frient IO Module Smart Zigbee Input Output Instruction Manual
- June 13, 2024
- Frient
Table of Contents
IO Module INSTALLATION MANUAL
Version 1.0
Product description
With the IO Module, you can connect wired devices to a Zigbee network. Providing four inputs and two outputs, the IO Module works as a bridge between wired devices and a control system over Zigbee networks.
Disclaimers
CAUTION:
- Choking hazard! Keep away from children. Contains small parts.
- Please follow the guidelines thoroughly. The IO Module is a preventive, informing device, not a guarantee or insurance that sufficient warning or protection will be provided, or that no property damage, theft, injury, or any similar situation will take place. frient cannot be held responsible in case any of the above-mentioned situations occur.
Precautions
WARNING: For safety reasons, always disconnect power from the IO module, before connecting wires to inputs and outputs.
- Do not remove the product label as it contains important information.
- Do not open the IO Module.
- Do not paint the device.
Placement
Connect the IO Module to a device that is located at a temperature between
0-50°C.
Connecting to wired device You can connect the IO Module to different wired
devices: doorbells, window blinds, wired security devices, heat pumps and
more. The connection of the different devices follows the same principle,
using the different inputs and outputs:
IN1|
---|---
IN2| Inputs with internal Pull Up. Must be
IN3| shorted to IO Module GND for signal
IN4| IO Module GND
NC2| Normally Closed for Relay Output 2
COM2| Common for Relay Output 2
NO2| Normally Open for Relay Output 2
NC1| Normally Closed for Relay Output 1
COM1| Common for Relay Output 1
NO1| Normally Open for Relay Output 1
5-28 V| Power Supply
d.c.| NOTE: Use ”5-28 V” or ”USB PWR”. Use ”5-28 V” or ”USB PWR”. If both are
connected ”5-28V” is the primary Power Supply.
USB| Power Supply
PWR| NOTE: USB PWR is then used
USB PWR is then used as fall back in case ”5-28 V” is disconnected.
RST| Reset
LED| User Feedback
Getting started
- When the device is connected and powered up, the IO Module will start searching (up to 15 minutes) for a Zigbee network to join. While the IO Module is searching for a Zigbee network to join, the yellow LED flashes.
- Make sure that the Zigbee network is open for joining devices and will accept the IO Module.
- When the LED stops flashing, the device has successfully joined the Zigbee network.
- If the scanning has timed out, a short press on the reset button will restart it.
Resetting
Resetting is needed if you want to connect your IO Module to another gateway
or if you need to perform a factory reset to avoid abnormal behavior.
STEPS FOR RESETTING
-
Connect the IO Module to a power outlet.
-
Press and hold the reset button with a pen (see Illustration b).
-
While you are holding the button down, the yellow LED first flashes once, then two times in a row, and finally numerous times in a row.
c.
-
Release the button while the LED is flashing numerous times in a row.
-
After you release the button, the LED shows one long flash, and the reset is completed.
Modes
SEARCHING GATEWAY MODE
The yellow LED flashes.
Fault finding
- In case of a bad or weak wireless signal, change the location of the IO Module. Otherwise, you can relocate your gateway or strengthen the signal with a range extender.
- If the search for a gateway has timed out, a short press on the button will restart it.
Disposal
Dispose the product properly at the end of its live. This is electronic waste
which should be ecycled.
FCC statement
Changes or modifications to the equipment not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
ISED statement
Innovation, Science and Economic Development Canada ICES-003 Compliance Label:
CAN ICES-3 (B)/NMB-3(B).
CE certification
The CE mark affixed to this product confirms its compliance with the European Directives which apply to the product and, in particular, itscompliance with the harmonized standards and specifications.
IN ACCORDANCE WITH THE DIRECTIVES
-
2014/53/EU
-
RoHS Directive 2015/863/EU amending
2011/65/EU -
REACH 1907/2006/EU + 2016/1688
Other certifications
Zigbee 3.0 certified
All rights reserved.
frient assumes no responsibility for any errors, which may appear in this
manual. Furthermore, frient reserves the right to alter the hardware,
software, and/or specifications detailed herein at any time without notice,
and frient does not make any commitment to update the information contained
herein. All the trademarks listed herein are owned by their respective owners.
Distributed by frient A/S
Tangen 6
8200 Aarhus
Denmark
Copyright © frient A/S
Documents / Resources
|
frient IO Module Smart Zigbee Input
Output
[pdf] Instruction Manual
IO Module Smart Zigbee Input Output, IO Module, Smart Zigbee Input Output,
Zigbee Input Output, Input Output, Output
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>