TENIA RDNA042C Remote Device Instructions
- June 13, 2024
- TENIA
Table of Contents
- TENIA RDNA042C Remote Device Instructions
- WARNINGSAND CAUTIONS
- RF EXPOSURE STATEMENT
- IC Information
- Remote Control
- FCC CAUTION
- Remote Control
- Battery model: CR2032
- Status Indicator
- ⑪ Dimming Button (UP)
- Dimming Button (Down)
- Accessory Information
- Tools Needed To Install
- 4.Installation
- .1.2 Installing the panel
- Mode two:
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
TENIA RDNA042C Remote Device Instructions
Model No. | RDNA042C |
---|---|
Rated Voltage | 3VDC |
WARNINGSAND CAUTIONS
-
Chemical Burn Hazard. Keep batteries away from children. 2.This product contains a lithium button/coin cell battery. If
a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. -
The cells shall be disposed of properly, including keeping them away from children.
-
Even used cells may cause
RF EXPOSURE STATEMENT
This equipment complies with the FCCRFradiationexposurelimits set forth for
anuncontrolled environment.
This equipment meets the exemption from the routine evaluation limits in
section 2.5 of RSS-102.
Cet équipement est conforme à l’exemption des limites d’évaluation habituelle
de la section 2.5 de la norme RSS-102.
IC Information
This device contains licence-exempt transmitter(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:(1) This device may not
cause interference.and (2) This device must accept any interference, including
interference that may causeundesiredoperationof thedevice.
L’émetteur/récepteur exempt delicencecontenudans leprésent
Remote Control
Status Indicator
Power Button
Accessory Information
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving
- Increase the separation between the equipment and
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
- Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION
Any changes or modifications to this unit not expressly approved by the manufacture could void the user’s authority to operate the equipment.
Remote Control
Note:
- The battery of the remote control can be
Battery model: CR2032
Status Indicator
1 Indicator lights white: Press any button once.
Power Button
- Turn on: Short press once when in
- Turn off: Short press once when in
- Pairing mode of remote control: When the dimmer enters the pairing mode, press the power button (remote control) once within After the pairing is successful, the
status indicator stops blinking.
⑪ Dimming Button (UP)
- Short press the dimming button once can increase a level of brightness when in ON
- Long press the dimming button can continuous to increase the brightness until release or reach the brightness.
- Short press the dimming button(up) 2 times continuously when in ON/OFF status to turn quickly to the brightness.
Dimming Button (Down)
- Short press the dimming button once can decrease a level of brightness when in ON
- Long press the dimming button can continuous to decrease the brightness until release or reach the brightness.
- Continuous short press 2 times when in ON/OFF status to turn quickly to the brightness.
Accessory Information
Tools Needed To Install
Φ5mm Philips Screwdriver | Test Pencil |
---|---|
Electrical Tape | Plier |
Cutter | Ruler |
4.Installation
4.1.1 Installing the base to fixed the remote control (Installation the junction box with panel)
-
Installation the Junction box auxiliary bracket on the Junction box
-
Secure the junction box bracket securely with the mounting screws provided
.1.2 Installing the panel
- Installing the panel base on the Junction box bracket and tighten with the matched
Wall installing with panel
- according to the junction box bracket hole, drill two holes on the wall, and into the expansion bolt, with mounting screws to junction box support
Installing the panel
-
Installing the panel base on the Junction box bracket and tighten with the matched
-
Put the panel on the panel base , press gently to make it to make sure it installed firmly. Panel base
-
Wall installing without panel
- Mode one :
Peel off the wall bracket’s stripping layer of back adhesive and attach the wall bracket to the wal
Mode two:
according to the wall bracket hole, drill two holes on the wall, and into the expansion bolt, the wall bracket with mounting screws fixation.
Remote control battery replacement
-
Hold the card buckle both ends of the battery compartment pull it out ,then remove the battery
-
remove the old battery from the battery holder, change new battery (CR2032), Reinstall the battery box on the remote
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>