aerofabb VW-MK7-GTI-V1-FWS-SE V2 Street Edition Front Splitter Instruction Manual

June 13, 2024
aerofabb

aerofabb VW-MK7-GTI-V1-FWS-SE V2 Street Edition Front Splitter Instruction Manual
aerofabb VW-MK7-GTI-V1-FWS-SE V2 Street Edition Front
Splitter

We provide Fasteners in Stainless Steel to ensure a long life span. Although Stainless Steel has many benefits like extreme corrosion resistance, threads can be sensitive to Nylon Lock Nuts. We recommend installing hardware with an Anti-Seize thread lubricant to prevent thread galling. Slowing down speed of install and keeping bolts stationary while tightening nuts are common practices to prevent thread galling.

INSTALLATION GUIDE

INSTALLATION GUIDE

NOTES:

  1. IGNORE SUPPORT ROD HOLES (E) IF YOU PURCHASED A V2.
  2. Labeled Hardware corresponds to labeled holes shown in diagram.

ALIGNMENT HARDWARE (A)

QTY DESCRIPTION
2 M6 X 30MM BOLT
2 M6 X 18MM OD WASHER
2 ?” OD X ‘/‹” LG SPACER
2 M6 X 12MM OD WASHER
2 M6 NYLON LOCKNUT

HARDWARE (B)

QTY DESCRIPTION
8 M6 X SOMM BOLT
24 FENDER WASHER
8 ?” OD X ‘/‹” LG SPACER
8 */‹” OD X ’/»” LG SPACER
8 M6 NYLON LOCKNUT

HARDWARE (C)

QTY DESCRIPTION
2 M6 X 30MM BOLT
2 FENDER WASHER
2 M6 X 18MM OD WASHER
2 M6 NYLON LOCKNUT

HARDWARE (D)

QTY DESCRIPTION
4 M6 X 30MM BOLT
8 FENDER WASHER
4 M6 NYLON LOCKNUT

NOTES:

CONFIRM NO HARDWARE IS MISSING BEFORE INSTALL.

MAKE THE FOLLOWING TOOLS READY FOR USE

  • Drill
  • 1/4” Drill Bit
  • 10mm Wrench
  • 4mm Hex Wrench
  • T-25 Torx
  • Anti-Seize (recommended)

aerofabb, LLC is not responsible for damage to you or your vehicle while following this Install Guide and/or installing aerofabb products. Professional install is recomended. aerofabb also recommends installing hardware with Anti- Seize (thread lubricant) and Hand Tools to prevent thread galling.

  1. Using a T-25 Torx, remove Front Bumper and place upside down on a non-abrasive surface.

  2. ldentify pre-existing holes (A) on underside of Front Bumper (closest to wheels).

  3.  Using a 1/4” Drrill Bit, drill directly through pre-existing Bumper holes (A) widening them to 1/4”.

  4. Place the aerofabb Front Splitter on underside of Bumper. Using a 4mm Hex and 10mm Wrench, install ALIGNMENT HARDWARE (A) passing through both Splitter and Bumper holes (A). Tighten Hardware.
    Installations

  5. With ALIGNMENT HARDWARE (A) installed and Splitter secured on both ends, drill through the 14 remaining Splitter holes (B), (C), and (D).
    NOTES:

  6. Run Bit through multiple passes to ensure holes are clear of debris.

  7. Check bolt threads for plastic debris before threading locknuts.

  8. Do not overtighten Hardware.

  9. Pull only the following fasteners from HARDWARE (B) and set aside the remaining for later use in Step 11.
    QTY| DESCRIPTION
    ---|---
    8| M6 X SOMM BOLT
    8| FENDER WASHER
    8| °/‹” OD X 5/«” LG SPACER
    8| M6 NYLON LOCKNUT

  10. Use above quantity to Install HARDWARE (B) through Splitter holes (B). Only tighten locknut by hand.
    Installations

  11. Install HARDWARE (C) through Splitter holes (C) and tighten.
    Installations

  12. Install HARDWARE (D) through remaining Splitter holes (D) and tighten.
    Installations

  13. Turn the Bumper right-side up and remove all locknuts from holes (B).

  14. Install the aerobrace™ with remaining fasteners from HARDWARE (B) and tighten.
    Installations
    NOTES:

  15. In Step 11 turn Bumper back upside down to tighten HARDWARE (B).
    – Desaturated Hardware in diagram indicates previously installed.

  16. Check bolt threads for plastic debris before threading locknuts.

  17. Do not overtighten Hardware.
    Installations

  18. Inspect all Hardware for tightness to complete Front Splitter installation.

If you purchased a V1 Street Edition Front Splitter, please refer to the Support Rod Installation Guide to complete your installation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals