metabo KB 18 BL Cordless Cooling Box Instructions

: June 12, 2024
: metabo

metabo KB 18 BL Cordless Cooling Box

| KB 18 BL

*1) Serial Number: 00791..

---|---
U| V| 18 / 12 / 220-240 ~
W D| kWh| 55
I| l| 24
I B| l| 29
T Temp| °C| 18
K Class| –| ST
L Eco| dB (A)| 34
L Max| dB (A)| 54
A 0| mm| 490 x 425 x 325
A B| mm| 815 x 520 x 430
m| kg| 6,3
W| kWh| 0,149 kWh / 24 h (230 V)
P C| W| 50 W (18 V), 42 W (12 V), 50 W (220-240 V ~)
P W| W| 48 W (18 V), 40 W (12 V), 43 W (220-240 V ~)
F 12V| A| 5

2) 2014/35/EU, 2014/30/EU, 2011/65/EU, 2009/125/EC
3) EN 60335-1, EN 60335-2-24, EN IEC 63000

2021-07-15, Bernd Fleischmann Signature
Direktor Produktentstehung & Qualität (Vice President Product Engineering & Quality)
*4) Metabowerke GmbH – Metabo-Allee 1 – 72622 Nuertingen, Germany

Declaration of Conformity

We, being solely responsible: Hereby declare that this cooling box, identified by type and serial number 1), meet all relevant requirements of directives 2) and standards 3). Technical documents for 4) – see page 3.

For UK only:
We as manufacturer and authorized person to compile the technical file, see 4) on page 3, hereby declare under sole responsibility that these cooling box, identified by type and serial number 1) on page 3, fulfill all relevant provisions of following UK Regulations S.I. 2016/1101, S.I. 2016/1091, S.I. 2012/3032, S.I. 2011/1524 and Designated Standards EN 60335-1, EN 60335-2-24, EN IEC 63000.

Specified Conditions of Use

This cooling box is suitable for cooling or keeping warm packaged food and beverages.

It is intended for private use when camping, inside the car or similar. It is not intended for industrial or commercial use.

Not intended for outdoor use.

Not intended for use in areas subject to special conditions such as corrosive or explosive atmospheres (dust, steam or gas).

The device may not be exposed to rain.

Pay attention to country-specific regulations and laws.

The user bears sole responsibility for any damage caused by inappropriate use.

Generally accepted accident prevention regulations and the enclosed safety information must be observed.

General Safety Information

For your own protection and for the protection of your electrical device, pay attention to all parts of the text that are marked with this symbol!
WARNING – Read the operating instructions to reduce the risk of injury.
WARNING Read all safety warnings and instructions. Failure to follow all safety warnings and instructions may result in electric shock, fire and/or serious injury.

Keep all safety instructions and information for future reference.

Pass on your power tool only together with these documents.

Special safety instructions

Check the device for damage. A damaged device may not be put into operation.

This device can be used by children from 8 years of age and, in addition, by persons with impaired physical, sensory or mental ability or lack of experience or knowledge if they are supervised or have received induction training on the use of the device and understand the associated risks. Children may not play with the device. Cleaning and user maintenance may not be performed by children unless supervised.

Keep packaging film away from children. Choking hazard.
Prior to all maintenance and cleaning jobs: Disconnect the device from the power supply. Pull the plug, remove battery pack.

Disconnect the device immediately
from the power supply, …
… if liquid or objects have entered inside the lid.
… if the device was exposed to rain, humidity or liquids.
… if the device does not work properly,
… if the device has fallen down,
… in the event of smoke emission,
… in the event of unusual noises or smells,
… in the event of damage. In all these cases: Pull the plug and remove the battery pack. Do not continue to use. Have the machine checked by a trained specialist and repaired if necessary. See section

Do not inhale smoke from a device fire. However, should you have inhaled smoke: consult a doctor, smoke can be harmful to your health.
Do not modify the device.
When transporting the device in a vehicle secure it against movement. Do not transport in the passenger compartment, but in the luggage compartment.
Risk of accident. Position the connection cables in such a way that no one is obstructed.
Do not use both connection cables at the same time to avoid damage.
Keep the connection cables away from sharp edges, do not bent, do not tie together and do not place anything on them.
Fire hazard. Do not expose the device to high temperatures or open fire.
Do not expose to direct sunlight or heat sources.
Keep the device away from moisture, rain, wetness. No liquids may enter the device. Otherwise there is a risk of electrical shock and damage to the device. Do not use this device near water.
Never put liquids or ice in the device. Place only package food and packaged beverages in the container.
Do not expose to excessive vibrations, shocks or impacts.
Do not let any foreign objects enter the device through the ventilation slots.
Risk of overheating. Always keep the ventilation slots free, do not cover, block or do not put anything inside. Always maintain sufficient distance to walls and object so that the air can circulate freely.
Do not use adapter plugs or extension cords.
Risk of electric shock. Keep the connection cables dry. Do not touch with wet hands.
When disconnecting the power supply: Do not pull on the cable. Grab the plug instead.

