HOOVER HVG7W4BSB Gas Hob Instruction Manual

HOOVER HVG7W4BSB Gas Hob

Product Information

This product is a cooking appliance designed for domestic use. It can be connected to the electrical and gas supply in your home. Please follow the safety instructions and user instructions provided below to ensure safe and proper usage of the product.

Safety Instructions

• Ensure that the electrical and gas connections are done by a qualified installer.
• Do not use earth leakage devices with electric cooking appliances installed to spur points.
• Check for gas leaks using a soapy solution, never use a flame.
• If gas can be smelt in the vicinity of the appliance, turn off the gas supply and call an engineer.
• Do not use the appliance for any purpose other than domestic cooking.
• Do not use vessels with a concave or convex base on the gas burner.
• If a flame is accidentally extinguished, wait for at least 1 minute before attempting to re-ignite.
• If the gas taps become stiff to turn, lubrication should only be done by qualified service engineers.

Electrical Connection
The electrical connection should be done as follows:

• Green & Yellow Wire: Earth Connection
• Blue Wire: Neutral Connection
• Brown Wire: Live Connection

Gas Connection

The gas connection should be done as follows:

1. Assemble the parts in sequence: 1/2 Male Adaptor Cylindrical, 1/2 Seal, 1/2 Female Gas Adaptor Conical-Cylindrical or Cylindirical-Cylindirical.
2. Tighten the joints with a spanner.
3. Attach fitting C to the mains gas supply using rigid copper pipe or flexible steel pipe.
4. Check for leaks on the pipe connections using a soapy solution. Do not use a flame.
5. Ensure that the flexible pipe is not in contact with any moving part of the cabinet and is not situated where it could be damaged.

Product Usage Instructions
Before using the burner, ensure that the grid perimeter centers the burner as shown in the figure. If you are using cast iron grids, position them correctly underneath the grid as stated. Use the table below to regulate the gas burner based on the type of burner and the desired flame:

429
DC 4,5 kW Mono| 16 – 26| 4,50| 400

The gas burner should be regulated so that the flame does not overlap the base of the pan. Do not use vessels with a concave or convex base. If a flame is accidentally extinguished, turn the knob to the off position and wait for at least 1 minute before attempting to re-ignite. If over the years the gas taps become too stiff to turn, lubrication should only be done by qualified service engineers.

SAFETY INSTURUCTIONS

We recommend you keep the instructions for installation and use them for later reference, and before installing the hob, note its serial number in case you need to get help from the after-sales service. WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children under 8 years of age must be kept away from the appliance unless they are continuously supervised.
WARNING: Use only hob guards designed by the Manufacturer of the cooking appliance or indicated by the Manufacturer of the appliance in the instructions for use as suitable hob guards incorporated in the appliance. The use of inappropriate guards can cause accidents. WARNING: unattended cooking on a hob with fat or oil can be dangerous and may result in fire. NEVER try to extinguish a fire with water, but switch off the appliance and then cover the flame e.g. with a lid or a fire blanket.
WARNING: danger of fire: do not store items on the cooking surfaces.
WARNING: If the surface is cracked, do not touch the glass and switch off the appliance to avoid the possibility of electric shock.

This appliance can be used by children aged 8 years and above and people with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision.

CAUTION: The cooking process must be supervised. A short-term cooking process has to be supervised continuously. It is strongly recommended to keep children away from the cooking zones while they are in operation or when they are switched off, so long as the residual heat indicator is on, in order to prevent the risks of serious burns. This appliance is not intended to be operated by means of an external timer or a separate remote control system.

If present do not stare into halogen lamp hob elements. Connect a plug to the supply cable that is able to bear the voltage, current, and load indicated on the tag and have the earth contact. The socket must be suitable for the load indicated on the tag and must be having the earth contact connected and in operation. The earth conductor is yellow-green in color. This operation should be carried out by a suitably qualified professional. In case of incompatibility between the socket and the appliance plug, ask a qualified electrician to substitute the socket with another suitable type. The plug and the socket must conform to the current norms of the installation country. Connection to the power source can also be made by placing an omnipolar breaker between the appliance and the power source that can bear the maximum connected load and that is in line with current legislation.

