CHROMEBATTERY YTX9-BS Intelligent Bluetooth Enabled Motorcycle Battery Module User Guide
- June 12, 2024
- CHROMEBATTERY
Table of Contents
Chrome Battery Now
Module Integration Guide
General
The Chrome Bluetooth Module is designed to comply with the FCC statement. The
Chrome Bluetooth
Module FCC ID is 2A8DV-BT2222.
List of application FCC rules
The module complies with FCC Part 15 Subpart B and FCC Part 15.247.
Summarize the specific operational use conditions
The radio module is restricted for use Chrome Battery Now products produced by
J-J.A.D.E. Enterprises
LLC. The installation and repair of the communication module may only be
performed by technical personal associated with J-J.A.D.E. Enterprises LLC.
The radio module must not be installed in a manner in which it is co-located
and operating simultaneously with other radios in the host system. If the
module is installed in a host system that includes other radios, additional
testing and equipment authorization will be required.
Limited Module Procedures
The radio module is restricted for use Chrome Battery Now products produced by
J-J.A.D.E. Enterprises LLC. The module has no RF shielding. The installation
and repair of the communication module may only be performed by technical
personal associated with J-J.A.D.E. Enterprises LLC.
Trace antenna designs
The module does not have a trace antenna.
RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines. This equipment should be installed and operated keeping the
radiator at least 20cm or more away from person’s body
Antennas:
The device is designed to use the antennas listed below. Do not modify the
antenna or any other part of the module. Any modifications will invalidate the
modular certifications and require new approvals for the host system.
Part No: Yageo ANT3216LL00R2400A
Type: Chip Antenna
Peak Gain: 5.05dBi
Label and compliance information
The host system using the module should have a label indicating the modular
FCC ID: 2A8DV-BT2222.
Information on test modes and additional testing requirements
Test modes for the host device should take into consideration different
operational conditions for a stand-alone modular transmitter in a host. The
host manufacturer may operate their product during the measurements. The host
product manufacturer should coordinate with the module manufacturer for
instructions to put the device into test modes.
Additional testing, Part 15 Subpart B disclaimer
The modular transmitter is only FCC authorized for the specific rule parts
(FCC Part 15.247) list on the grant, and that the host product manufacturer is
responsible for compliance to any other FCC rules that apply to the host not
covered by the modular transmitter grant of certification. The final host
product still requires Part 15 Subpart B compliance testing with the modular
transmitter installed when contains digital circuitry.
Note EMI Considerations
We recommend to use “best practice” RF design engineering testing and
evaluation in case non-linear interactions generate additional non-compliant
limits due to module placement to host components or properties.
The host manufacturer is responsible for ensuring compliance with the
applicable FCC rules for the transmitters operating individually and
simultaneously. This includes compliance for the summation of all emissions
from all outputs occupying the same or overlapping frequency ranges, as
defined by the applicable rules.
How to make changes
Only Grantees are permitted to make permissive changes.
Module Integration Instructions
The procedure for installing this module on the host device is described
below.
Supply Voltage: The module contains a voltage regulator and can be supplied
with any DC voltage that does not exceed 15V. In order to function properly,
the supply voltage must be at least 3.3V. Power should be supplied to the pads
labeled “VBAT+” and a ground connection should be made on the pad labeled
“GND-“.
Physical installation: The module should be housed in a manner in which it is
not exposed to the environment and limits movement of the module within the
housing. The housing must cover the entire module and be made of a material
(e.g. plastic) that prevents any part of the module, component on the module,
or its wiring, from making any contact (electrical or otherwise) with anything
outside of the housing.
Restrictions: The radio module is restricted for use Chrome Battery Now
products produced by J-J.A.D.E.
Enterprises LLC. The installation and repair of the communication module may
only be performed by technical personal associated with J-J.A.D.E. Enterprises
LLC.
The radio module must not be installed in a manner in which it is co-located
and operating simultaneously with other radios in the host system. If the
module is installed in a host system that includes other radios, additional
testing and equipment authorization will be required.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>