob” by typing
4. PRODUCT DESCRIPTION
4.1 Product overview

out the full name indicated in the graphic below.
www.youtube.com/electrolux www.youtube.com/aeg
How to install your Electrolux Extractor Hob
Filter housing assembly Before first use make sure to place the filter inside the housing, with the silver side facing out. Once the filter housing is assembled, put it inside the hood cavity and place the grid on the hood.

1

2

3

4

8 76 5

4

5 6

7 8

1 Grid 2 Filter 3 Filter housing 4 Hob 5 Tube

6 Cabinet back wall fitting 7 Tube 8 Adapter

4.2 Cooking surface layout
4
3 3
1

ENGLISH 11
1 Induction cooking zone 2 Control panel 3 Flexible induction cooking area
consisting of four sections 4 Hood

2

4.3 Control panel layout

67

8

9 10 11 12 13 14

5 4

32

1

16

15

Use the sensor fields to operate the appliance. The displays, indicators and sounds tell which functions operate.

Sen- sor field

Function

1

ON / OFF

2

Timer

3

/-

Description
To activate and deactivate the appliance. To set the function. To increase or decrease the time.

45

Timer display PowerSlide

To show the time in minutes. To activate and deactivate the function.

12 www.electrolux.com

Sen- sor field

Function

6

FlexiBridge (Flexible Bridge)

7

Pause

8910

Hood timer display Hood control bar Boost

11

AUTO Automatic mode of the hood

12

Breeze

13

Hood filter indicator

14 15 16 –

Lock / Child Safety De- vice PowerBoost
Hob control bar

Description
To switch between three modes of the function. To activate and deactivate the function. To show the time in minutes. To set a fan speed. To activate and deactivate the function. To activate and deactivate the function.
To activate and deactivate the function. To indicate and remind that the hood fil- ters should be cleaned. To lock / unlock the control panel.
To activate the function. To set a heat setting.

4.4 Display indicators

Indicator + digit / /

Description There is a malfunction.
OptiHeat Control (3 step Residual heat indicator): continue cook- ing / keep warm / residual heat. Wi-Fi is in the process of connecting.
Bluetooth is in the process of connecting.

5. BEFORE FIRST USE
WARNING! Refer to Safety chapters.
5.1 Wireless / app connection
In order to use the app the hob needs to be onboarded. Onboarding can be done with Wi-Fi or Bluetooth (recommended). 1. Download My Electrolux Kitchen from
the app store.

2. Open the app and register to get an account.
3. Add a new appliance.
4. Press and hold until and start to blink.
5. Follow the instructions in the app to complete the onboarding process.
When onboarding is completed and
stop blinking.

ENGLISH 13

Changing the network
In order to change the network you have to forget the current network and start the onboarding process again. 1. Go to Menu > User settings >
Onboarding and change the setting from On to Off.
6. DAILY USE
WARNING! Refer to Safety chapters.
6.1 Activating and deactivating
Press and hold to activate or deactivate the hob.
6.2 Pot detection
This feature indicates the presence of cookware on the hob and deactivates the cooking zones if no cookware is detected during a cooking session. If you put cookware on a cooking zone before you select a heat setting, the indicator above 0 on the control bar appears. If you remove cookware from an activated cooking zone and set it aside temporarily, the indicators above the corresponding control bar will start blinking. If you do not place the cookware back on the activated cooking zone within 60 seconds, the cooking zone will automatically deactivate. To resume cooking, make sure to put the cookware back on the cooking zones within the indicated timeout.
6.3 Heat setting
1. Press the desired heat setting on the control bar.

Refer to “Menu structure”.
The network is forgotten. 2. Open the app and start the
onboarding process again.
Refer to “Wireless / App connection”.
The indicators above the control bar appear up to the selected heat setting level. 2. To deactivate a cooking zone, press
0.
6.4 PowerBoost
This function makes more power available to the induction cooking zones. The function can be activated for the induction cooking zone only for a limited period of time. After this time the induction cooking zone automatically sets back to the highest heat setting.
Refer to “Technical data” chapter.
To activate the function for a cooking zone: touch . To deactivate the function: change the heat setting.
6.5 OptiHeat Control (3 step Residual heat indicator)
WARNING! / / As long as the
indicator is on, there is a risk of burns from residual heat.
The induction cooking zones produce the heat necessary for the cooking process directly in the bottom of the cookware. The glass ceramic is heated by the heat of the cookware.
The indicators / / appear when a cooking zone is hot. They show the level of the residual heat for the cooking zones you are currently using.
The indicator may also appear:

