Habitat et Jardin 1536-128813 Infrared Heater Instruction Manual

Habitat et Jardin 1536-128813 Infrared Heater

Product Information

• Model: SUNDEAR XD-YS
• Power Supply: 220-240V AC
• Power Output: 1500W/2000W
• Frequency: 50/60 Hz
• Dimensions: 56 x 10.6 x 7.2 cm
• Weight: 1.4 kg

Product Usage Instructions

1. Before starting the installation process, make sure you have the following tools: pencil, hammer, level, screwdriver, power drill, and drill bits.
2. The heater comes with a wall mounting bracket specifically designed for ceiling installation. Ensure that the ceiling is solid and free from hidden water pipes or electric wires.
3. The heater should be installed at least 19.7 inches (50 cm) away from side walls and at least 2.4 meters off the floor.
4. The appliance must be installed on solid surfaces such as concrete, wood, or metal.
5. Make sure the supply cables are well mounted and do not come into contact with the reflector of the heater or trail into the heated area. The supply cable can be fixed to the metal mounting bracket behind the heater using plastic zip ties.
6. It is recommended to have the heater installed by a qualified electrician.
7. Always disconnect the heater from the electricity supply and allow it to cool before starting the installation process.
8. If ceiling mounting, ensure that the lowest part of the heater is located at or above a minimum height of 2.4 meters from ground level to prevent accidental contact when in operation.
9. For ceiling mounting, maintain a distance of 2.4 meters between the appliance and the ground.
10. When installed to the ceiling, there must be a minimum distance of 0.5 meters between corners and the appliance.
11. The distance between the heater and living beings should be a minimum of 1 meter.
12. Maintain a minimum clearance of 0.5 meters between the front side of the heater and materials such as wood, carton, cloth, etc.
13. If using the heater outside, it is recommended to use a weatherproof outlet.
14. Before drilling, ensure there are no wires or water pipes in the area where the heater is to be installed.
15. The heater must be installed on the provided mounting brackets.
16. Securely fasten the brackets to the mounting surface and the backside of the heater using the supplied nuts and screws.
17. Securely fasten the heater on the brackets using the nuts and bolts provided.
18. The brackets can be used to adjust the direction of the heater. Loosen the brackets to adjust the heater angle.

AFTER-SALES SERVICE/INFORMATION/VIDEO/CONTACT

Warning
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE,
We cannot be liable for any damages caused by failure to observe these instructions.
CAUTION : FOR OUTDOOR USE ONLY

IMPORTANT SAFETY INSTRUCTIONS

READ CAREFULLY-The infrared heater is designed for safe operation. Nevertheless, installation, maintenance and operation of the heater can be dangerous. Observing the following procedures will reduce the risk of fire, electric shock, injury to persons and keep installation time to a minimum. Save these instructions for future used.

1. Read all instruction before using this heater.
2. Remove the unit from its packaging and check to make sure it is in good condition before using.
3. Do not let children play with parts of package (such as plastic bags).
4. Check the household voltage to ensure it matches the heater’s rated specification.
5. Check the power cord and plug carefully before used, to make sure that they are not damaged.
6. Before unplugging the power cord, be sure to turn off the power, when energizing the unit, be sure your hands are dry to prevent from electric shock.
7. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear.
8. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
9. Do not use near or in the immediate vicinity of a bath or swimming pool or any source of liquid.
10. To protect against electric shock, do not immerse cord or plug in water or any other liquid.
11. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire or damage to the heater.
12. Always unplug the heater when not in use.
13. Connect to properly grounded outlets only.
14. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
15. Do not allow cord to overhang the countertop where it can be easily pulled by children.
16. Do not put fingers or foreign objects into the grill while in operation.
17. Do not leave the appliance unattended when in use.
18. This heater is not intended for use in bathrooms, laundry, and similar indoor locations, never located heater where it may fall into a bathtub or other water container.
19. No liability can be accepted for any damage caused by non compliance with these instructions or any other improper use or mishandling.
20. This appliance is not intended for use by persons (including children) with reduces physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children and vulnerable people should be supervised to ensure they do not play with the appliance.
21. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
22. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Disconnect power at service panel and have heater inspected by a reputable electrician before reusing. If the supply cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified person to avoid a hazard.
23. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
24. To disconnect heater, turn controls to off, then remove plug from outlet.
25. To prevent overheating of this appliance, keep the air inlets and outlets clean and free of anything that may cause blockage. Check all inlets and outlets from time to time to ensure it is clear of any dirt or dust accumulation. DO NOT COVER.
26. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
27. Parts of the heater may exceed 200℃, contact with the heating tube, reflector, or metal parts near the heating tube, may cause severe BURNS. To avoid burns, do not let bare skin touch hot surface.
28. NEVER place hands under the heating elements. ALWAYS allow heating element to cool at least 10 minutes before touching the heating tube or adjacent parts.
29. This product contains recyclable materials. Do not dispose this product as unsorted municipal waste. Please contact your local municipality for the nearest collection point.

SAVE THESE INSTRUCTIONS

Introduction

This robust and weatherproof heater is designed for domestic and commercial heating applications at outdoor well-protected areas.

Voltage(V)

|

220-240V AC

Wattage(W)| 1500W/2000W
Hertz(Hz)| 50/60
Dimensions W×H×D(mm)| 5610.67.2cm
Weight(KG)| 1.4KG

INSTALLATION

Tools Needed:

• Pencil Hammer Level Screwdriver Power Drill and drill bits
  A wall mounting bracket is provide with the heater which has been specifically designed to allow this product to be fitted to a ceiling before drilling the holders for the ceiling is solid and that there are no hidden water pipes or electric wires. The heater must be installed no less than 19.7ʺfrom side walls and no less than 2.4m off the floor.
  ATTENTION! The appliance must be installed on the solid surfaces like concrete, wood, or metal etc.
  Important : Ensure that the supply cables are well mounted and that it does not meet reflector of the heater or that does not trail into heated area, the supply cable can be fixed to the metal mounting bracket behind heater with plastic zip ties.