Do not operate the device in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Tools create sparks which may ignite the dust or fumes.

Tool plugs must match the outlet. Never modify the plug in any way. Unmodified plugs and matching outlets will reduce risk of electric shock.

Have your device serviced by a qualified repair person using only genuine replacement parts.
This will ensure that the device functions safely.
To avoid contamination of food, the following instructions must be observed:

If the lid is opened for an extended period of time, there may be a significant rise in temperature in the compartments of the device.
Store raw meat and fish in suitable containers so that it does not touch or drip onto other food.
Regularly clean surfaces that may come into contact with food.
If the device is left empty for an extended period of time, switch off the device, defrost it, clean it and leave the lid open to prevent mould growth. ´

When not in use, disconnect the device from any power supply (mains power, power connection 12 Volt, battery pack).

Special safety instructions for battery pack and battery-powered devices

Only recharge with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

Use devices only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

When not in use, keep batteries away from paper clips, coins, keys, nails, screws or other small metal objects that could bridge the contacts. Shorting the battery terminals together may cause burns or a fire.

Under abusive conditions, liquid may be ejected from the battery. Avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C (265 °F) may cause explosion.

Follow all charging instructions and do not charge the battery pack outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

Remove the battery pack from the device before making any adjustments, changing tools, maintaining or cleaning.

Symbol Protect battery packs from water and moisture!

Do not expose battery packs to fire!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch or short circuit battery pack contacts!

A slightly acidic, flammable fluid may leak from defective Li-ion battery packs!

If battery fluid leaks out and comes into contact with your skin, rinse immediately with plenty of water. If battery fluid leaks out and comes into contact with your eyes, wash them with clean water and seek medical attention immediately!

If the device is defective, remove the battery pack from the device.

Transport of li-ion battery packs:
The shipping of li-ion battery packs is subject to laws related to the carriage of hazardous goods (UN 3480 and UN 3481). Inform yourself of the currently valid specifications when shipping li-ion battery packs. If necessary, consult your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact and no fluid is leaking. Remove the battery pack from the device when shipping it. Prevent the contacts from short-circuiting (e.g. by protecting them with adhesive tape).

Overview

Cable storage (cigarette lighter connection cable)
Cable storage (mains connection cable)
Rotary knob (switching on/off / regulate power)
Operating display “cold”
Operating display “warm”
Operating mode switch (warm, cold)
Switch for power supply
Cover
Carry handle
Container
Battery pack release button
Capacity indicator button *
Capacity and signal indicator *
Battery pack *

not included in scope of delivery/ depends on equipment

Initial Operation

Check for damage prior to commissioning. A damaged device may not be put into operation.
Before commissioning, check that the rated mains voltage and mains frequency stated on the type plate match your power supply.
Connection to mains power: Always install an RCD with a maximum trip current of 30 mA upstream.

We recommend cleaning the cooling box before first time use, see chapter 8.

Installing the carry handle

See Fig. A, Page 2.

**

Insert the carry handle (9) at the angle shown, first on one side: Insert the nose (on the carry handle) into the rectangular part of the opening (at the container joint). Then insert the carry handle also on the other side while pulling apart the carry handle slightly.

Setting up

WARNING: When setting up the unit, make sure that the power cord is not pinched or damaged.

WARNING: Do not position outlets on the back of the housing. Mains plugs must always be easily accessible.

Power supply / power connection

Battery pack
Charge the battery pack (14) before use. Recharge the battery pack if performance diminishes.
The ideal storage temperature for battery packs is between 10°C and 30°C.
In case of Li-Ion battery packs with capacity and signal display (13) (equipment-specific):

Press the button (12), the LEDs indicate the charge level.
The battery pack is almost flat and must be recharged if one LED is flashing.

Removing and inserting the battery pack
Remove the battery pack when not in use.

Removal:
Press the battery pack release (11) button and remove the battery pack.

Inserting:
Slide in the battery pack (14) until it engages.

Supply voltage 12 Volt

Take the connection cable out of the cable storage (1), unwind it completely and plug it into a suitable 12 Volt cigarette lighter socket in your vehicle.

Some cigarette lighter sockets supply power even when the vehicle engine is switched off.
A cooler that is left on could drain your vehicle’s battery to the point that the engine will not start. Unplug the cooler when leaving the vehicle.

Connection to Power Mains

Take the mains connection cable out of the cable storage (2), unwind it completely and plug it into a suitable mains power outlet.

Use

Not intended for continuous operation. The maximum operating time is 6 days. When the maximum operating time is reached, switch off the device for at least 2 hours.

Connect to the power supply

See chapter 6.3.

Set the power supply used

Set using the switch (7).

= cigarette lighter socket
= battery operation
= mains power outlet

Operating mode selection

Set operating mode using switch (6):
“COLD“ = cool
“OFF“ = OFF
“WARM“ = keep warm

Switching on/off, setting the power

Switching on: Turn rotary knob (3) in clockwise direction.

Increase power: Turn rotary knob (3) in clockwise direction.

Reduce power: Turn rotary knob (3) in anti-clockwise direction.

