KitchenAid MK2167 Microwave Trim Kit Instruction Manual
- June 13, 2024
- KitchenAid
Table of Contents
KitchenAid MK2167 Microwave Trim Kit
Product Information
- The Microwave Oven Built-In Trim Kit is designed for use with built-in ovens and provides a seamless and stylish integration of the microwave oven into your kitchen cabinetry. It is compatible with models MK2167 and MK2160.
- This trim kit is UL listed for use over any electric or gas built-in oven that is up to 30 inches (76.2 cm) wide, ensuring safety and compatibility.
- The kit includes rails, a bottom duct, and a trim kit frame. It also comes with short screws and long wood screws for installation.
Product Usage Instructions
- Before starting the installation, gather the following tools: measuring tape, pencil, Phillips screwdriver, drill, and a 7/64 drill bit.
- Refer to the required cutout dimensions provided in the manual. Measure and mark the appropriate dimensions on your cabinetry using a measuring tape and pencil.
- Using a drill and the specified drill bit, create the necessary holes for installation.
- Attach the rails, bottom duct, and trim kit frame according to the provided instructions. Use the included screws for secure installation.
- Ensure that there is a minimum distance of 3 inches (7.6 cm) between the top of the lower oven cutout and the microwave oven cutout floor if installed over a built-in oven.
- If installing the microwave oven in a cabinet without a built-in oven below, maintain a minimum distance of 36 inches (91.4 cm) from the floor to the cutout floor for optimal usability.
- Allow sufficient clearance for the surrounding cabinetry to open and close freely. Maintain at least 1/4 inch (4.0 cm) clearance below the cutout floor (3 inches [7.6 cm] for installation above a built-in oven) and at least 2 inches (5.1 cm) clearance above the cutout opening.
- Ensure the receptacle location meets the minimum depth requirements based on the provided chart and illustrations.
- For electrical safety, plug the microwave oven into a grounded 3-prong outlet. Do not remove the ground prong, use an adapter, or use an extension cord.
Following these instructions will ensure a safe and proper installation of your Microwave Oven Built-In Trim Kit.
Built-In Trim Kit Models MK2167, MK2160
UL listed for use over any electric or gas built-in oven, up to 30″ (76.2 cm)
wide.
MICROWAVE OVEN SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your
appliance. Always read and obey all safety messages.
- This is the safety alert symbol.
- This symbol alerts you to potential hazards that can kill or hurt you and others.
- All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
- DANGER You can be killed or seriously injured if you don’t immediately follow instructions.
- WARNING You can be killed or seriously injured if you don’t follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
INSTALLATION INSTRUCTIONS
Tools and Parts
Tools Needed
Gather the required tools and parts before starting installation. Read and
follow the instructions provided with any tools listed here
- Measuring tape
- Pencil
- Phillips screwdriver
- Drill
- 7/64″ drill bit
Parts Supplied (not shown to scale
Location Requirements
- The microwave oven may be installed over a built-in oven. If installing over a built-in oven, make sure there is a minimum of 3″ (7.6 cm) between the top of the lower oven cutout and the microwave oven cutout floor.
- The microwave oven may also be installed in a cabinet by itself (without a built-in oven below). For best usability, we recommend a minimum distance of 36″ (91.4 cm) from the floor to the cutout floor.
- Make sure the surrounding cabinetry has clearance to open and close freely. Allow a clearance of at least 1⁹⁄₁₆” (4.0 cm) below the cutout floor (3″ [7.6 cm] for installation above a built-in oven), and a clearance of at least 2″ (5.1 cm) above the cutout opening.
- A. Upper cabinet
- B. Microwave oven cutout
- C. Lower oven cutout
- D. Lower cabinets
- E. Floor
Required Cutout Dimensions
For minimum depth requirements, see the chart.
- A. Trim kit frame overhang
- B.Cutout for lower oven
- C. Recommended region for receptacle location (no less than 6″ [15.2 cm] to the right of cutout centerline)
- D.Cutout centerline
Receptacle Location/Minimum Depth
- Within recommended region
- 18″ (45.7 cm) with flush receptacle;
- 21″ (53.2 cm) with non-flush receptacle
- Outside recommended region
- 19¹⁄₂” (49.5 cm) with flush receptacle;
- 22¹⁄₂” (57.2 cm) with non-flush receptacle
NOTES:
- Depth requirements depend upon receptacle and its location within or outside of recommended region. See illustration and chart above.
- Height dimension is critical: 17″ (43.2 cm) minimum, 17¹⁄₈” (43.5 cm) maximum.
- Width measurement has ±1/16″ (2 mm) tolerance.
- 3″ (7.6 cm) minimum dimension is from lower oven cutout ceiling to microwave oven cutout floor.
- Trim kit frame extends 1¹⁄₁₆” (2.7 cm) above and below the cutout opening.
Trim Kit Frame Dimensions
- 27″ (68.6 cm) trim kit
- 30″ (76.2 cm) trim kit
Electrical Requirements
WARNING
Electrical Shock Hazard
- Plug into a grounded 3 prong outlet.
- Do not remove ground prong.
- Do not use an adapter.
- Do not use an extension cord.
- Failure to follow these instructions can result in death, fire, or electrical shock.
Observe all governing codes and ordinances.
Required:
- A 120 volt, 60 Hz, AC only, 15- or 20-amp electrical supply with a fuse or circuit breaker.
Recommended:
- A time-delay fuse or time-delay circuit breaker.
- A separate circuit serving only this microwave oven.
GROUNDING INSTRUCTIONS
For all cord-connected appliances:
The microwave oven must be grounded. In the event of an electrical short
circuit, grounding reduces the risk of electric shock by providing an escape
wire for the electric current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug must be plugged into
an outlet that is properly installed and grounded.
WARNING:
Improper use of the grounding plug can result in a risk of electric shock.
Consult a qualified electrician or serviceman if the grounding instructions
are not completely understood, or if doubt exists as to whether the microwave
oven is properly grounded.
Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the microwave oven.
SAVE THESE INSTRUCTIONS
Prepare Microwave Oven
- Unplug microwave oven before proceeding with installation.
- Remove any loose items inside microwave oven.
- Gently turn microwave oven onto its top, with the door facing forward (toward installer).
- Align the two rails on the microwave oven bottom, as shown, making sure the flanges are forward and pointing up.
- A. Rails (2)
- B. Microwave oven bottom
- C. Short screws (4)
- D. Flanges
- E. Door
- Secure the rails to the microwave oven bottom using four short screws.
Prepare Cutout/Cabinet Opening
- On the cutout floor, find and mark the centerline.
- Place the bottom duct in the opening, with the flange resting against the bottom front facing of the opening.
- A. Cutout floor
- B. Centerline
- C. Bottom duct
- D. Bottom duct flange
- E. Front facing
- Align the center arrows on the bottom duct with the centerline drawn in Step 1 above.
- A. Bottom duct
- B. Center arrows, aligned with centerline
- Mark the three mounting holes through the bottom duct onto the cutout floor.
- A. Short screws (3)
- B. Bottom duct mounting holes
- Using 7/64″ drill, drill pilot holes into the three holes marked in Step 4.
- Realign and install the bottom duct with three short screws.
- Using 7/64″ drill, drill pilot holes through the four mounting holes of the bottom duct flange into the bottom front facing of the cutout/cabinet opening.
Install the Microwave Oven
-
Gently return the microwave oven to its upright position.
-
Position the microwave oven near the cutout opening.
WARNING
Electrical Shock Hazard
- Plug into a grounded 3 prong outlet.
- Do not remove ground prong.
- Do not use an adapter.
- Do not use an extension cord.
- Failure to follow these instructions can result in death, fire, or electrical shock.
-
Plug in microwave oven.
-
Align the rails with the rail guides on the bottom duct.
- A. Rail guides
- B. Rails
-
Slide the microwave oven back and into place. The mounting holes of the rail flanges and bottom duct flange will align against the bottom front facing of the cutout/cabinet opening.
-
Secure the microwave oven to the cutout/cabinet by installing four short screws into the mounting holes.
- A. Mounting holes
- B. Short screws (4)
Install Trim Kit Frame
-
Position trim kit frame over the opening so that the lower tabs rest on the cutout floor, as shown.
- A. Front of trim kit frame
- B. Tabs (upper and lower)
- C. Cutout/cabinet floor
-
Holding the trim kit frame in place, use 7/64″ drill to drill four pilot holes into the front facing of the cutout/cabinet through the mounting hole guides in the upper and lower corners of the trim kit frame.
NOTES:- The holes will be drilled downward from the top, and upward from the bottom at an angle of about 45°.
- To avoid damage to the trim kit frame, do not overtighten screws.
- A. Trim kit frame
- B. Mounting hole guide
- C. Long wood screw (4 – painted)
- D. Cutout ceiling
-
Secure trim kit frame to cutout/cabinet by installing four long wood screws (painted) into the pilot holes drilled in Step 2 above.
Installation is now complete. Replace any loose items that have been removed from microwave oven cavity. Save these Installation Instructions for future reference.
© 2012 Whirlpool Corporation.
All rights reserved. Used under license in Canada.
Printed in China.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>