  1. This heater should be installed by a competent person, i.e., a qualified electrician.
  2. Always disconnected the heater from the electricity supply and allow it to cool before installation.
  3. For ceiling mounting, the lowest part of the heater must be located at or above a minimum height of 2.4m from ground level, so that the heater cannot be touched when in operation.
  4. For ceiling mounting, there must be a 2.4m distance from your appliance to the ground.
  5. When installed to the ceiling, there must be 0.5m between corners and the appliance.
  6. The distance of your appliance from the living beings is to be min 1m.
  7. The distance from the front side of the heater to materials such as wood, carton, cloth etc., must be min 1m.
  8. When mounting to a ceiling, do not position the heater at an angle more than 90°and less than 45°.
  9. The supply cable must be at the lower end of the heater if the heater is installed at an angle or vertically.
  10. Keep the supply cord away from the body of the heater which will get hot during use.
  11. Do not install the heater on an inflammable surface.
  12. Observe the minimum safe distance between the heater body and the inflammable surfaces when mounted.
  13. The heater should always have a minimum clearance of 0.5m from a ceiling and adjacent wall.
  14. If the heater is to be used outside, a weatherproof outlet is recommended.
  15. Before drilling ensure that there are no wires or water pipes in the area where the heater is to be installed.
  16. The heater must be installed on the mounting brackets provided.
  17. Fasten the brackets securely to the mounting surface and the backside of the heater using the nuts and screws supplied.
  18. Fasten the heater securely on the brackets using the nuts and bolts supplied.
  19. The brackets can be used to adjust the direction of the heater, adjust the heater angle by loosening the two bolts on the wall mounting bracket, tighten the bolts again when the desired angle is reach

Correct Installation Position – 01

Note : Mounted angle with 300-45 0

Position – 02 Note: Heater should be wall or ceiling mounted under well pro- tected enviornments, at least keep 3feet (0.9m) away from any combusitble objects.

Note : Do not cover.

Warning – to reduce the risk of fire

• Caution : Keep combustible materials, such as furniture, pil- lows, curtains at least 3feet (0.9m) from the front of the heater and keep them away from the sides and rear.

• Caution : Do NOT use with an extension cord or relocatable power tap (out- let/power strip).

• Caution : Hot surface, do NOT touch.

• Caution : Do NOT cover with any objects such as blanket on the heater.

ASSEMBLY INSTRUCTIONS

• a) The heater must be properly installed before it is used.
• b) The heater can be using at indoor or well protected outdoor area,
• c) User-operated devices intended to reduce the risk of fire, electric shock, or injury to persons; must be follow instruction
• d) Do not change the heater structure without registered electrician advice

Installation Accessories

Wall mounted installation

Ceiling mounted installation

The heater must be installed at least 2.4M above the floor grade
Attention : cable should not pass thought the heater

FUNCTION & OPERATION

1. PLUG the unit into a plug socket, make sure the power supply is the same as rated
2. PRESS the power switch on the back side of heater, on and off the heater.

Troubleshooting

1. If heater will not power cord is plugged into an electrical outlet, if not, plug in.
2. Check if electricity to the main fuse is working

MAINTENANCE

Attention! Careful and regular maintenance of your heater considering our instructions assume great importance to attain a long efficient operation of your appliance.

1. Check the filthiness of the Reflector and IR-Filament at least once a month. If necessary, apply cleaning and maintenance instructions.
2. The number of checks may be increased considering the amount of the dust in the environment.
3. Check the deformation of the Reflector, Wire and Frame visually while cleaning the appliance. In case of deformation, consult to your technical service.
4. Check the Power Cord and Plug visually while cleaning the appliance. In case of deformation, consult to your technical service.

CLEANING

Regular and careful cleaning helps your infrared heater operate efficiently for many trouble free years. To clean your heater, follow steps below:

1. Unplug the power cord for your safety before cleaning your appliance.
2. Make sure the heater is cool before continuing.
3. To keep the heater clean, the outer shell maybe cleaned with a soft, damp cloth. You may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth. (CAUTION: DO NOT let liquids enter the heater).
4. DO NOT use alcohol, gasoline, abrasive powders, furniture polish or rough brushes to clean the heater. This may cause damage or deterioration to the surface of the heater.
5. DO NOT immerse the heater in water
6. Wait until the heater is completely dry before use.

Storage : Store the heater in a cool, dry location when not in use to prevent dust and dirt build up. Use packaging carton to store.
ATTENTION:

1. Always disconnect the heater from the electricity supply and allow it to cool before attempting to work on it.
2. If the heater has collected dust or dirt inside the unit or around the heating element, have to unit cleaned by a qualified service agent. Do not operate the heater in this condition.
3. The only maintenance required is cleaning of the external surfaces of the heater.
4. Do not touch the heating element with bare fingers, as residue from your hand could affect the life of the lamp. If it is accidentally touched, remove the finger marks with a soft cloth moistened with mentholated spirit or alcohol.
5. Do not attempt to repair or adjust any electrical or mechanical functions on this heater.
6. The heater contains no user serviceable parts. Should the product suffer damage or breakdown, it must be returned to the manufacturer or its service agent.
7. Damaged supply cords to be replaced by the manufacturer, service agent or similarly qualified person to avoid hazard.

RECYCLING

At the end of the electrical product’s useful life, it should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice in your country.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>