The yellow-green earth cable should not be interrupted by the breaker. The socket or omnipolar breaker used for the connection should be easily accessible when the appliance is installed. The disconnection may be achieved by having the plug accessible or by incorporating a switch in the fixed wiring in accordance with the wiring rules. If the supply cord is damaged, it must be replaced by the Manufacturer, its service agent, or similarly qualified people in order to avoid a hazard. The earth conductor (yellow-green) must be longer than 10 mm on the terminal block side. The internal conductors section should be appropriate to the power absorbed by the hob (indicated on the tag). The type of power cable must be H05 GG-F for 60-75cm hobs or H05-V2V2-F for 75cm hobs. Do not put metallic objects such as knives, forks, spoons, or lids on the hob. They could heat up. Aluminum foil and plastic pans must not be placed on heating zones. After every use, some cleaning of the hob is necessary to prevent the build-up of dirt and grease. If left, this is recooked when the hob is used and burns giving off smoke and unpleasant smells, not to mention the risks of fire propagation.

• Never use a steam or high-pressure spray to clean the appliance.
• Do not touch the heat zones during operation or for a while after use.
• Never cook food directly on the glass ceramic hob.
• Always use the appropriate cookware. Always place the pan in the center of the unit that you are cooking on.
• Do not place anything on the control panel.
• Do not use the hob as a working surface.
• Do not use the surface as a cutting board.
• Do not store heavy items above the hob. If they drop onto the hob, they may cause damage.
• Do not use the hob for storage of any items.
• Do not slide cookware across the hob.
• No additional operation/setting is required in order to operate the appliance at the rated frequencies.

In case of hotplate glass breakage
Shut immediately off all burners and electrical heating elements and isolate the appliance from the power supply. Do not touch the appliance surface. Do not use the appliance.

INSTRUCTIONS FOR THE INSTALLER
INSTALLING A DOMESTIC APPLIANCE CAN BE A COMPLICATED OPERATION THAT IF NOT CARRIED OUT CORRECTLY, CAN SERIOUSLY AFFECT CONSUMER SAFETY. IT IS FOR THIS REASON THAT THE TASK SHOULD BE UNDERTAKEN BY A PROFESSIONALLY QUALIFIED PERSON WHO WILL CARRY IT OUT IN ACCORDANCE WITH THE TECHNICAL REGULATIONS IN FORCE. IN THE EVENT THAT THIS ADVICE IS IGNORED AND THE INSTALLATION IS CARRIED OUT BY AN UNQUALIFIED PERSON, THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR PRODUCT WHETHER OR NOT THE RESULTS IN INDIVIDUALS

BUILDING IN

The hob may be installed in any worktop that is heat resistant to a temperature of 100°C and has a thickness of 25-45 mm. The dimensions of the insert to be cut out of the worktop are shown in Figure 2. When there is an accessible space between the built-in hob and the cavity below, a dividing wall made of insulating material should be inserted (wood or similar material) (Figure 2). If the Hob is fitted next to a cabinet on either side, the distance is between 70 mm. The distance between the hob and any other unit or appliance above it (e.g.An extractor hood) must be no less than 70 cm (Figure 4). Metal objects in the drawer may reach high temperatures due to air recirculation. It is therefore recommended to use an intermediate wood panel. Important – The diagram in Figure 1 shows how the sealant should be applied. The Hob unit is fitted by attaching the Fixing Clamps supplied, using the holes at the base of the unit. When a 60 cm hob or a 75 cm hob is fitted over a built-in oven, the latter must be fan-cooled.

SUITABLE LOCATION
This appliance must be installed in accordance with the regulations in force and only used in a well-ventilated space. Read the instructions before installing or using this appliance. A gas-powered cooking appliance produces heat and humidity in the area in which it is installed. For this reason, you should ensure good ventilation either by keeping all-natural air passages open or by installing an extractor hood with an exhaust flue. Intensive and prolonged use of the appliance may require extra ventilation, such as the opening of a window or an increase in the speed of the electric fan if you have one. If a hood can not be installed, an electric fan should be fitted to an outside wall or window to ensure that there is adequate ventilation. The electric fan should be able to carry out a complete change of air in the kitchen 3-5 times every hour. The installer should follow the relevant national standards.

ELECTRICAL CONNECTION (FOR U.K. ONLY)
Warning – This appliance must be earthed
This appliance is designed for domestic use only. Connection to the main supply must be made by a competent electrician, ensuring that all current regulations concerning such installations are observed.
The appliance must only be connected to a suitably rated spur point, a 3-pin 13 amp plug/socket is not suitable. A double pole switch must be provided and the circuit must have appropriate fuse protection. Further details of the power requirement of the individual product will be found in the users’ instructions and on the appliance rating plate. In the case of built-in products you are advised, should you wish to use a longer cable than the one supplied, that a suitably rated heat-resistant type must be used. The wiring must be connected to the mains supply as follows: The wiring must be connected to the mains supply as follows:

CONNECT TOSPURTERMINAL

• Green &Yellow Wire Earth Connection
• Blue Wire Neutral Connection
• Brown Wire Live Connection

Note: We do not advocate the use of earth leakage devices with Electric cooking appliances installed to spur points because of the «nuisance tripping» that may occur. You are again reminded that the
The appliance must be correctly earthed, the manufacturer must decline any responsibility for any event occurring as a result of incorrect electrical installation.

ELECTRICAL CONNECTION
Check the data on the rating plate, located on the outside of the unit, to ensure that the supply and input voltage are suitable. By Law, this appliance must be earthed. If this regulation is not complied with, the Manufacturer will not be responsible for any damage caused to persons or property. If a plug is not already attached, fit a plug appropriate to the load indicated on the rating plate. The earth wire is colored yellow/green. The plug should always be accessible. If the power supply cord is damaged this is to be replaced by a qualified engineer so as to prevent any potential risk. Where the Hob is connected directly to the electricity supply, a circuit breaker must be fitted.

The section of the cable used must be of the correct size in relation to the absorbed power of the hob. Please check the rating plate for the power details and ensure that the power supply cord is of the type 3×0.75 mm² for 60-75cm hobs or H05-V2V2-F for 75cm hobsIf an appliance is not fitted with a supply cord and a plug, or with other means for disconnection from the supply mains having a contact separation in all poles that provide full disconnection under overvoltage category III conditions, the instructions shall state that means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

GAS CONNECTION

These instructions are for qualified personnel, installation of equipment must be in line with the relevant national standard. (For U.K. only: by law, the gas installation\commissioning must be carried out by a “Gas Safe” installer) All work must be carried out with the electricity supply disconnected. The rating plate on the hob shows the type of gas with which it is designed to be used. Connection to the mains gas supply or gas cylinder should be carried out after having checked that it is regulated for the type of gas with which it will be supplied. If it is not correctly regulated see the instructions in the following paragraphs to change the gas setting. For liquid gas (cylinder gas) use pressure regulators which comply with the relevant national standards. Use only pipes, washers, and sealing washers that comply with the relevant national standards. For some models a conic link is furnished to outfit for the installation in the countries where this type of link is obligatory; in picture 8 it is pointed out how to recognize the different types of links (CY = cylindrical, CO = conic). In every case, the cylindrical part of the link has to be connected to the hob. When connecting the hob to the gas supply via the use of flexible hoses please ensure that the maximum distance covered by the hose does not exceed 2 metres. The flexible tube shall be fitted in such a way that it cannot come into contact with a moveable part of the housing unit (e.g. a drawer) and does not pass through any space where it may become crushed/ kinked or damaged in any way. To prevent any potential damage to the hob please carry out the installation following this sequence (picture 6):
1)As illustrated, assemble parts in sequence:

• 1/2 MaleAdaptor Cylindrical
• 1/2 Seal
• 1/2 Female GasAdaptor Conical-Cylindirical or Cylindirical-Cylindirical2) Tighten the joints with the spanner, remembering to twist the pipes into position.
• Attach fitting C to the mains gas supply using rigid copper pipe or flexible steel pipe.

IMPORTANT : Carry out a final check for leaks on the pipe connections using a soapy solution. NEVER USE A FLAME. Also, make sure that the flexible pipe cannot come into contact with a moving part of the cabinet (eg. a drawer) and that it is not situated where it could be damaged.
Warning: If gas can be smelt in the vicinity of this appliance turn off the gas supply to the appliance and call the engineer directly. Do not search for a leak with a naked flame.

