CPS TLTWSAE Imperial Pro-Set Torque Wrench Kit Instruction Manual
- June 12, 2024
- CPS
Table of Contents
Pro-Set® Torque Wrench Kit
#TLTWSAE Imperial
(⅝, ¹¹/₁₈, ¹³/₁₆, ¹⁵/₁₆, 1¹/₁₆, 1 ⁵/₁₆)
Instruction Manual
BEFORE USE
- To retain wrench accuracy, DO NOT LOOSEN nuts, bolts, etc. USE ONLY FOR TIGHTENING.
- Apply a small amount of oil between handle and wrench body.
Note: If wrench is not used for an extended time, turn handle to lowest
torque setting on wrench body. Rotate handle in both directions while making a
few “clicks”. This re-lubricates the wrench.
INSTRUCTIONS
-
Select Wrench from case.
-
Insert END into socket. Wrench size and arrow must be same side.
Fig. 1 -
Loosen Locking Knob counterclockwise to unlock handle.
-
Select FOOT-Pound Scale Fig. 2 or INCH-Pound scale Fig. 3
-
Determine Proper Torque Setting For Equipment Being Serviced (use setting specified by equipment manufacturer).
-
To obtain torque values ending in ‘0’, align (0) and Handle Edge with Torque Value On Vertical Scale See Fig.2 and Fig. 4.
-
For torque values NOT ending in ‘0’, twist handle and align appropriate handle mark at handle edge with Torque Value On Vertical Scale.
-
Tighten Locking Knob clockwise to lock in your torque setting.
-
Tighten Equipment Fitting, Bolt, Nut Until Clicks Are Felt/Heard From Pivot Point
Note: To prevent tool damage, avoid further pressure on wrench after torque (clicks) achieved.
Example 1: Set Wrench to 7 ft/lb
a) Position wrench handle so Foot/Pound scale is visible.
b) Twist handle until “0” mark aligns with Center-line and 5 Foot/Pound
torque value.
c) Twist handle RIGHT 4 detents (1 detent = ½ Foot/Pound) stopping at the
“2” Mark on the Handle (while aligned VERTICALLY with the Center-line).
d) Final setting (5 +½ +½ +½ +½ =7)
e) Wrench is now set to 7 Foot/Pounds.
Torque Value + Handle Scale Value = Final Torque Value
| 5 | 0 | 5 |
|---|---|---|
| 5 | +½ detent | 5.5 |
| 5 | +1 detent | 6 |
| 5 | +½A detents | 6.5 |
| 5 | +2 detents | 7 |
Example 2: Set Torque Wrench to 72 in/lb
a) Position wrench handle so Inch/Pound scale is visible.
b) Twist handle until ‘0’ mark aligns with Center-line and 60 Inch/Pound
torque value.
c) Twist handle RIGHT 2 detents (2 detent = 12 Inch/Pound) stopping at first
“1” mark on handle.
d) Final setting (60 + 6 + 6 = 72)
e) Wrench is now set at 72 Inch/Pounds.
Torque Value + Handle Scale Value = Final Torque Value
| 60 | 0 | 60 |
|---|---|---|
| 60 | +½ detent | 66 |
| 60 | +1 detent | 72 |
Fig. 4
FOOT/POUND SFTTINGS On Wrench Body| HANDLE SCALE SETTING|
INCH/Pound Settings On Wrench Body
---|---|---
5| 0| 60
10| 0| 120
15| 0| 180
20| 0| 240
25| 0| 300
30| 0| 360
35| 0| 420
40| 0| 480
45| 0| 540
50| 0| 600
55| 0| 6601
60| 0| 720
65| 0| 780
70| 0| 840
75| 0| 900
80| 0| 960
STORAGE
Loosen Locking Knob. Turn Knurled Handle to lowest torque setting on Body
Scale.
Remove Wrench End and place all components back in Storage Case.
Store kit in dry location.
REPLACEMENT PARTS
_TWSAE| SAE Multi-Head Torque Wrench Set with handle, heads and case (⅝,
¹¹/₁₈, ¹³/₁₆, ¹⁵/₁₆, 1¹/₁₆, 1 ⁵/₁₆)
_XTWSAE| Set of SAE Wrench Heads ⅝, ¹¹/₁₈, ¹³/₁₆, ¹⁵/₁₆, 1¹/₁₆, 1 ⁵/₁₆ Jaw
Sizes
_XTWSAEW| SAE Torque Wrench Handle
_XTW58| ