CHAMBERLAIN 050DCRJWF Garage Door Opener Instructions

CHAMBERLAIN 050DCRJWF Garage Door Opener

Product Information

The Logic Board is a component of the product with the model number 041DJ003MC, which can also replace the model number 050DCRJWF. It is important to note that the programming of this logic board may be different from older versions. The logic board is responsible for controlling various functions of the product.

When replacing the logic board, it is necessary to obtain a replacement label with a new myQ serial number. This serial number will be used to connect the opener to the network.

It is crucial to follow safety precautions when working with the logic board. Protective gloves and eye protection should always be worn when changing the battery or working around the battery compartment.

WARNING: This product contains chemicals, including lead, which are known to cause cancer, birth defects, or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.

Product Usage Instructions

1. Disconnect the power.

2. Open the front panel (A).

3. Remove the battery cover and disconnect the battery (B).

4. Disconnect the wires coming from the safety reversing sensors, door control, door lock, and cable tension monitor from the logic board (C).

5. Remove the logic board cover (D).

6. Install the new logic board and connect the wiring harnesses.
   Route the antenna through the channel in the new battery cover.

7. Adhere the new myQ serial number label over the original label on the logic board cover.

8. Disconnect all the wiring harnesses from the logic board (E).

9. Remove the four screws securing the logic board, remove the logic board (F), and discard.

10. Reprogram all remote controls and keyless entries using the myQ app to add the new myQ serial number to your account.

11. Set the door profile for the new replacement logic board. Refer to page 2 for the steps on how to set the door profile.

12. Reprogram the travel and test the safety reversal system. Refer to pages 2 and 3 for detailed instructions.

Battery Status LED

The battery status LED has a red wire (+) and a black wire (-).

Antenna

Ensure that the short antenna is not pinched by the battery door and held in place as shown in the images.

Adjustment & Identify Door Profile

To identify the door profile number, measure the full drum diameter based on the provided images. This step is crucial for proper operation. A QR code is provided for a video demonstration on how to identify and set the door profile.

Set Door Profile

1. Press and hold the black button for one second to enter Set Door Profile mode. The UP and DOWN buttons will turn a solid color.
2. Use the UP and DOWN buttons to set the Door Profile. The Learn LED button will blink and beep as you change the setting.
3. The number of Learn LED button blinks indicates the selected profile. There is no preset door profile setting.
4. Press and release the Black button to set the Door Profile. The process is now complete, and you can proceed to the Travel Learn mode.

If there is no selection within 4.5 minutes, the Door Profile selection mode will be cancelled with a long beep.

Logic Board
Model 041DJ003MC
Also replaces 050DCRJWF
NOTE: Please read these instructions as programming may be different from older programming.

WARNING
To prevent possible SERIOUS INJURY or DEATH:
electric and battery power BEFORE performing ANY service or maintenance.

CAUTION

To prevent damage to the receiver/logic board, DO NOT touch printed circuit board of replacement receiver/logic board during installation.
ALWAYS wear protective gloves and eye protection when changing the battery or working around the battery compartment.

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

FCC

NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between users/bystanders and device. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules and Industry Canada ICES standard. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Before you begin

Your new myQ® serial number is located on the replacement label with your replacement logic board. You will need this new myQ serial number to connect your opener to the network.

Adjustment Identify Door Profile

To identify the door profile number, measure the full drum diameter based on the images below.
NOTE: This step is important to ensure the proper operation of the unit. To view a video demonstration of how to identify and set the door profile, scan the QR code.

WARNING

To prevent possible SERIOUS INJURY or DEATH, follow instructions to select and set door profile for safe and proper operation.
To prevent possible SERIOUS INJURY or DEATH, after ANY changes to the door profile, reprogram limits.

Standard Lift Sectional Door

• Door Profile 1 = Standard to Heavy Weight Door* with a 4” drum (Recommended).
• Door Profile 2 = Light Weight Door with a 4” drum.
• Door Profile 3 = Heavy Weight Door* with a 6” drum.
• Door Profile 4 = Light Weight Door with a 6” drum.
  *NOTE: Drum sizes may vary by manufacturer. For Standard Lift Sectional Doors:
• Drums less than or equal to 5”, use 4” drum.
• Drums more than 5”, use 6” drum.
  Standard to Heavy Weight doors are those with solid wood interiors, wood veneer exteriors, glass windows, insulation, and/or decorations.

High Lift Door
Door Profile 5 = Tapered drum with tracks that raise to a higher elevation

Vertical Lift Sectional Door
Door Profile 5 = Tapered Drum with tracks raising vertically above the opening.

Set Door Profile

1. To enter Set Door Profile mode, press and hold the black button for one second. The UP and DOWN buttons turn a solid color.
2. To set Door Profile, press the UP and DOWN buttons. The Learn LED button blinks and beeps as you change the setting.
3. The number of Learn LED button blinks indicates which profile you have selected. There is no preset door profile setting.
4. Press and release the Black button to set the Door Profile. This process is now complete. Proceed to the Travel Learn mode.

EXITING DOOR PROFILE NUMBER SETTING
If there is no selection within 4.5 minutes, the Door Profile selection mode will be cancelled with a long beep.

Adjustment Program the Travel

Travel limits regulate the points at which the door will stop when moving up or down.
While programming the travel, the UP and DOWN buttons can be used to move the door as needed. During the Automatic Force Setup, the door will automatically open and close.

1. Press and hold the Adjustment Button until the UP Button begins to flash and/or a beep is heard. The Safety Reversing Sensors will be disconnected during the Program the Travel process.
2. Press and hold the UP Button until the door is in the desired UP position.
3. Once the door is in the desired UP position press and release the Adjustment Button. The garage door opener lights will flash twice and the DOWN Button will begin to flash.
4. Press and hold the DOWN Button until the door is in the desired DOWN position.
5. Once the door is in the desired DOWN position press and release the Adjustment Button. The garage door opener lights will flash twice. Program the Travel is now complete. If the garage door opener lights flash 5 times, then programming has timed out and the Travel Limits have not been set. Please restart the Program the Travel process.

Automatic Force Set Up
Once both the up and down positions have been manually set, the Safety Reversing Sensors will reconnect and become operational. Then, the opener will enter a force-sensing operation by automatically moving the door open and close. The garage door opener will sound an audible and visual alert before automatically opening and closing the door. The garage door opener will beep three times, confirming that the Automatic Force Setup completed successfully. Adjustment is complete.
If you hear one long beep after the door attempts to move, then the Automatic Force Set Up has not completed successfully. Please start over at step 1 of Program the Travel.

WARNING

To prevent possible SERIOUS INJURY or DEATH, after ANY changes to the door profile, reprogram limits.

Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.

• Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system.
• After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2″ high (3.8 cm) object (or 2×4 laid flat) on floor.

CAUTION

To prevent damage to vehicles, be sure fully open door provides adequate clearance.

Adjustment Test the Safety Reversal System

1. With the door fully open, place a 1-1/2 inch (3.8 cm) board (or a 2×4 laid flat) on the floor, centered under the garage door.
2. Press the remote control push button to close the door. The door MUST reverse when it makes contact with the board.

If the door stops but does not reverse:

1. Repeat Program the Travel (see Adjustment).
2. Repeat the Safety Reversal test.
   If the test continues to fail, call a trained door systems technician.

Test the Protector System®

1. Open the door. Place an obstruction in the path of the door.
2. Press the remote control push button to close the door. The door will not move more than an inch (2.5 cm).
   The garage door opener will not close from a remote control if the LED in either safety reversing sensor is off (alerting you to the fact that the sensor is misaligned or obstructed).
   If the garage door opener closes the door when the safety reversing sensor is obstructed (and the sensors are no more than 6 inches [15 cm] above the floor), call for a trained door systems technician.

Synchronize the Door Control
To synchronize the door control to the garage door opener, press the push bar until the garage door opener activates (it may take up to 3 presses). Test the door control by pressing the push bar. Each press of the push bar will activate the garage door opener.

WARNING

• Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.
• Safety reversal system MUST be tested every month.
• After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2″ (3.8 cm) high object (or 2×4 laid flat) on the floor.
• Without a properly installed safety reversing sensor, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.

Programming Remote Control

Your remote control has been programmed at the factory to operate with your garage door opener. If the remote does not work or you would like to program additional devices, follow the programming steps below.
Up to 40 Security+ 2.0® remote controls can be programmed to the garage door opener. Older LiftMaster remote controls are NOT compatible. Programming can be done through the door control or the learn button on the garage door opener. To program additional accessories refer to the instructions provided with the accessory or visit LiftMaster.com. If your vehicle is equipped with a Homelink®, you may require an external adapter depending on the make, model, and year of your vehicle. Visit www.homelink.com for additional information.

To add, reprogram, or change a 893LM remote control/877LM keyless entry pin using the door control

1. Press the navigation button below “MENU” to view the Features menu
2. Use the navigation buttons to scroll to “PROGRAM”.
3. Select “REMOTE” or “KEYPAD” to program from the program menu.
4. Remote Control: Press the button on the remote control that you wish to operate your garage door.
5. Keyless Entry: Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry keypad. Then press the ENTER button.
   The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed. Repeat the steps above for programming additional remote controls or keyless entry devices. If programming is unsuccessful, program the remote using the learn button.

Program a 893MAX remote control using the learn button on the garage door opener

1. Press and hold the program button on the remote control until the LED on the front of the remote control turns on.
2. Press and release the remote control button you wish to use and then press any other button to exit programming.
3. Press and release the Learn button on the garage door opener. The Learn LED will light. Within 30 seconds…
4. Press the remote control button programmed in step 2 until the garage door opener light flashes or two clicks are heard.
   To program other types of remote controls or keyless entries see the instructions included with the device or visit LiftMaster.com.

Add myQ serial number to myQ App
To program the Wi-Fi garage door opener to your network, refer to your owner’s manual.

Program the myQ Remote LED Light
Your garage door opener remote light has already been programmed at the factory to operate with your opener. Any additional or replacement remote lights will need to be programmed.

PROGRAM A DOOR OPENER TO THE myQ REMOTE LED LIGHT

1. Press the LEARN button on the light until the green LED comes ON.
2. Press the LEARN button on the door opener. OR On the Smart Control Panel® go to Menu > Program > myQ Accessory.
3. The code has been programmed when the remote light blinks once.

ADD THE myQ REMOTE LED LIGHT TO myQ ACCOUNT

1. Press the LEARN button on the light until the green LED comes ON.
2. Login to the myQ app and add the myQ Remote LED Light.

TO ERASE ALL PROGRAMMING FROM THE myQ REMOTE LED LIGHT
1. Press and hold the LEARN button until the LED turns off (6-10 seconds). All programming is now erased.

© 2023, The Chamberlain Group LLC Todos los derechos reservados

References

• Homelink
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>