14 www.electrolux.com

· for the neighbouring cooking zones even if you are not using them,
· when hot cookware is placed on cold cooking zone,
· when the hob is deactivated but the cooking zone is still hot.
The indicator disappears when the cooking zone has cooled down.
6.6 Timer
Count Down Timer
Use this function to specify how long a cooking zone should operate during a single cooking session. You can set the function for the hood separately. Refer to “Hood functions”.
1. Press . 00 appears on the timer display.
2. Press or to set the time (00-99 minutes).
3. Press to start the timer or wait 3 seconds. The timer begins to count down.
To change the time: select the cooking zone with and press or .
To deactivate the function: select the cooking zone with and press . The remaining time counts back to 00.
The timer finishes counting down, a signal sounds and 00 blinks. The cooking zone deactivates. Press any symbol to stop the signal and blinking.

6.7 Power management
If multiple zones are active and the consumed power exceeds the limitation of the power supply, this function divides the available power between all cooking zones. The hob controls heat settings to protect the fuses of the house installation.
· Cooking zones are grouped according to the location and number of the phases in the hob. Each phase has a maximum electricity loading. If the hob reaches the limit of maximum available power within one phase, the power of the cooking zones will be automatically reduced.
· The heat setting of the cooking zone selected first is always prioritised. The remaining power will be divided between the other cooking zones according to the order of selection.
· For cooking zones that have a reduced power, the control bar blinks and shows the maximum possible heat settings.
· Wait until the display stops flashing or reduce the heat setting of the cooking zone selected last. The cooking zones will continue operating with the reduced heat setting. Change the heat settings of the cooking zones manually, if necessary.
· The hood extractor is always available as an electrical load.
Refer to the illustration for possible combinations in which power can be distributed among the cooking zones.

Minute Minder

1. Press . 2. Press or to set the time. The timer finishes counting down, a signal sounds and 00 blinks. Press any symbol to stop the signal and blinking.
To deactivate the function: press and . The remaining time counts back to 00.

6.8 Hood functions
WARNING! Refer to Safety chapters.

ENGLISH 15

Activating and deactivating the hood
The hood can operate alongside the hob during the cooking session, as well as while the hob is switched off.
1. Press one of the fan speed levels (1-3) on the hood control bar to activate the hood.
A signal sounds and indicators above the hood control bar appear. 2. Adjust the fan speed setting as
needed by pressing either of the available levels on the hood control bar. 3. To deactivate the hood, press 0 on the hood control bar. The indicators above the hood control bar disappear.
AUTO
The function automatically adjusts the fan speed level based on the selected heat setting level of the hob.
When you use the hob for the first time, the function is usually activated by default.
You can activate the function while the hob is on but none of the cooking zones are active, or at any point during the cooking session.
If you activate the function while the hob is off, none of the cooking zones operate and there is no residual heat visible on the control panel, the function will switch off by itself after a few seconds.

1. Press and hold to activate the hob.
2. Press AUTO to activate the function. A signal sounds and an indicator above the symbol appears. 3. Place cookware on the hob and
select a heat setting level. Increase or decrease the heat setting level as needed. The hood will react to the heat setting level, increasing or decreasing the fan speed level accordingly. The indicators above the hood control bar appear. 4. Press 0 on the hob control bar to
deactivate a cooking zone or to deactivate the hob. If the residual heat indicator appears, AUTO will continue to adjust the fan speed. If the remaining heat is low, Breeze might start operating as well. 5. To deactivate the function during cooking and switch to the manual mode of the hood, press AUTO or any other setting on the hood control bar. A signal sounds and the indicator above the symbol disappears.

