Florevita KR-S089 HydraPro Straightener User Manual

HYDRAPRO STRAIGHTENER
MANUAL
KR-S089

KR-S089 HydraPro Straightener

Keep this manual for future reference
READ AND SAVE IMPORTANT SAFETY INSTRUCTIONS

Read the following safety instructions carefully before using

WARNING – THIS APPLIANCE MUST NOT BE TAKEN INTO A BATHROOM, IT SHOULD NOT BE USED NEAR BATHTUBS, SHOWERS, BASINS OR OTHER VESSELS  CONTAINING WATER OR OTHER LIQUIDS.
This product is not suitable for use in bath or shower.
THE STYLER SHOULD BE UNPLUGGED FROM MAINS SUPPLY WHEN NOT IN USE.

CAUTION:

• Do not leave the styler unattended when switched on.
• Allow the styler to cool down before storage it.
• Do not immerse in water or other liquids.
• Do not place styler on soft material e.g. carpet, bedding, towels, rugs etc.
• Always ensure the voltage to be used corresponds to the voltage sated on the unit.
• Keep this product out of reach of children.
• Avoid allowing any part of the hot plates to contact the face, neck or scalp.
• Do not wrap the cord around the unit. Check cord regularly for any sign of damage.
• Damaged cords can be dangerous. If the supply cord of this unit becomes damaged, discontinue use immediately, contact us for repair or replacement in order to avoid a hazard. Special tools are required for repair. Unqualified repair work could lead to hazardous conditions for the user. Do not try to repair the product yourself.
• We do not accept responsibility for damage to the product, persons or other items(s), caused by misuse, abuse or non-compliance with these instructions.
• Do not use any liquid or water other than pure water in this product to avoid damage to the device. Purified water is recommended

HOW TO FILL THE WATER TANK

• Step 1:
  Ensure the power is off. Do not attempt to fill the tank while the Styler is on and or hot.
  • Step 2:
  Open the water tank cover, See FIG 1.

• Step 3:
  Use the water bottle FIG 2 for filling the water tank

• Fill the think water tank with purified water as shown in FIG 2.
  Tip: When filling the water tank, please tilt the water tank by 45° to avoid the water in the water tank overflowing during the filling process.

• Step 4:
  Cap the water tank cover, See FIG 3.
  

• Step 5:
  

  • Plug in the appliance and turn ON.
  • Adjust the temperature
  • Turn on the steam button
  • Styling after the appliance reached the temperature.

Tips:

• Please note that steam will be generated at temperatures above 100°C / 212°F. The hair straightener (in the clipped state) will automatically generate steam every five seconds.
• After the device is turned on, the system will automatically start the self-test. If the hair straightener generates a slight vibration after the device is turned on, the system starts to detect it, which is normal.
• When the water tank is empty, turn on the steam switch, and the hair straightener will emit a prompt sound of no water. Please turn off the hair straightener when filling water

INSTRUCTIONS BEFORE USE

1. Before use , make sure hair is clean and tangle -free.
2. Fill the tank to your desired level with water.
3. Plug in the device and press and hold the on-off switch
4. When the appliance reaches the desired temperature, the unit will beep when it’s ready to use.
5. Run the straightener through the entire length of the hair, without stopping.
6. Repeat only twice per section to prevent hair damage.
7. The hair straightener (in the locked state) will automatically generate steam every five seconds.
8. The system will automatically start self-test after the device is turned on. If the hair straightener generates a slight vibration after the device is turned on, the system starts to  detect it. This is normal.
9. When the water tank is empty, turn on the steam switch, and the hair straightener will emit a prompt sound of no water. Please turn off the hair straightener when filling water.

STRAIGHTENING YOUR HAIR

1. Prep your hair. Make sure your hair is clean & tangle -free.
2. Depending on your hair type and hair length – this information below is aimed at Medium hair type and shoulder length hair. Take a 5 cm wide x 1 cm thick section of hair. Move the Styler over the sectioned hair starting at the roots about 1 cm away from the scalp, run the Styler slowly through to the ends of the Hair with light pressure.
3. Repeat this process, section by section until your hair is completely straightened, soft and smooth.

CURLING YOUR HAIR

The steam hair straightener with its rounded edge plates enables you to also create Curls, waves, and lots of other hair styles.

1. Prep your hair. Make sure your hair is clean & tangle -free. Use the included heat-resistant glove to prevent burns.

2. Take a small section of hair, and insert it into your Styler. Your sections can vary in size for a more natural, beautifully imperfect look – this up to you . You may also decide here you would like your curl to start and can place your Styler accordingly.

3. Twist your wrist, (the one holding the Styler), about a half-turn, then pull ,then twist again ,then pull.
   Keep repeating this until you reach the end of your hair. For a more beach feel, keep the very ends of your hair out of the styler.

4. (ALTERNATIVE): Twist and pull just as Step 3 indicated, but for a tighter, more curly curl, twist the mid-shaft to ends around the entire iron mimicking what you would do with a curling iron.

Tip: you may want to change the direction of your curls near your face based on personal preference.

TEMPERATURE SETTING BASED ON HAIR TYPE
Low 150°C = 300°F
Fragile, very fine textured hair
Medium 190°C = 375°F
Normal, medium textured hair
High 230°C = 450°F
Thick resistance, coarse textured hair

CLEANING AND MAINTENANCE

Ensure the unit is unplugged and cool. To maintain the effectiveness of your product wipe clean after use with a damp cloth. Do not use an abrasive cleaning fluid to clean, as damage will occur.

WARRANTY

If you found the Tank have a little water that is normal, because our product is 100% tested with water as part of our quality control procedure.
The following warranty conditions are based on the European Directive 99/44/EC and the Civil Code. For this product, we grant a guarantee according to the following conditions:

• Florevita warrants that any defects due to faulty materials and workmanship in its products will be repaired at Florevita’s expense for a period of two years from the date of purchase, or that the product will be replaced in its entirety. This warranty covers the cost of materials and labour.
• Repairs will not be carried out at Florevita’s expense if it is not convincingly demonstrated (by means of a sales receipt or electronic invoice) that the day of the claim is within the warranty period.
• The warranty does not apply to product parts and products (and/or product parts) that are subject to wear and tear or that can be considered as consumables due to their nature, as well as to glass parts.
• The warranty is void if the defect is caused by damage resulting from improper use, lack of maintenance (such as scaling of parts) or if the product has been altered or repairs have been carried out by persons not authorized by Florevita.
• To use the appliance correctly, the instructions in the user manual must be followed

TECHNICAL PARAMETERS

| Product Name:
HYDRAPRO STRAIGHTENER| Florevita, Fonteinstraat 2
9890 Gavere, Belgium
www.florevita.com
---|---|---
Model:
KR-S089| Serial Number:
ST-202208| Made in China
|
Voltage: 100-240V,50-60Hz
Power: 75W
Material: PET,PC,PA, ceramic coating
plates, MCH heater| Gross Weight, kg: 0.5kg
Net Weight, kg: 0.5kg
Product Size: 30°3.4°3.845cm
Packaging Size: 37°11.65°7.65cm

Florevita
Fonteinstraat 2, 9890
Semmerzake, Belgium
info@florevita.com
Florevita.com

Manufacturer
Dongguan KangRoad Electrical
Technology Co.,Ltd
Jinchuan No.2 Rd, Jinchuan industrial Area, Xiegang
Town, Dongguan
City, Guangdong Province, China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>