DVIGEAR Wildcat 4K HDMI CAT6 Extender Set User Guide

DVIGEAR Wildcat 4K HDMI CAT6 Extender Set

Product Information

source
| – Supports pass-through of embedded HDMI audio, including LPCM
2.0/2.1/5.1/6.1/7.1 and HBR Bitstream formats
| – Analog Audio Output: Supports Stereo Linear PCM Audio up to
24-bit / 192 kHz
| – Optical S/PDIF Output: Supports Stereo Linear PCM Audio up to
24-bit / 192 kHz and Bitstream formats

Product Usage Instructions

1. Do not dismantle the product housing or modify the printed circuit board module as this may result in electrical shock or burn.
2. Do not attempt to service this product yourself as opening or removing the product housing may expose you to dangerous voltages or other hazards. Refer all servicing to qualified service personnel.
3. Keep this product away from liquids. Spills into the product housing may result in fire, electrical shock, or equipment damage.
4. If liquid spills into the housing, unplug the product immediately. Have the product checked by a qualified service engineer before using it again.
5. Place the product in an even and stable location. If the product falls or is dropped, it may cause an injury and/or malfunction.
6. Avoid exposing the product to extreme temperatures or to high humidity levels as this may result in damage to the product.
7. Only use the supplied External AC Power Adapter. The use of other power adapters may cause this product to fail or may cause a fire.
8. Do not twist or exert excessive force on the ends of the connected cables as this can cause them to malfunction.
9. Take precautions to ensure that all connected cables are not forced to bend beyond their minimum bend radius.

Every effort has been made to ensure that this product is free of defects. DVIGear cannot be held liable for the use of this product or for any direct or indirect consequential damages arising from its use. It is the responsibility of the users of this product to check that it is suitable for their requirements and that it is installed correctly. The terms HDMI, HDMI High- Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. All other third- party trademarks used herein are the properties of their respective owners.

WARNING – Product Safety

1. Do not dismantle the product housing or modify the printed circuit board module as this may result in electrical shock or burn.
2. Do not attempt to service this product yourself as opening or removing the product housing may expose you to dangerous voltages or other hazards. Refer all servicing to qualified service personnel.
3. Keep this product away from liquids. Spills into the product housing may result in fire, electrical shock, or equipment damage. If liquid spills into the housing, unplug the product immediately. Have the product checked by a qualified service engineer before using it again.
4. Place the product in an even and stable location. If the product falls or is dropped, it may cause an injury and/or malfunction.
5. Avoid exposing the product to extreme temperatures or to high humidity levels as this may result in damage to the product.
6. Only use the supplied External AC Power Adapter. The use of other power adapters may cause this product to fail or may cause a fire.
7. Do not twist or exert excessive force on the ends of the connected cables as this can cause them to malfunction. Take precautions to ensure that all connected cables are not forced to bend beyond their minimum bend radius. Product Liability

Every effort has been made to ensure that this product is free of defects. DVIGear cannot be held liable for the use of this product or for any direct or indirect consequential damages arising from its use. It is the responsibility of the users of this product to check that it is suitable for their requirements and that it is installed correctly. DVIGear, Inc. is the owner of numerous trademarks, both registered and unregistered, including without limitation, the following marks: DVIGEAR®, DISPLAYNET®, DISPLAY NOT SERVER®, DISPLAY NOT MANAGER®, N/AV Design®, HYPERLIGHT®, and WILDCAT®. The terms HDMI, HDMI High-Definition Multimedia Interface, and HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. All other third- party trademarks used herein are the properties of their respective owners. 2021 DVIGear, Inc. All rights are reserved. No part of this manual may be reproduced or transmitted by any form or means, electronic or mechanical, including photocopying, recording, or by any information storage or retrieval system, without the prior written consent of DVIGear.

INTRODUCTION

DVIGear’s Wildcat® DVI-7570 is the first in a new generation of value-focused HDMI extenders. They employ visually lossless compression that allows resolutions of 3840 x 2160 /60p (4:4:4) to be extended as far as 30 meters (98 ft.) over a single CAT6A cable. Resolutions up to 3840 x 2160 /30p (4:4:4) can b  extended to 70 meters (230 ft.). This extender includes a buffered HDMI Loop Output for a local HDMI display on the transmitter unit. The receiver unit includes de-embedded Analog and Digital (TOSLINK) audio outputs to facilitate connections to an external audio system. The DVI-7570 supports HDMI 4K /60p, is HDCP 2.2 compliant, and supports bi-directional Power-over-Cable, giving integrators and system designers the flexibility to power the extender set at either end of the signal chain. The extenders occupy a minimal amount of space and can easily be concealed thanks to an ultra-compact metal case, which includes all required mounting hardware for a seamless, low-profile installation. These features, together with the Wildcat Extender’s exceptional performance, make it the ideal solution for cost-sensitive applications that demand high-quality HDMI signal distribution.

