LeafBlaster PRO Stainless Steel Micro Mesh Gutter Guard User Guide
- June 12, 2024
- LeafBlaster PRO
Table of Contents
Stainless Steel Micro Mesh Gutter Guard
User Guide
Stainless Steel Micro Mesh Gutter Guard
Install & Users Guide
LeafBlasterPRO is a stainless steel micro mesh gutter guard that installs on
any gutter and roof configuration. Its pa-tented V-Bend Technology in the mesh
allows for adaptability on any gutter-to-roof installation. Below are a few
roof type examples. Additional information available at
LeafBlasterPro.com. 
Important information in freezing condi-tions to share with
customer:
The following issues can occur with a gutter guard that are installed in areas
that are prone to freezing.
ICICLES & ICE DAMS can form on your gutter during freezing conditions. Ice
dams can cause water to leak back into your home. Icicles can break and cause
serious bodily harm.
SNOW MELTING and running down your
roof can run off the side of the gutter and refreeze on the ground below.
Water frozen on surfaces can create slipping hazards and cause serious bodi-ly
harm.
STEP 1: Choose your gutter and roof configuration
Select the diagram below that best resembles the gutter and roof scenario.
This determines whether you slide the gutter guard under the roof shingles or
bend the mesh up or down and fasten to the fascia. The diagrams all refer to a
roof shingle and gutter, they imply ALL shingle and gutter types.
Roof Shingle
| Asphalt | Standing Jock seam |
|---|---|
| Flat tle | Wood shake |
| Spanish tile | Membrane |
| Villa tile | Stone coated steef |
| Fiat roof | Corrugated steel |
Gutter
| Ogee | Fascia |
|---|---|
| Curved | Haif Round |
Traditional gutter and roof:
Gutter guard slides under shingles.
Gutter hung tow, or a flat roof:
Bend mesh either up or down, whichever is more convenient, then fasten to the
gutter or fascia with screws.
Steep roof:
You may have to bend the mesh up to slide it under the roof, or you could bend
it down and fasten to the gutter with screw:
INSTALL TIP: 3 setf-tapping screws per 4 foot section (Additional screws
may be needed for back extrusion).
Roof
Ramping: If the gutter guard causes the shingles to ramp up, then bend the
mesh down and then slide back under the shingle. You can also follow the
options on Diagram B. This can occasionally happen on a low hanging gutter.
STEP 2: The Basics
JOINING SECTIONS
Trim off the mesh that extends past the frame on the front rail Overlap
sections together on top of each other.
CUTTING SECTIONS
Cut front & back aluminum frame. Cut mesh. Snap in two.
INSIDE MITER
Trim off aluminum ends, exposing mesh. Tuck mesh down inside gutter adjacent
to adjoining miter.
OUTSIDE MITER
Bend one section down in gutter to allow room for adjoining section. Cut
adjoining section at 45 degrees.
END CAP
Trim off aluminum ends and then tuck mesh inside gutter.
STEP 3: Do not miss this step!
Follow these two rules so rainwater flows smoothly into your gutter and not
over the front edge of the gutter.
RULE #1
Remove gap: Make sure the front lip of the gutter guard is flat against
the front lip of your gutter to remove any gap.
RULE #2
Trough depth: The stainless steel mesh trough must be at least 118th of an
inch below the front lip of the gutter. It generally lays naturally like this,
but sometimes you need to push the mesh trough down just a little. This can
happen on steeply pitched roofs or gutters that are hung low (1 inch or
greater) below roofline.
Actual photos of gutter guard on top front lip of gutter
How To Bend The Mesh
BENDING THE MESH
Bending the back of the mesh UP or DOWN allows it to be installed on many
types of roofs where the gutter is lowered or where the roofing material is
fastened down to the roof deck.
Bending UP
The mesh can be bent up for installing on lowered gutters or flat
roofs.
Bending DOWN
The mesh can be bent down for installing on roofing materials that are
permanently fastened to the roof deck.
40 Year Limited Parts Warranty
Gutterglove, Inc. (herein referred to as GGI) warrants to the original
purchaser that its specially designed LeafBiasterPRO gutter guard will be free
from defects in manufactured parts, and agrees that it will, at its optic”
only, either repair the defect or replace the defective part thereof with a
new or reconditioned equivalent.
This limited Warranty is valid for 40 (forty) years for parts only and does
not include cost of labor for re- installatation. In coastal areas, warranty
is reduced to 10 (ten) years for parts only. “Coastal areas” is defined as
anyshere within 5 (five) miles of the coast. Shipping costs will be absorbed
by the purchaser of Los’SlasterPRO. The above named item is subject to the
following terms and conditions. No other warranty is con-gssed or implied in
this Limited Warranty.
Coverage Exclusions and Limitations: The above mentioned warranties are void
if any of the following concians occur. Improper installation; Settlement of
building structure; Structural shrinkage or distortion of structure (Example.
warping of roof or gutter over time, etc.); Vandalism; Hail; Fire; Tornado;
Windstorm; Earthquakes; Lightning; Protective liquids or any type of roof
preservation product applied to roof tops to extend the life of a roof,
Maintenance procedures are not followed properly, Tree sapping on mesh;
Insect/bird droppings on mesh; Accidental damage; Acts of God; Misuse or abuse
of the gutter guard; Mildew accumulation; Paint overspray, Moss accumulation;
Impact of foreign objects; Caustic atmospheric conditions (Example: Acid rain,
harmful chemicals, salt spray, etc.) or any other causes beyond the control of
GGI. It is the owner(s) responsibility to unclog the mesh in the event it gets
clogged. Icicles can form, and ice can form on top of LeafBlasterPRO in
extreme cold weather where snow is present.
GGI’s obligation under this warranty shall at no time exceed the original
purchase price of this product at time of sale, but not for installation or
re-installation costs. These warranties cover only LeafBlasterPRO gutter
guards and do not cover the gutter or any part of the building structure.
GGI reserves the right to withdraw this warranty from the market at any time.
Any and all warranties in effect at the time of removal will not be affected
by the withdrawal, and will remain in effect until their expiration. This
warranty is transferrable to any new property.
GGI will not be liable to you or any subsequent owner(s) for a breach of any
written or oral express warranties, such as those given to you by a
contractor, sub-contractor or installer. Any implied warranties imposed by
law, such as the implied warranties of merchantability and fitness for a
particular purpose are limited in time to the duration of this express
warranty. GGI shail not be liable for any consequential damages for breach of
any exPress, written, oral, or implied warranty on any LeafBlasterPRO gutter
guard. Your exclusive remedy shall be repair or replacement solely at GGi’s
option, only on terms stated in the warranties.
Activation of Warranty: This warranty becomes effective at time of
purchase. Retain this document with original purchase receipt. Failure to do
so will render this warranty null and void.
Claims Procedure: Any claim made hereunder must be presented to GGI
within the warranty period within a reasonable period of time after
discovering the defect. The claim should make reference to original date Of
installation, the purchaser’s name, address, phone number and a copy of the
original receipt.
Contact LeafBlasterPRO at 866-483-8166
or by mail to Gutterglove, Inc., 8860 industrial Avenue, Suite 140,
Rosaville, California 95678.
SUPPORT: 866-483-8166
customerservice@gutterglove.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>