Honeywell RDWL311A2000 Portable Wireless Doorbell Installation Guide

June 13, 2024
Honeywell

Honeywell RDWL311A2000 Portable Wireless Doorbell Installation Guide

Installation and Operation Guide
Portable Wireless Doorbell

RDWL311A2000
Read before installing

Preparation

In the box you will find

To install you will need

The push button supplied with this kit is pre-programmed to operate with the doorbell.
If it is not, see “Connect a Push Button” on page 4.

Overview

Just follow these simple steps:

  1. Install batteries.
  2. Set up the doorbell and your preferences.
  3. Install the doorbell and the push button.

Safety

Before proceeding with the installation, please note the following safety warnings:

  • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc.
  • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt.

Install Batteries

  1. Open the battery cover and install 4 AA alkaline batteries.
  2. Open the battery cover and install the CR2032 battery.

Setup and Operation

Press the push button to test whether it is paired with the doorbell. The doorbell will ring. If it does not, see “Connect a Push Button” on page 4.

Change the Tune

Press the Music button to change the doorbell tune.

Every time you press the Music button, the tune will change. Stop pressing the Music button when you hear the tune you want:

Ding Dong
Westminster
Soft Alert
Smart Sax

Installation

Choose a location that is not near a heat source or on something that moves (like a door). For non-mounting locations, choose a place where the doorbell will be easy to hear.

Install Doorbell

If you are not mounting the doorbell to the wall, place it where you want it.

  1. Mount the screw on to the wall using the supplied anchor if necessary. Leave 2 mm of the screw sticking out from the wall.
    Drill 1/4 inch (6.3 mm) holes for the anchor.

  2. Hang the doorbell on the screw.

Install Push Button

  1. Mount the push button bracket in the desired location.
    Use the screws
    –OR–
    Use the adhesive backing. If using the adhesive backing, clean the surface first.

  2. Snap the push button onto the mounting bracket.

Note: If you need to remove the push button, use a small screwdriver to release the tab.

Accessories

You can connect 2 accessories to your doorbell, including other push buttons, window or door opening sensors, and motion sensors.

If you try to connect more accessories than the max number, the LED on the side blinks red.

Connect a Motion Sensor

  1. Press and hold the Setting button on the doorbell for three seconds.
    The LED on the side turns on with an amber color.

  2. Within 20 seconds of pressing the Setting button, wave or make some other kind of motion in front of the motion sensor.

Connect a Push Button

Follow these steps to change the ring for an existing doorbell, too.

  1. Press and hold the Setting button on the doorbell for three seconds.
    The LED on the side turns on with an amber color.

  2. Press the push button.

  3. Within 12 seconds of pressing the push button, press the Music button to select the ring for that push button.

Secret Knock

You can set up a Secret Knock that makes a different ring for each push button. The Secret Knock is triggered by pressing the push button quickly 3 times.

  1. Press the push button 3 times quickly.
  2. Within 12 seconds of pressing the push button, press the Music button to select the ring for the Secret Knock.

Maintenance

Your doorbell and push button require no maintenance except to periodically change the batteries.

If using the correct batteries, battery life should be approximately:

  • Up to 2 years for the doorbell; replace with 4 AA alkaline batteries
  • Up to 2 years for the push button; replace with a CR2032 lithium battery

Low Battery Notification

When the doorbell batteries are low, the LED on the side turns on.

When the push button batteries are low, two beep sounds are heard after the normal tune.

Reset

This process removes all pairings, including the push button that came with this doorbell:

  1. Remove the doorbell battery.
  2. Press and hold the Setting button, and replace the battery at the same time.
  3. The doorbell will beep several times rapidly, and is returned to its factory default settings.

Specifications

Troubleshooting

For help please visit resideo.com or call 1-800-633-3991.

CAUTION: Before operating, make sure that the product components have not been damaged, have not been exposed to water or high temperatures.

FCC Regulations

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 millimeters between the radiator and your body.

IC Regulations

CAN ICES-3(B)/ NMB-3(B)

This device complies with Industry Canada licence‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3(B)/NMB-3(B)

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 millimeters between the radiator and your body.

The operation of this equipment is subject to the following two conditions: (1) this equipment or device may not cause harmful interference, and (2) this equipment or device must accept any interference, including interference that may cause undesired operation.

Resideo Technologies, Inc.
1985 Douglas Drive North, Golden Valley, MN 55422
1-800-468-1502
33-00185EFS—07 M.S. Rev. 03-20 | Printed in United States

© 2020 Resideo Technologies, Inc. All rights reserved.
The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Honeywell User Manuals

Related Manuals