SIEMENS SN23EI00ME Dishwasher User Guide

SIEMENS SN23EI00ME Dishwasher

Product Information

The product is a dishwasher equipped with Home Connect technology, allowing users to control and change settings using a mobile device through the Home Connect app. The dishwasher has various features such as water hardness settings, a dispenser for special salt and rinse aid, and different programmes for washing tableware. The appliance also has filters that need to be cleaned regularly.

Setting up Home Connect

Tip: Connect your appliance to a mobile device. You can conveniently change all settings using the Home Connect app.

1. Install the Home Connect app on your mobile device and follow the instructions.
2. Scan the QR code with the Home Connect app.

Overview of water hardness settings

You can find an overview of the water hardness values that can be selected here. A table of country-specific units can be found in the instruction manual.The dishwasher offers different water hardness settings based on the user’s preference or region. Refer to the table below for the available settings:

Setting the water softening system

1. Press .
2. To open the basic settings, press Setup 3 sec. for 3 seconds.
   • The display shows Hxx.
   • The display shows set.
3. Press Start repeatedly until the right water hardness has been set.
4. To save the settings, press Setup 3 sec. for 3 seconds.

Adding Special Salt

1. Unscrew the lid of the dispenser for special salt and remove it.
2. On initial start-up, fill the dispenser with water.
3. Add the special salt to the dispenser. Do not add detergent.
4. Place the lid back on the dispenser and turn to close.

Adding Rinse Aid

1. Press the catch on the lid of the dispenser for rinse aid and lift it.
2. Add rinse aid up to the maximum mark.
3. Close the lid of the dispenser for rinse aid until it clicks into position.

Adding detergent

1. Add the detergent to the dry detergent dispenser.
2. Close the lid of the detergent dispenser.
   • a The lid clicks into position

Programs

The programme data has been measured in the laboratory according to European standard EN 60436.
The consumption figures depend on the programme and additional function selected.

The runtime will change if the rinse aid system is switched off or rinse aid needs to be added. The dishwasher offers different programmes for washing tableware. The duration, energy consumption, and water consumption may vary depending on the selected programme and additional functions. Refer to the table below for programme details:

Using the Appliance

1. Load the tableware, ensuring it is suitable for dishwashers and removing large food remnants.
2. Add detergent to the dry detergent dispenser.
3. Switch on the appliance.
4. Select the desired program.
5. Start the program.
6. Remove the tableware at the end of the program.
7. To cancel the programme, press and hold the cancel button for approximately 4 seconds. The programme will be cancelled after about 1 minute.

Cleaning Filters

1. After each wash, check the filters for residue.
2. Turn the coarse filter anticlockwise and remove the filter system.
3. Pull down the micro filter to remove it.
4. Press the locking catches 1 together and lift the coarse filter out ⁠2.
5. Clean the filter elements under running water.
6. Re-assemble the filter system.
7. Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match up.

Cleaning spray arms

1. Unscrew the upper spray arm 1 and pull down to remove 2.
2. Pull up the lower spray arm to remove.
3. Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.
4. Insert the lower spray arm.
   • The spray arm clicks into position.
5. Insert the upper spray arm and screw it firmly in place.

Clean wastewater pump

1. Disconnect the appliance from the power supply.
2. Remove the filter system.
3. Scoop out any water.
4. Prise off the pump cover using a spoon and grip it by the crosspiece.
5. Lift the pump cover inwards at an angle and remove it.
6. Remove any remnants of food and foreign bodies in the area of the impeller.
7. Insert the pump cover 1 and press down 2⁠.
   • The pump cover clicks into position.
8. Install the filter system.

Troubleshooting

The filters in the water connection of the supply or AquaStop hose are blocked.

1. Switch off the appliance.
2. Pull out the mains plug.
3. Turn off the water tap.
4. Unscrew the water connection.
5. Remove the filter from the supply hose
6. Clean the filter.
7. Re-insert the filter in the supply hose.
8. Screw the water connection back on.
9. Check the water connection for leaks.
10. Restore the power supply.
11. Switch the appliance on.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>