Trust ACDB-8000A Wireless Doorbell User Manual
- June 12, 2024
- Trust
Table of Contents
Trust ACDB-8000A Wireless Doorbell User Manual
ACDB-8000A PUSH BUTTON FOR WIRELESS DOORBELL
-
Remove battery strip before use
A Insert a flat head screwdriver into the notch on the bottom of the push button and slide the push button off the back plate
B Open the waterproof rubber by flipping it open to show the battery
C Remove the plastic battery strip.
D Close the waterproof rubber and place the push button back on the back plate. -
Pair push button with a receiver While the receiver is in learn mode, send an ON signal to pair the push button with the receiver.
Refer to manual of the receiver to activate the learn mode. -
3A. Mount the push button with double-sided tape Determine where the push button should be placed. Stick the supplied double-sided tape on the back and attach the push button.
3B. Mount the push button with screws
A Insert a flat head screwdriver into the notch on the bottom of the push button and slide the push button off the back plate
B Determine where the push button should be placed and mount the back plate with the supplied screws.
C Place the push button back on the back plate by sliding it from top to bottom on the back plate.
Replace the battery
When the battery is almost empty, the LED will light up for 2 seconds and then
flash 3x after pressing the push button. A Insert a flat head screwdriver into
the notch on the
bottom of the push button and slide the push button off the back plate B Open
the waterproof rubber by flipping it open to show the battery C Take out the
old battery and insert a new CR2032 battery. Note that the + side points
upwards. D Close the waterproof rubber and place the push button back on the
back plate.
Combining Push Button with the Internet Control Station (ICS-2000) or Smart
Bridge
Combine the push button with the Internet Control Station (ICS-2000) or Smart
Bridge and receive a push notification on your smartphone when the doorbell
rings. For example, this way you can easily create a silent doorbell.
Safety Instructions
Product support: www.trust.com/71272. Warranty conditions: www.trust.com/warranty To ensure safe handling of the device, follow the safety advice on: www.trust.com/safety The Wireless range is strongly dependent on local conditions such as the presence of HR glass and reinforced concrete Never use Trust Smart Home products for life-support systems. This product is water-resistant. Do not attempt to repair this product. Wire colors may vary per country. Contact an electrician when in doubt about wiring. Never connect lights or equipment that exceed the maximum load of the receiver. Exercise caution when installing a receiver voltage may be present, even when a receiver is switched off. Maximum radio transmit power: 7.21 dBm. Radio transmission frequency range: 433,92 MHz
TECHNICAL SPECIFICATIONS Push button
www.trust.com/compliance
www.trust.com/compliance
Declaration of Conformity
Trust International B.V. declares that this Trust Smart Home-product:
Model: ACDB-8000A PUSH BUTTON FOR WIRELESS DOORBELL
Item number: 71272/71272-02/71276/71276-02
Intended use: Outdoor is in compliance with the essential requirements and
other relevant provisions of the following directives:
ROHS 2 Directive (2011/65/EU)
RED Directive (2014/53/EU)
The full text of the EU declaration of conformity is available at the
following web address:
www.trust.com/compliance
TRUST SMART HOME
LAAN VAN BARCELONA 600
3317DD DORDRECHT
NEDERLAND
www.trust.com
Trust Electronics Ltd.,
Sopwith Dr, Weybridge, KT13 0NT, UK.
All brand names are registered trademarks of their respective owners.
Specifications are subject to change
without prior notice. Made in China.
References
- Trust.com - Home
- Trust.com - Home
- Trust.com - ACDB-8000A Wireless push button
- Trust.com - Contact & Support - Compliance
- Trust.com - Contact & Support - Safety information
- Trust.com - Contact & Support - Warranty conditions
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>