ACROMA 15 x Max 60W Candelabra Base Installation Guide
- June 12, 2024
- ACROMA
Table of Contents
ACROMA 15 x Max 60W Candelabra Base Installation Guide
Safety lnformation
READ AND SAVE THESE INSTRUCTIONS
-
For your protection and safety,carefully read and understand the information provided in this manual completely before attempting to assemble,install,or operate this product.Failure to do so could lead to electrical shock,fire,or other injuries that could be hazardous or even fatal.
-
Before touching any wire,use a voltage tester to make sure it not live.
-
When replacing fuses,turn off the main power firs.Make sure your hands and feet are dry,and place one hand behind your back to prevent electricity from making a complete circuit through your chest.
Touch the plug fuse only by its insulated rim.Remove cartridge fuses with a fuse puller. -
Use tools with insulated handles and ladders made of wood or fiberglass.
-
To protect children,place a safely cover over any unused outlets.
DANGER: Before staring
installation of this fixture or removal of a previous fixture,disconnect the
power by turning off the circuit breaker,removing the fuse at the fuse box,or
tripping the breaker that controls that circuit.Tape a sign to the panel
warning others to leave the circuit alone while you work.
CAUTION: CONSULT A QUALIFIED
ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS. lf you have any non-
electrical questions about this fixture please contact our customer service
via the distributor where you purchased this product from. We will be more
than happy to assist.
TOOLS REQUIRED (NOT INCLUDED)
-
Phillips Screwdriver
-
**Wire Stripper
**
- **Pliers
**
-
Safety Goggles
-
**Electrical Tape
**
HARDWARE INCLUDED
-
Canopy
-
Crossbar assembly
-
Outlet box screw (short) x 2
-
**Green ground screw(on mounting plate)
**
-
Wire connector x 3
-
**Finial x 2
**
-
Support screw(long) x 2
-
Hexn nut x 4
-
Flat washer x 2
-
**Chain end Loop x 2
**
-
Chain x 1
-
**Connector ring x 1 Package 1
**
- **Socket sleeves x 15
**
- Side hanging rod x 2
Assembly lnstructions
Assembly of this fixture will be accomplished by first determining the length of stem or chain required, attaching the mounting plate to the junction box, making all necessary electrical connections, hanging the fixture from the ceiling and then installing the fixture.
Safety Warning
Read wiring and grounding instruction and any additional directions. Turn
power supply off during installation. If new wiring is required, consult a
qualified electrician or local authorities for code requirements
Installation
STEP 1
STEP 2
STEP 3
STEP 4
Connect the lanyard to the mountingbracket to help hold the fixture inplace
while making the wire connections.
STEP 5
STEP 6
Warranty
ONE (1) YEAR WARRANTY
WHAT IS COVERED
The manufacturer warrants this fixture to be free from defects in
materialsand workmanship for a period of one (1) year from date of
purchase.The warranty applies only to the original consumer purchaser and only
toproducts used in normal use and service.
If this product is found to be defective,the manufacturer’s only
obligation,andyour exclusive remedy,is the repair or replacement of the
product at themanufacturer’s discretion,provided that the product has not been
damagedthrough misuse,abuse,accident,modifications,alteration,way not in
accordancewith the instructions supplied with the product.This warranty shall
not apply toa failure of the product as a result of an
accident,misuse,abuse,negligence,alteration,faulty installation,or any other
failure not relating to faulty materialor workmanship.
This warranty shall not apply to the finish on any portion of the
product,suchas surface and/or weathering,as this is considered normal wear and
tear.
WHAT IS NOT COVERED
The manufacturer does not warrant and specifically disclaims any
warranty,whether expressed or implied, of fitness for a particular purpose,
other thanthe warranty contained herein. The manufacturer specifically
disclaims anyliability and shall not be liable for any consequential or
incidental loss ordamage, including but not limited to any labor/expense costs
involved in thereplacement or repair of said product.