Automatic modes – fan speed levels

Hood Residual heat level (hob is Residual heat level

mode off)

(hob is on)

0

Boiling Frying

H1 –

–

–

–

–

H2 –

–

–

–

–

–

–

1

–

1

1

1

H3 –

–

–

1

1

1

2

16 www.electrolux.com

Hood Residual heat level (hob is mode off)
0

H4 –

1

Residual heat level (hob is on)

1

1

2

Boiling Frying

2

3

If you deactivate the hob while AUTO is running, the function will be remembered for the next cooking session.
Hood timer
Use the function to specify how long the hood should operate.
It is not possible to set the hood timer while the hood is deactivated.
1. Press next to the hood control bar.
2. Press or to set the time (00-99 minutes).
3. Press to start the timer. The timer begins to count down. · Once the timer finishes counting
down, the hood stops operating. · It is possible to set the hood timer
while AUTO is on. If AUTO deactivates the hood before the set time runs out, the timer will be reset. · If the timer deactivates the hood before AUTO, the function will be switched off. The indicators above 0 and AUTO will disappear. · In both cases AUTO will be activated next time you switch on the hob.
Boost
The function activates the hood fan at its maximum speed level.
Press to activate the function. A signal sounds and an indicator above the symbol appears. The function can operate uninterrupted for a maximum of 10 minutes. After that time the fan speed setting automatically changes to 3. You can activate the function again, if needed.

Breeze
The function sets the hood fan to an extra low speed. The fan starts running at a minimum noise level immediately after the function is activated. You can use the function after cooking to remove any lingering smells or steam.
To activate the function when the hob is off:

1. Press . A signal sounds and an indicator above the symbol appears. A timer set to 60 minutes appears on the display next to the hood control bar.
2. Adjust the timer using or , if needed.
After the timer finishes counting down, the hood deactivates automatically.

6.9 Menu structure

The table shows the basic menu structure.
User settings

Sym- Setting bol

Possible op- tions

C1 Wi-Fi

On / Off (–)

C2 Wi-Fi signal Three levels of

strength

signal strength.

C3 Onboarding On – the hob is onboarded. Off (–) – the network is for- gotten.

b

Sound

On / Off (–)

h

Hood mode 1 – 4

ENGLISH 17

Sym- bol E

Setting
Alarm / error history

Possible op- tions
The list of re- cent alarms / errors.

To enter user settings: press and hold
. Then, press and hold . The settings appear on the timer of the left cooking zones.
Navigating the menu: the menu consists of the setting symbol and a value. The symbol appears on the rear timer and the value appears on the front timer. To navigate between the settings
press on the front timer. To change
the setting value press or on the front timer.

7. ADDITIONAL FUNCTIONS

7.1 Automatic Switch Off
The function deactivates the hob automatically if:
· all of the cooking zones, as well as the hood, are deactivated,
· you do not set any heat setting or fan speed setting after the activation of the hob,
· you spill something or put something on the control panel for more than 10 seconds (a pan, a cloth, etc.). A signal sounds and the hob deactivates. Remove the object or clean the control panel.
· the appliance gets too hot (e.g. when a saucepan boils dry). Let the cooking zone cool down before you use the hob again.
· you do not deactivate a cooking zone or change the heat setting. After some time, the hob deactivates.
The relation between the heat setting / fan speed setting and the time after which the appliance deactivates:

Heat setting 1 – 2

The hob deacti- vates after 6 hours

To exit the menu: press .
For more details on the settings and easier menu navigation download My Electrolux Kitchen .
OffSound Control
You can activate / deactivate the sounds in the Menu > User settings.
Refer to “Menu structure”.
When the sounds are off you can still hear the sound when: · you touch , · the timer comes down, · you press an inactive symbol.

Heat setting
3 – 4 5 6 – 9

The hob deacti- vates after 5 hours 4 hours 1.5 hours

Fan speed setting The hood deacti- vates after 10 hours

1 – 3

10 hours 10 minutes

7.2 Pause
This function sets all cooking zones that operate to the lowest heat setting. The speed of the hood fan decreases to 1. When you activate the function while the hood operates in the automatic mode, the speed of the hood fan will not be reduced.

18 www.electrolux.com
When the function operates, and can be used. All other symbols on the control panels are locked.
The function does not stop the timer functions.
1. To activate the function: press . The heat setting is lowered to 1. The speed of the hood fan decreases to 1. 2. To deactivate the function: press
. The previous heat setting / fan speed setting comes on.
7.3 Lock
You can lock the control panel while the hob operates. It prevents an accidental change of the heat setting / hood speed setting.
Set the heat setting / hood speed setting first.
To activate the function: press . To deactivate the function: press again.
The function deactivates as you deactivate the hob.
7.4 Child Safety Device
This function prevents an accidental operation of the hob and the hood.
To activate the function: press . Do not set any heat setting / hood setting. Press and hold for 3 seconds, until the indicator above the symbol appears. Deactivate the hob with .
The function stays active when you deactivate the hob. The indicator above is on.
To deactivate the function: press . Do not set any heat setting / hood setting. Press and hold for 3 seconds, until the indicator above the symbol disappears. Deactivate the hob with .

Cooking with the function activated: press , then press for 3 seconds, until the indicator above the symbol disappears. You can operate the hob. When you deactivate the hob with the function operates again.
7.5 Flexible induction cooking area
WARNING! Refer to Safety chapters.
FlexiBridge function
The flexible induction cooking area consists of four sections. The sections can be combined into two cooking zones with different size, or into one large cooking area. You choose the combination of the sections by choosing the mode applicable to the size of the cookware you want to use. There are three modes: Standard, Big Bridge, and Max Bridge.
To set the heat setting use the two control bars on the left side.
Switching between the modes
To switch between the modes press . The heat setting levels will be kept.
In some models there are two flexible cooking areas, left and right. To operate the flexible cooking area on the right side, use the symbols and the control bars on the right side of the hob.
Diameter and position of the cookware

Choose the mode applicable to the size and the shape of the cookware. The cookware should cover the selected area as much as possible.
Place the cookware with the bottom diameter smaller than 160 mm centrally on a single section. You can use a roaster pan for the Big Bridge and the Max Bridge modes.

ENGLISH 19
control bars on the left side.

Correct cookware position:

100-160mm
Place the cookware with the bottom diameter larger than 160 mm centrally between two sections.

Incorrect cookware position:

160 mm
FlexiBridge Standard mode
This mode is activated by default when you activate the function. It connects the sections into two separate cooking areas. You can set the heat setting for each area separately. Use the two

FlexiBridge Big Bridge mode
To activate the mode press until you
see the correct mode indicator . This mode connects the three rear sections into one cooking area. The front section is not connected and operates as a separate cooking zone. You can set the heat setting for each area separately. Use the two control bars on the left side.

20 www.electrolux.com
Correct cookware position: Make sure to place the cookware on the three connected sections. If you use cookware smaller than two sections the control bar blinks and after 2 minutes the zone deactivates.
Incorrect cookware position:
Incorrect cookware position:

FlexiBridge Max Bridge mode
To activate the mode press until you see the correct mode indicator . This mode connects all sections into one cooking area. To set the heat setting use any of the two control bars on the left side.
Correct cookware position: Make sure to place the cookware on the four connected sections. If you use cookware smaller than three sections the control bar blinks and after 2 minutes the zone switches off.

PowerSlide
This function allows you to adjust the temperature by moving the cookware to a different position on the induction cooking area.
· The function divides the induction cooking area into three areas with different heat settings. The hob detects the position of the cookware and adjusts the heat setting corresponding with the position.
· You can place the cookware in the front, middle or rear position. If you place the cookware in the front you get the highest heat setting. To decrease it, move the cookware to middle or rear position.
· When you activate the function for the first time you will get the following default heat settings: 9 for the front position, 6 for the middle position and 3 for the rear position.
· You can change the heat settings for each position separately. The hob will remember your heat settings next time you activate the function.

· The heat setting display of the left front control bar shows the heat setting for this function. To change the heat setting use the left front control bar only. The left rear control bar is deactivated while the function operates. In some models there are two flexible cooking areas, left and right. To operate PowerSlide on the right side, use the right front control bar.
Use only one pot with a minimum bottom diameter of 160 mm when you operate the function.
1. Place the correct cookware on the left front side of the cooking area.
2. Press and hold to activate the hob.
A signal sounds and indicators above and appear.
8. HINTS AND TIPS
WARNING! Refer to Safety chapters.
8.1 Cookware
For induction cooking zones a strong electro-magnetic field creates the heat in the cookware very quickly. Use the induction cooking zones with suitable cookware. · The bottom of the cookware must be as thick and flat as possible.

ENGLISH 21
3. Press to activate the function. A signal sounds and an indicator above the symbol appears. 4. Move the cookware back and forth
on the cooking area as needed. The heat setting level on the control bar adjusts automatically. 5. To change the default heat setting
levels, move the cookware to the area you want to adjust first. 6. Press any of the available heat setting levels on the left front control bar. The updated heat setting levels will be remembered for the next time you use the function. 7. Repeat the procedure for the remaining cooking areas, if needed. 8. To deactivate the function, press . You can also press 0 on the left front control bar. A signal sounds and the indicator above the symbol disappears. The heat setting level changes to 0. You can set a timer while PowerSlide operates. In this case the timer does not deactivate the cooking zones when the set time runs out. The timer affects all three cooking areas activated by the function at the same time.
· Ensure pan bases are clean and dry before placing on the hob surface.
· In order to avoid scratches, do not slide or rub the pot across the ceramic glass.
Cookware material · correct: cast iron, steel, enamelled
steel, stainless steel, multi-layer bottom (with a correct marking from a manufacturer). · not correct: aluminium, copper, brass, glass, ceramic, porcelain. Cookware is suitable for an induction hob if:

22 www.electrolux.com
· water boils very quickly on a zone set to the highest heat setting.
· a magnet pulls on to the bottom of the cookware.
Cookware dimensions
· Induction cooking zones adapt to the dimension of the bottom of the cookware automatically.
· The cooking zone efficiency is related to the diameter of the cookware. The cookware with a diameter smaller than the minimum receives only a part of the power generated by the cooking zone.
· For both safety reasons and optimal cooking results, do not use cookware larger than indicated in “Cooking zones specification”. Avoid keeping cookware close to the control panel during the cooking session. This might impact the functioning of the control panel or accidentally activate hob functions.
Refer to “Technical data”.
Steam Vented Lids
To further optimize the cooking sessions alongside the hood you can use the special Steam Vented Lids with your cookware. The lids are designed to direct the steam produced inside the pot towards the hood, minimizing unwanted cooking smells and excessive humidity in the kitchen. The lids are available to buy separately in several sizes to fit most common cookware types. For more information visit our website.

8.2 The noises during operation
If you can hear:
· crack noise: cookware is made of different materials (a sandwich construction).
· whistle sound: you use a cooking zone with a high power level and the cookware is made of different materials (a sandwich construction).
· humming: you use a high power level. · clicking: electric switching occurs. · hissing, buzzing: the fan operates. The noises are normal and do not indicate any malfunction.
8.3 Öko Timer (Eco Timer)
To save energy, the heater of the cooking zone deactivates before the count down timer sounds. The difference in the operation time depends on the heat setting level and the length of the cooking operation.
8.4 Examples of cooking applications
The correlation between the heat setting of a zone and its consumption of power is not linear. When you increase the heat setting, it is not proportional to the increase of the consumption of power. It means that a cooking zone with the medium heat setting uses less than a half of its power.
The data in the table is for guidance only.

ENGLISH 23

Heat setting Use to:

Time Hints (min)

1

Keep cooked food warm.

as nec- Put a lid on the cookware.

essary

1 – 2

Hollandaise sauce, melt: but- 5 – 25 Mix from time to time. ter, chocolate, gelatine.

1 – 2

Solidify: fluffy omelettes, baked eggs.

10 – 40 Cook with a lid on.

2 – 3

Simmer rice and milkbased dishes, heat up readycooked meals.

25 – 50

Add at least twice as much liquid as rice, mix milk dishes halfway through the procedure.

3 – 4

Steam vegetables, fish, meat.

20 – 45 Add a couple of tablespoons of liquid.

4 – 5

Steam potatoes.

20 – 60 Use max. ¼ l of water for 750 g of potatoes.

4 – 5

Cook larger quantities of food, stews and soups.

60 – Up to 3 l of liquid plus ingre-

150

dients.

6 – 7

Gentle fry: escalope, veal cordon bleu, cutlets, rissoles, sausages, liver, roux, eggs, pancakes, doughnuts.

as nec- essary

Turn halfway through.

7 – 8

Heavy fry, hash browns, loin 5 – 15 Turn halfway through. steaks, steaks.

9

Boil water, cook pasta, sear meat (goulash, pot roast), deep-fry chips.

Boil large quantities of water. PowerBoost is activated.

8.5 Hints and Tips for the hood
· The grid covering the hood is made of aluminium and stainless steel. You can put pots on it while the hood is not operating. It will not cause any damage.
· When AUTO mode operates, the fan starts at a low speed at the beginning of each cooking session. The speed
9. CARE AND CLEANING
WARNING! Refer to Safety chapters.
9.1 General information
· Clean the hob after each use.

increases gradually. You can also adjust the speed of the fan manually. · In case of exhaust installation you have to install a window switch. You need to buy it separately as it is not supplied with the hood. The window switch has to be installed by an authorised technician. Refer to the installation booklet.
· Always use cookware with a clean base.
· Scratches or dark stains on the surface have no effect on how the hob operates.
· Use a special cleaner suitable for the surface of the hob.

24 www.electrolux.com

· Use a special scraper for the glass.
The printing on the flexible induction cooking area may become dirty or change its colour from sliding the cookware. You can clean the area in a standard way.
9.2 Cleaning the hob
· Remove immediately: melted plastic, plastic foil, sugar and food with sugar, otherwise, the dirt can cause damage to the hob. Take care to avoid burns. Use a special hob scraper on the glass surface at an acute angle and move the blade on the surface.
· Remove when the hob is sufficiently cool: limescale rings, water rings, fat stains, shiny metallic discoloration. Clean the hob with a moist cloth and a non-abrasive detergent. After cleaning, wipe the hob dry with a soft cloth.
· Remove shiny metallic discoloration: use a solution of water with vinegar and clean the glass surface with a cloth.
9.3 Cleaning the hood
Grid The grid drives the air into the hood. Additionally, it protects the hood system and prevents foreign objects from falling inside by accident. You can wash the grid manually or in a dishwasher.
Water tank There is a water tank located under the hood. It collects the condensation created during each cooking process. Remember to empty the water tank regularly. To open the water tank, slide the latches out and open them one by one.

WARNING! Make sure you do not let water get inside the hood.
If water or other liquids spill inside the hood system:
· switch off the hood in the first place, · lift the grid and clean the hood area
carefully with a moist cloth or sponge and a mild cleaning agent, · wipe away the excess liquid gathered on the bottom of the hood cavity using a sponge or a dry cloth, · switch on the hood, set the fan speed level to 2 or higher and let it run for some time to get rid of the remaining moisture.
9.4 Cleaning the hood filter
The filter prevents grease particles from getting into the hood system. The hob has a built-in counter that reminds you about cleaning the filter. After 100 hours
of use the filter indicator starts blinking to signal that it is time to clean the filter. The notification stays on for 30 seconds after you deactivate the hood and the hob. The notification does not block the use of the hob.
It is recommended to clean the filter before the indicator appears.
1. Remove the filter and filter housing carefully. They are located right under the grid in the centre of the hob.

ENGLISH 25

2. Clean the hood cavity with a cleaning foam.
3. Wash the filter and filter housing manually in warm water without using detergents or abrasive sponges. You can also wash them in a dishwasher with the maximum temperature of 65-70 °C, without detergents and without dishes in the same load. Only the plastic parts can be cleaned using detergents.
10. TROUBLESHOOTING

4. Dry the filter for 7 minutes in an oven with the maximum temperature of 60°C or in an ambient temperature.
5. Fix the filter and filter housing back in place when they are fully dried.
6. Reset the counter. Resetting the counter when the filter indicator is on:
1. Clean the filter first and place it back inside the hood.
2. Press briefly, while the indicator is blinking. The counter restarts.
Resetting the counter before the filter indicator appears:
1. Make sure the hob is switched off and Child Safety Device does not operate.
2. Clean the filter and place it back inside the hood.
3. Press twice. The indicator appears and the signal sounds. The counter restarts.
The counter starts automatically when you turn on the hood for the first time. The maximum number of cleaning cycles is 8. After that time, the filter needs to be replaced with a new one.
WARNING! An oversaturated filter can pose a risk of fire.

WARNING! Refer to Safety chapters.

10.1 What to do if…

Problem
You cannot activate or operate the hob.

Possible cause
The hob is not connected to an electrical supply or it is connected incorrectly.

Remedy
Check if the hob is correctly connected to the electrical supply.

26 www.electrolux.com

Problem

Possible cause

Remedy

The fuse is blown.

Make sure that the fuse is the cause of the malfunction. If the fuse is blown again and again, contact a quali- fied electrician.

You do not set the heat setting for 60 seconds.

Activate the hob again and set the heat setting in less than 60 seconds.

You touched 2 or more sensor fields at the same time.

Touch only one sensor field.

Pause operates.

Refer to “Daily use”.

There is water or fat stains Clean the control panel. on the control panel.

You can hear a constant beep noise.

The electrical connection is incorrect.

Disconnect the hob from the electrical supply. Ask a quali- fied electrician to check the installation.

You cannot select the maximum heat setting for one of the cooking zones.

The other zones consume the maximum available power. Your hob works properly.

Reduce the heat setting of the other cooking zones con- nected to the same phase. Refer to “Power manage- ment”.

An acoustic signal sounds and the hob de- activates. An acoustic signal sounds when the hob is deactivated.

You put something on one or more sensor fields.

Remove the object from the sensor fields.

The hob deactivates.

You put something on the Remove the object from the

sensor field .

sensor field.

Residual heat indicator does not come on.

The zone is not hot be-

If the zone operated suffi-

cause it operated only for a ciently long to be hot, speak

short time or the sensor is to an Authorised Service

damaged.

Centre.

There is no sound when The sounds are deactiva- you touch the panel sen- ted. sor fields.

Activate the sounds. Refer to “Daily use”.

ENGLISH 27

Problem

Possible cause

Remedy

The flexible induction cooking area does not heat up the cookware.

The cookware is in a wrong Place the cookware in the

position on the flexible in- correct position on the flexi-

duction cooking area.

ble induction cooking area.

The position of the cookware

depends on the activated

function or function mode.

Refer to “Flexible induction

cooking area”.

The diameter of the bottom Use cookware with a diame-

of the cookware is incorrect ter applicable to the activa-

for the activated function or ted function or function

function mode.

mode. Refer to “Flexible in-

duction cooking area”.

The indicator above the Child Safety Device or

symbol comes on.

Lock operates.

Refer to “Daily use”.

The control bar blinks.

There is no cookware on Put cookware on the zone so

the zone or the zone is not that it fully covers the cook-

fully covered.

ing zone.

The cookware is unsuita- ble.

Use cookware suitable for in- duction hobs. Refer to “Hints and tips”.

The diameter of the bottom Use cookware with correct

of the cookware is too

dimensions. Refer to “Tech-

small for the zone.

nical data”.

FlexiBridge (Flexible Bridge) operates. One or more sections of the func- tion mode which operates are not covered by the cookware.

Place the cookware on the correct number of sections of the function mode which op- erates or change the func- tion mode. Refer to “Flexible induction cooking area”.

The control bar blinks twice and turns off.

PowerSlide operates. Two Use only one pot. Refer to pots are placed on the flex- “Flexible induction cooking ible induction cooking area area”. or the cookware covers more than one cooking area activated by the func- tion.

The control bar for hood The fan may turn off by it-

blinks and the hood does self in certain conditions,

not start or turns off.

e.g. when the room is not

properly ventilated.

Open the window (you may need to install the window switch, refer to “Hints and Tips for the Hood”). Press any symbol. The hood oper- ates again.

28 www.electrolux.com

Problem

Possible cause

Remedy

The hood fan does not work properly when the hood functions are acti- vated.

The ambient temperature Deactivate the hob and un-

surrounding the hood is too plug it from the main power

high.

supply. Wait at least 10 sec-

There is insufficient air cir- onds, then plug it in again.

culation inside and around Other suggestions:

the hood.

Try to cool down the temper-

ature of the surrounding

area. Take out the hood filter

and remove the residual

moisture from the inside of

the hood. Refer to “Care and

cleaning”. Leave the hood

system to dry for one day,

then activate the hood again.

The steam produced

The lids on the cookware

during cooking is not suf- are not properly placed.

ficiently absorbed by the

hood.

If your cookware does not have vented lids, make sure to tilt the lids so that the re- leased steam is directed to- wards the hood. Refer to “Hints and Tips” for information on the special Steam Vented Lids recom- mended to be used with the integrated hood.