ADAPTING THE HOB TO DIFFERENT TYPES OF GAS
To adapt the Hob for use with different types of gas, carry out the following instructions:

• Remove the grids and burners
• Insert on hexagonal spanner (7 mm) into the burner support (Figure)
• Unscrew the injector and replace it with one suitable for the gas to be used (see gas type table)

REGULATING THE MINIMUM FLAME
After lighting the burners, turn the control knob to the minimum setting and then remove the knob (this can easily be removed by applying gentle pressure). Using a small «Terminal» type screwdriver the regulating screw can be adjusted as in Figure 9. Turning the screw clockwise reduces the gas flow, whilst turning it anticlockwise increases the flow – Use this adjustment to obtain a flame of approximately 3 to 4 mm in length and then replace the control knob. When the gas supply available is LPG – the screw to set the idle flame must be turned (clockwise) to the end stop. When you have carried out the new gas regulation, replace the old gas rating plate on your appliance with one (supplied with a hob) suitable for the type of gas for which it has been regulated.

USE OF HOB – USER INSTRUCTIONS
This appliance must only be used for the purpose for which it is intended, domestic cooking, and any other use will be considered improper and could therefore be dangerous. The Manufacturer will not be responsible for any damage or loss resulting from improper use. Before using the burner, be sure, that grid perimeters center the burner as below figure. If you are using Cast Iron Grids; underneath the grid, the position of it is stated. Be sure that the exact grid is used in the correct position.

USING THE GAS BURNER
Prior to switching on the gas hob ensure that the burners and burner caps are correctly placed in their position. This hob is fitted with electronic ignition to ignite the burner. To ignite the burners carry out the following: ° push in and turn the knob anticlockwise to the larger flame symbol and keep pushing 5 s after ignition. The ignition system will continue to generate sparks as long as the control knob is being pressed Warning: If there is no electricity on the appliance to ignite the burner a match or a lighter should be used to carry out the following: °place a lighted match or lighter close to the burner °push in and turn the knob anticlockwise to the larger flame symbol and keep pushing 5 s after ignition. Warning: In any case If after 5 s the burner has not lit, stop operating the device and wait at least 1 minute before attempting a further ignition of the burner.

GENERAL ADVICE
For best results, use cooking vessels with a flat surface. The size of the surface should match the gas burner side as follows. TableA. Table A The gas burner should be regulated so that the flame does not overlap the base of the pan. Vessels with a concave or convex base should not be used.
WARNING: If a flame is accidentally extinguished, turn the knob to the off position and do not attempt to re-ignite if for at least 1 minute. If over the years the gas taps become stiff to turn it is necessary to lubricate them. Such operation must be carried out only by qualified Service Engineers.

Burner Type| Ø pan/pot (cm)| Power (kW)| G20 20 mbar (methane)| G30 28-30 mbar (LPG)
---|---|---|---|---
AUX Auxiliary| 10 – 18| 1,00| 95 l/h| 73 g/h
SR Semi Rapid| 12 – 22| 1,75| 167 l/h| 127 g/h
R ** Rapid| 16 – 26| 2,70| 257 l/h| 196 g/h
DC 4 kW Mono| 16 – 26| 4,00| 381 l/h| 291 g/h
DC** 4,2 kW Mono| 16 – 26| 4,20 NG

4,00 LPG

| 400 l/h| 291 g/h
DC 4,5 kW Mono| 16 – 26| 4,50| 429 l/h| 327 g/h

MAINTENANCE AND CLEANING

Before cleaning the hob, ensure the appliance has cooled down. Remove the plug from the socket or (if connected directly) switch off the electricity supply. Cleaning and user maintenance shall not be made by children without supervision Never use abrasives, corrosive detergents, bleaching agents, or acids. Avoid any acid or alkaline substances (lemon, juice, vinegar, etc.) on the enameled, varnished, or stainless steel sections. When cleaning the enameled, varnished, or chrome sections, use warm soapy water or a noncaustic detergent. For stainless steel use an appropriate cleaning solution. The burners can be cleaned with soapy water. To restore their original shine, use a household stainless steel cleaner. After cleaning, dry the burners and replace them. It is important the Burners are replaced correctly.