Features
The DVI-7570 offers several exceptional features:

• Supports HDMI 4K /60p, HDCP 1.4 and 2.2 compliant
• Supports resolutions up to 3840×2160 /60p (4:4:4) with visually lossless compression
• Extends HDMI and IR over a single CAT6A cable
• Maximum extension distances:
• 3840 x 2160 /60p: 98 ft. (30 m)
• 3840 x 2160 /30p: 230 ft. (70 m)
• Bi-directional Power-over-Cable (POC)
• Buffered HDMI Loop Output on DVI-7570-TX
• Analog and Digital (TOSLINK) De-embedded Audio Output on DVI-7570-RX
• Ultra-compact, low-profile case for easy concealment
• Locking DC power connectors for added security and reliability
• Mounting hardware included

SPECIFICATIONS

Specifications (Continued)

Note 1 : In most cases, HDMI audio is not supported for resolutions between 1920×1080 and 3840×2160. For more information, please contact DVIGear Support.
Note 2: All specifications are subject to change without notice.

Supported Resolutions
This product supports all standard resolutions up to and including 1920×1080, as well as 3840×2160 /60p using visually lossless compression. Resolutions that have a pixel clock rate of above 600 MHz are supported. Due to the compression technology used, Audio is not supported for resolutions of more than 1920×1080 and less than 3840×2160 – unless the pixel clock is less than 150 MHz.

PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make certain the following items are contained in the shipping carton:

• 1x DVI-7570-TX 4K HDMI CAT6 Transmitter
• 1x DVI-7570-RX 4K HDMI CAT6 Receiver
• 1x User Guide
• 1x External AC Power Adapter (+12 VDC)
• 1x IR Transmitter
• 1x IR Receiver
• 4x Mounting Brackets with Screws

Note: Please retain the original packing material in case you need to return the unit. If you find any items missing, contact your reseller or DVIGear immediately. Please have the Model Number, Serial Number, and Invoice Number available for reference when you call.

CONNECTING THE HARDWARE
Please study the images below and become familiar with the signal inputs, outputs, and the location of the power connector.

1. HDMI Output: female connector; connect to an HDMI or DVI display.
2. This is a buffered HDMI Loop Output for a local HDMI display.
3. HDMI Input: female connector; connect to an HDMI or DVI source

Transmitter Unit – Output View

1. CAT Output: RJ-45 female connector. See the warning below.
2. Service Port: reserved for qualified technical personnel.
3. IR OUT: connect IR transmitter to accept IR signal from Rx Unit and output to a source device.
4. 12 VDC Power Input: screw locking female connector for AC Power Adapter

Receiver Unit – Input View

1. CAT Input: RJ-45 female connector. See the warning below.
2. Service Port: reserved for qualified technical personnel.
3. IR IN: connect IR receiver to send IR signal over CAT-X cable to Tx Unit.
4. 12 VDC Power Input: screw locking female connector for AC Power Adapter.
5. Receiver Unit – Output View

HDMI Output: female connector; connect to an HDMI or DVI display.

• 1 1 2 2 3 3
• 1 1 2 2 3 3
• 1 1 2 2 3

SPDIF Output: female TOSLINK connector; connect to an audio receiver. Analog Stereo Line Out: female 3.5mm connector; connect to an audio receiver.
WARNING 1: The CAT cable ports are designed to connect to compatible DVIGear Wildcat® series products only. Do not connect any device to the CAT cable connector unless you are sure it is compatible. Connecting incompatible devices with similar connectors may cause harm to the devices.
WARNING 2: It is typical for the CAT cable receiver unit to operate at higher temperatures than the transmitter unit. In order to ensure proper operation and long-term reliability, care must be taken to ensure airflow is not restricted in any way.

System Set-up

This HDMI extension system consists of a Transmitter unit (DVI-7570-TX) and a receiver unit (DVI-7570-RX). To connect this system, first remove power from all devices (installing devices, while powered, may cause damage). Connect a CAT6A twisted pair cable to the CAT OUT on the transmitter unit. Connect the other end of the CAT6A twisted pair cable to the CAT IN on the receiver unit.
Connect an HDMI or DVI signal source to the HDMI IN port on the transmitter unit. Connect an HDMI or DVI display device (e.g. projector) to the HDMI OUT on the receiver unit.

Additionally, the transmitter includes a buffered HDMI Loop Output for a local HDMI display. Use of a High-Speed HDMI® cable or High-Speed HDMI to DVI-D cable such as DVIGear’s High Resolution (HR™) Series is recommended. Connect an HDMI or DVI display device (e.g. local monitor) to the HDMI OUT on the transmitter unit. The receiver features both a de-embedded Analog and a Digital (TOSLINK) audio output to facilitate connections to an external audio system such as a soundbar or speaker system.

