Theater Solutions TS6DV 6 Zone Speaker Selector User’s Manual
- June 12, 2024
- Theater Solutions
Table of Contents
Theater Solutions TS6DV 6 Zone Speaker Selector
Front Panel
- Master Source Switch (Select A or B)
- Rotary Style Volume Control Knob – six total one for each of six individual zones
- Six individual Zone on/off, slotted buttons for easy labeling
Back Panel
- One Source A and B input, removable connector
- Three Output Removable Connectors, Zones 1 & 2, Zones 3 & 4, and Zones s & 6
Typical Hookup
- Dual Source; choice of A or B input, Master A or B Switch on the front panel
- 3 Dual Zone Connectors, stereo right and left positive and negative connections
Installation
Make sure your receiver or power amplifier is turned off before doing any wiring.
- When connecting wire, use a wire stripper and strip 3/8″ of insulation from the end of the wire. To avoid short circuits and possible amplifier damage, do not strip too much insulation from the wire. Tightly twist the end of the wire so that there are no frayed wires.
- For wiring convenience, unplug connectors from the connector block. Verify that there are no wire frays. Insert the wire and tighten the terminal screw using a small screwdriver. Connect the wires from the speaker output from your receiver or amplifier to the TS6DV terminals marked AMPLIFIER. Pay attention and connect the”+” output from the right front output on the amplifier to the right”+” input on the TS6DV and connect the”-” output from your amplifier to the”-” input on the TS6DV. Likewise, connect the left channel wires to the left input of the TS6DV.
- Next, connect the wires from each of the speakers to the corresponding connection on the TS6DV. If you are using a second amplifier, connect it to the AMP B terminal. Plug connectors back into the unit.
Warning: Be sure connectors are plugged in correctly, do not shift over one pin.
Installation Tips
- Theater Solutions recommends using 16 AWG gauge stranded wire. For runs longer than 50′, 14 gauge is recommended.
- You can mix 4, 6, 8, and 16-ohm speakers.
- Since speakers have different efficiencies, more efficient speakers will sound louder than less efficient speakers. Select speakers with the same efficiencies (i.e. sensitivity: a typical measurement is 9odB/ Watt)
- Wire according to state and local laws. Most states or counties require in-wall speaker wires with a specific “CL” fire rating. CL2 is for residential only; CL3 is approved for both residential and commercial applications. This cable is available from Theater Solutions or consult your dealer.
- Keep the speaker wiring from running close to AC power wiring for safety and to avoid any noise pick up.
Operation
For initial connection, Theater Solutions recommends selecting one speaker pair located closest to the room where you are operating the TS6DV. Select this speaker pair and turn on your receiver/ amplifier. Make sure sound is coming from both speakers. Before you turn on additional speakers, read the information below.
This Volume Control is a passive device (no power supply) that takes a signal from the source and allows you to attenuate or turn the sound down. It does not add or increase the gain. Its main function is to provide impedance matching of your speakers to the amplifier or receiver to which the TS6DV is connected. This is especially important when playing more than 2 pair of speakers at once. Each internal volume control has impedance jumpers that allow users to select 1x, 2x, 4x, or Bx. These settings correspond to the number of speaker pairs you will be adding to each zone and should be adjusted accordingly. The default is 4x for each. Changing the settings involves removing the cover of the speaker selector. If you have questions regarding changing these jumper settings you should first call our tech support at Theater Solutions to walk you through the procedure.
Level Controls: Turning the level control fully counterclockwise will
reduce the level of sound to fully muted. Turning the level control clockwise
will increase the volume in approximately 3 dB to 6dB increments
(depending on which of the 12 steps for a total of 54 dB).
Note: even though there is no sound coming out of the speakers when turned fully counterclockwise, the volume control is still engaged and drawing signal to its transformers. Theater Solutions recommends using the on/off switch for the respective zone to fully turn the volume control off.
Refer to your amplifier or receiver’s user manual or on the rear panel of the unit to determine the minimal speaker impedance that your amplifier can handle.
Thank You for your purchase of your new Theater Solutions Speaker Selector!
Theater Solutions TSGDV speaker selector series has been designed to let you add speakers around your home or office while maintaining central control. Turn them on and off to adjust the volume without requiring additional amplifiers.
- Connect and control up to 6 independent zones with Dual Source (A or B Master Switch)
- Automatic, adjustable (internal) impedance-matching protection circuitry
- 6 individual rotary-style internal volume controls with 12 steps 54dB attenuation
- Easily labeled, front-mounted slotted push on/off button control
- Heavy duty, removable input/output connectors accept up to 14ga speaker cable
- Isolated left/ right circuit grounds for amplifiers with floating grounds or bridged configurations
- Advanced design for easy installation and hassle-free operation
- The brushed aluminum front faceplate
FREQUENTLY ASKED QUESTIONS
What is the Theater Solutions TS6DV 6 Zone Speaker Selector used for?
The Theater Solutions TS6DV 6 Zone Speaker Selector is used to distribute audio signals from a single amplifier or receiver to up to six different zones or sets of speakers.
How many audio zones can the TS6DV speaker selector support?
The TS6DV speaker selector can support up to six audio zones, allowing you to control audio output to different areas in your home or commercial space.
Can I use the TS6DV speaker selector with any amplifier or receiver?
Yes, the TS6DV speaker selector is compatible with most amplifiers and receivers, as long as the power output and impedance ratings are within the specified range.
What is the purpose of using a speaker selector in a multi-room audio system?
The speaker selector allows you to play audio from a single source (amplifier or receiver) in multiple rooms or zones simultaneously, enabling a multi-room audio setup.
Does the Theater Solutions TS6DV have individual volume controls for each zone?
The TS6DV speaker selector does not have individual volume controls for each zone. It functions as an on/off selector for each zone.
How does the TS6DV speaker selector handle impedance matching?
The TS6DV speaker selector typically has impedance protection to ensure that the connected amplifier or receiver sees a safe and stable load.
Can I use the speaker selector to play different audio sources in each zone?
No, the TS6DV speaker selector is designed to distribute audio from a single source to multiple zones simultaneously. It does not support different audio sources for each zone.
Is the TS6DV speaker selector suitable for both residential and commercial applications?
Yes, the TS6DV speaker selector is suitable for both residential and commercial audio distribution setups.
Can I use the speaker selector with outdoor speakers?
Yes, the TS6DV speaker selector can be used with outdoor speakers, as long as the speakers' power handling and impedance ratings are within the specified limits.
Does the speaker selector support passive or active speakers?
The TS6DV speaker selector is designed to work with passive speakers that do not require an external power source.
How do I connect the TS6DV speaker selector to my amplifier or receiver?
You connect the speaker selector to the amplifier or receiver's speaker outputs using standard speaker wire connections.
Can I add volume controls to each zone when using the speaker selector?
Yes, you can add external volume controls to each zone if you want independent volume adjustment for each zone.
Can I use the speaker selector with in-ceiling or in-wall speakers?
Yes, the TS6DV speaker selector can be used with in-ceiling or in-wall speakers, as long as they are passive and within the specified impedance range.
Does the speaker selector support automatic impedance matching?
Some higher-end speaker selectors may have automatic impedance matching capabilities, but the TS6DV speaker selector typically relies on manual setup.
Can I use the TS6DV speaker selector with a whole-house audio distribution system?
Yes, the TS6DV speaker selector is commonly used in whole-house audio systems to distribute audio to different zones or rooms.
DOWNLOAD THE PDF LINK:Theater Solutions TS6DV 6 Zone Speaker Selector User’s Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>