Chromed grids and burners
Chromed grids and burners have a tendency to discolor with use. This does not jeopardize the functionality of the hob. Our After Sales Service Centre can provide spare parts if required.

AFTERCARE

• Before calling out a Service Engineer please check the following: that the plug is correctly inserted and fused; and that the gas supply is not faulty.
• Switch off the appliance and call the After Service Centre. DO NOT TAMPER WITH THE APPLIANCE.

PROTECTION OF THE ENVIRONMENT

This appliance is labeled in accordance with European Directive 2012/19/EU regarding electric and electronic appliances (WEEE). The WEEE contains both polluting substances (that can have a negative effect on the environment) and base elements (that can be reused). It is important that the WEEE undergoes specific treatments to correctly Remove and dispose of the pollutants and recover all the materials. Individuals can play an important role in ensuring that the WEEE does not become an environmental problem; it is essential to Follow a few basic rules

• The WEEE should not be treated as domestic waste;
• The WEEE should be taken to dedicated collection areas managed by the town council or a registered company.

In many countries, domestic collections may be available for large WEEEs. When you buy a new appliance, the old one can be returned to the vendor who must accept it free of charge as a one-off, as long as the appliance is of an equivalent type and has the same functions as the purchased appliance.

SAVING AND RESPECTING THE ENVIRONMENT
Where possible use a lid to cover the pan. Regulate the flame to not overlap the diameter of the pan.

DECLARATION OF COMPLIANCE
The appliance complies with European Directive 2009/142/EC (GAD) and starts from 21/04/2018 with Gas Appliances Regulation 2016/426 (GAR). By placing the mark on the product, we are confirming compliance with all relevant European safety, health, and environmental requirements that are applicable in legislation for this product.

Table 1

Burner Plate| 4Gas – L1 – STD| 4Gas – L2 – Diamond| 4Gas – L3 – Big Rear| 4Gas – L4 – Big Front| 5Gas – L5 – Central| 5Gas – L6 – 4+1
---|---|---|---|---|---|---
Burner| AUX/SR/2R| AUX/SR/2R| AUX/SR/R/DC| AUX/SR/R/DC| AUX/SR/2R/DC| AUX/SR/2R/DC
Type| PVUH60MF| PVUH60MF| PVUH60MF| PVUH60MF| PVUH75MF| PVUH75MF
FFD| YES| YES| YES| YES| YES| YES
AUX 1kW| 1| 1| 1| 1| 1| 1
SR 1,75 kW| 2| 1| 1| 1| 1| 2
R 2,7 kW| 1| 2| 1| 1| 2| 1
DC 4 kW Mono| –| –| 1| –| –| –
DC 4,2 kW Mono| –| –| –| 1| –| 1
DC 4,5 kW Mono| –| –| –| –| 1| –
Nominal Heat Input| 7,2kW| 8,15kW| 9,45kW| NG 9,65 kW LPG

9,45kW

| 12,65kW| NG 11,4kW

LPG 11,2kW

G20/20 mbar| 686 l/h| 776 l/h| 900 l/h| 920 l/h| 1204 l/h| 1085 l/h
G30/28-30 mbar| 524 g/h| 593 g/h| 688 g/h| 688 g/h| 920 g/h| 814 g/h
Installation Class| 3| 3| 3| 3| 3| 3
Voltage V/Frequency Hz| 220-240V 50/60Hz| 220-240V 50/60Hz| 220-240V 50/60Hz| 220-240V 50/60Hz| 220-240V 50/60Hz| 220-240V 50/60Hz
Electrical Input Power| 1| 1| 1| 1| 1| 1
Electric Ignition| YES| YES| YES| YES| YES| YES
Product Dimension| 595x505x42| 595x505x42| 595x505x42| 595x505x42| 745x505x42| 745x505x42

The manufacturer will not be responsible for any inaccuracy resulting from printing or transcript errors contained in this brochure. We reserve the right to carry out modifications to products as required, including the interests of consumption, without prejudice to the characteristics relating to safety or function.

References

• Hoover - Yenilik Hayat Buldu | Hoover

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>