Note: Proper operation of this product depends on the use of high-quality cables. CAT6A S/FTP (550 MHz) 23AWG twisted pair cable is recommended to maximize extension distances. 4.2 Power Connections and Bi-Directional Power over CAT Cable The DVI-7570 is capable of being powered on either the transmitter or receiver side, with the opposite side receiving its power over the CAT cable (POC). This feature eliminates the need for a second external power supply at either the receiver or transmitter. For POC operation, connect the supplied AC Power Adapter to the 12 VDC Power Input on either unit and then to a working AC power source. Once the unit detects the POC-compatible unit on the other side of the connection, it will provide power over the CAT cable. If non-POC operation is desired, simply connect the optional AC Power Adapter to the 12 VDC Power Input on both units. In this case, the units will not supply power to each other.
Note : This product utilizes a locking DC power connector to prevent the power cable from disengaging. Insert the DC plug into the power input jack on the rear panel, then gently rotate the locking collar in the clockwise direction until it is secure. To remove the power connection, simply unscrew the locking collar counter-clockwise and then extract the power cable.

Mounting Hardware
Each transmitter and receiver unit comes with a pair of mounting brackets to facilitate installation on furniture or other surfaces. To affix each bracket to an extender unit, align the two mounting holes of the plate with the holes on the underside of the unit. Next, use the supplied screws to secure the bracket to the case.

OPERATING THE UNIT
Once all connections have been made and power has been applied to all components, this extension system should function immediately. This product has no adjustments and does not require configuration

TROUBLESHOOTING

WARNING 1: The CAT cable ports are designed to connect to compatible DVIGear Wildcat® series products only. Do not connect any device to the CAT cable connector unless you are sure it is compatible. Connecting incompatible devices with similar connectors may cause harm to the devices.
WARNING 2: It is typical for the CAT cable receiver unit to operate at higher temperatures than the transmitter unit. In order to ensure proper operation and long-term reliability, care must be taken to ensure airflow is not restricted in any way. If this unit does not appear to be functioning, make certain that the 12 VDC power adapter is connected securely to a functioning AC power outlet and to one of the units. Ensure that the Link LEDs on both TX and RX units are both lit. If the system fails to display a signal, power of all devices and confirm that the following connections are properly installed: the TX unit must be connected to the source using the shortest possible high-quality cable. The RX unit must be connected to the display using the shortest possible high-quality cable. Ensure that the CAT cable between the TX and RX is of the highest quality possible and within the allowable length noted on page 3. Verify that none of the cables used show signs of damage and are not forced to bend beyond their minimum bend radius.

If the IR connection is not functioning, verify that the IR Transmitter and IR Receivers are connected in the correct configuration according to section 4.1 and that all connectors are securely seated. Once all connections have been verified, power the display device on first and then the signal source. If the system still fails to display an image, check to ensure that the HDMI or DVI signal source is compatible with the display by making a direct connection between the two so as to bypass the extender pair. If there is still no image, then there is a compatibility issue between the source and the display that must be resolved. If there are issues with audio dropouts, ensure that a compatible resolution is being used. Refer to section 2.2 for more details If the problem persists after trying the above suggestions, please contact your dealer for additional assistance. If the dealer’s technical personnel are unable to assist you, please contact DVIGear via telephone at 1.888.463.9927 (toll-free for the United States and Canada) or 1.770.421.6699. You may contact DVIGear by e-mail at support@dvigear.com

LIMITED WARRANTY

LIMITED WARRANTY – Subject to the limitations stated below, DVIGear warrants that this product will be free from defects in materials and workmanship for a period of three (3) years from the date of purchase. Should the product, in DVIGear’s opinion, prove defective within the warranty period stated above, DVIGear, at its option, will repair or replace this product without charge. Any defective parts replaced become the property of DVIGear. This warranty does not apply to products that have been damaged due to an accident, unauthorized alterations, improper repair, modifications, inadequate maintenance, and care or use in any manner for which the product was not intended. If repairs are necessary under this warranty policy, the original purchaser must obtain a Return Authorization Number from DVIGear and return the product freight prepaid to a location designated by DVIGear. After repairs are complete, the product will be returned, and freight prepaid.

The foregoing warranty is the sole and exclusive warranty given by DVIGear, express or implied, and DVIGear disclaims all implied warranties, including but not limited to implied warranties of merchantability or fitness for a particular use. LIMITATIONS – The liability of DVIGear with respect to any defective products will be limited to the repair or replacement of such products. In no event shall
DVIGear be responsible or liable for any damage arising from the use of such defective products, including but not limited to loss of use, revenue or profit, whether such damages are direct, indirect, consequential, or otherwise, and whether such damages are incurred by the reseller, end user, or any third party.

REGULATORY COMPLIANCE
This product is compliant with appropriate FCC, CE, and RoHS rules and regulations. The supplied AC Power Adapter is compliant with CE, UL, C-UL, CEC, DOFT, GS, PSE, CCC, KCC, CB, TUV, RoHS, WEEE, S, RCM, and Class II rules and regulations.

Toll-Free 888.463.9927
Phone +1.770.421.6699
Fax +1.770.234.4207
DVIGear, Inc.
1059 Triad Court, Suite 8
Marietta, Georgia USA 30062

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>