The hood filter is oversatu- Clean the hood filter and re-

rated.

set the notification. Refer to

“Care and cleaning”.

and a number come on.

There is an error in the hob. For more details go to the app.

Deactivate the hob and acti- vate it again after 30 sec-
onds. If comes on again, disconnect the hob from the electrical supply. After 30 seconds, connect the hob again. If the problem contin- ues, speak to an Authorised Service Centre.

blinks.

The wireless connection is lost.

Restore the wireless connec- tion. Check your home net- work. If the problem persists, try to reconnect to the net- work. Refer to “Before first use” > “Changing the net- work”.

10.2 If you cannot find a solution…
If you cannot find a solution to the problem yourself, contact your dealer or

an Authorised Service Centre. Give the data from the rating plate. Make sure, you operated the hob correctly. If not the servicing by a service technician or dealer will not be free of charge, also

during the warranty period. The information about guarantee period and
11. TECHNICAL DATA
11.1 Rating plate

ENGLISH 29
Authorised Service Centres are in the guarantee booklet.

Model HHOF875S Typ 66 D4A 05 CA Induction 7.35 kW Ser.Nr. …………….. ELECTROLUX

PNC 949 599 204 00 220 – 240 V / 400 V 2N 50 Hz Made in: Germany 7.35 kW

11.2 Cooking zones specification

Cooking zone Nominal power PowerBoost

(maximum

[W]

heat setting)

[W]

Flexible induc- 2300 tion cooking area

3200

PowerBoost Cookware di- maximum du- ameter [mm] ration [min]

10

minimum 100

The power of the cooking zones can be different in some small range from the data in the table. It changes with the material and dimensions of the cookware.

For optimal cooking results use cookware no larger than the diameter in the table.

11.3 Main connectivity information

Frequency / protocol Max power Encryption

Wi-Fi

2.4 GHz / 802.11 bgn

Wi-Fi

5 GHz / 802.11 an (for indoor use only)

Bluetooth Low Energy 5.0 2.4 GHz / DSSS

Wi-Fi

2.4 GHz: <20 dBm

Wi-Fi

5 GHz: <23 dBm

Bluetooth Low Energy 5.0 <20 dBm

WPA, WPA2

Guidance on Article 10 (10) of RED (Directive 2014/53/EU) from November 5, 2020. List of countries: Belgium, Bulgaria, Czech Republic, Denmark, Germany, Estonia, Ireland, Greece, Spain, France, Croatia, Italy, Cyprus, Latvia, Lithuania, Luxembourg, Hungary, Malta, Netherlands, Austria, Poland, Portugal, Romania, Slovenia, Slovakia, Finland, Sweden, Norway, Iceland, Liechtenstein, Switzerland, Turkey and Northern Ireland.

30 www.electrolux.com
12. ENERGY EFFICIENCY
12.1 Product Information*

Model identification

Type of hob

Number of cooking areas

Heating technology

Length (L) and width (W) of the cooking

Left

area

Length (L) and width (W) of the cooking area

Right

Energy consumption of the cooking

Left

area (EC electric cooking)

Energy consumption of the cooking area (EC electric cooking)

Right

Energy consumption of the hob (EC electric hob)

HHOF875S Built-In Hob 2 Induction L 45.8 cm W 21.4 cm L 45.8 cm W 21.4 cm 191.1 Wh / kg
191.1 Wh / kg
191.1 Wh / kg

• For European Union according to EU 66/2014. For Belarus according to STB 2477-2017, Annex A. For Ukraine according to 742/2019.
  EN 60350-2 – Household electric cooking appliances – Part 2: Hobs – Methods for measuring performance.
  12.2 Energy saving
  You can save energy during everyday cooking if you follow below hints.

· When you heat up water, use only the amount you need.
· If it is possible, always put the lids on the cookware.
· Before you activate the cooking zone put the cookware on it.
· Put the smaller cookware on the smaller cooking zones.
· Put the cookware directly in the centre of the cooking zone.
· Use the residual heat to keep the food warm or to melt it.

13. ENVIRONMENTAL CONCERNS

Recycle materials with the symbol . Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances. Do not dispose of

appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.

867373207-A-472021

www.electrolux.com/shop

References

• Electrolux
• Electrolux
• Register Your Appliance – Product Registration – Electrolux

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>