Switching off: Turn rotary knob (3) in anti-clockwise direction until the stop (to the “OFF” position).
“OFF“ = OFF
“ECO“ = energy saving mode
“MAX“ = maximum output

Note:
MAX position: The maximum inside temperature that can be reached is 20°C cooler than the outside temperature (at 23°C outside temperature).
A maximum inside temperature of approx. 65 °C can be reached (at 23°C outside temperature).
ECO position: The energy consumption corresponds to energy class A+++. The maximum inside temperature that can be reached is 8- 11°C cooler than the outside temperature (at 23°C outside temperature).

Opening / closing the lid

See Fig. A, Page 2.

Opening: To be able to open the lid (8): Fold the carrying handle (9) backwards. Then fold the lid (8) backwards.

Closing : Close the lid (8) and fold the carrying handle (9) forwards.

Energy saving tips

Do not expose to direct sunlight.
In cooling mode: Use already cooled food and beverages.
Do not open the lid longer than necessary, close it completely.
Ensure that air can circulate between the food.

Cleaning

DANGER! Disconnect the device from the power supply. Pull the plug, remove battery pack. There is the risk of electric shock!
DANGER! Make sure that no liquid enters the inside of the lid to avoid hazards!
Clean the lid using a slightly moistened cloth. Do not use solvents or detergents that attack plastics.
Vacuum the ventilation slots or clean with a soft brush.
Clean the inside of the container with water and dishwashing liquid. Dry well.

Troubleshooting guide

The device does not work:

Check if the plug or battery pack are inserted until the stop.
If the current selector switch (7) is in “battery pack” position: Check the charge status of the battery pack (see chapter 6.3). Charge the battery pack if necessary.
If the current selector switch is set to 12 V: Switch on the ignition of your vehicle.
Is the device switched on from the rotary knob (3) and on the operating mode switch (6)?

The device does not cool properly:

Place the device in a cooler location. Do not expose to direct sunlight.
Ensure that the ventilation slots are not covered.
Sufficient air circulation must be ensured.
Increase power: Turn power regulator (3) in clockwise direction.

The device does not warm properly:

Ensure that the ventilation slots are not covered.
Sufficient air circulation must be ensured.
Increase power: Turn power regulator (3) in clockwise direction.

Accessories

Use only original Metabo or CAS (Cordless Alliance System) battery packs and accessories. Use only accessories that fulfil the requirements and specifications listed in these operating instructions.

Chargers: ASC Ultra, ASC 30-36, ASC 145 DUO, etc.
Battery packs with different capacities. Only buy battery packs with voltage suitable for your power tool.

Note: We recommend the use of battery packs > 4.0 Ah.

Order no.: 5.5 Ah 6.25368 (LiHD)
Order no.: 8.0 Ah 6.25369 (LiHD)
Order no.: 10.0 Ah 6.25549 (LiHD) etc.

See www.metabo.com or the catalogue for a complete range of accessories.

Repairs

Repairs to electrical equipment may only be carried out by qualified electricians!
If the mains connection cable of this device is damaged, it must be replaced by the manufacturer or an authorized service centre to avoid hazard.
If any of your Metabo power tools require repairs, please contact your Metabo service centre. For addresses see www.metabo.com.
You can download a list of spare parts from www.metabo.com.

Environmental Protection

The device / the insulation must be disposed of properly. Combustible insulation blowing gas (cyclopentane) is used.
Observe national regulations on environmentally compatible disposal and on the recycling of disused devices, packaging and accessories

Packaging materials must be disposed of according to their labelling in accordance with municipal guidelines. Further information can be found at www.metabo.com in the “Service” section.

Only for EU countries: Never dispose of power tools in your household waste! In accordance with European Guideline 2012/ 19/EU on used electronic and electric equipment and its implementation in national legal systems, used power tools must be collected separately and handed in for environmentally compatible recycling.

Battery packs may not be disposed of with regular waste. Return faulty or used battery packs to your Metabo dealer!

Do not allow battery packs to come into contact with water!

Before disposal, discharge the battery pack in the electrical device. Prevent the contacts from short-circuiting (e.g. by protecting them with adhesive tape).

Technical Specifications

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U = operating voltage WD = annual energy consumption based on standard test results over 24 hours. (The actual consumption depends on use and location)
I = usable volume (contents) IB = gross nominal volume TTemp = design temperature KClass = climate class LEco = noise emission at “ECO” level LMax = noise emission at “MAX” level A0 = dimensions (h x w x d) AB = space requirements in operation (h x w x
d) to ensure sufficient air circulation and
to allow access to the chilled goods
m = weight without battery pack
W = energy consumption
PC = output (cooling)
PW = output (heating)
F12V = fuse (12 V)
Insulation: PU foam
direct current
Device of protection class II
The technical specifications quoted are subject to tolerances (in compliance with relevant valid standards).

Food grade
This symbol valid throughout the EU, identifies materials that are suitable for food contact in accordance with EC 1935/

Metabowerke GmbH
Metabo-Allee 1
72622 Nuertingen
Germany
www.metabo.com

metabo Logo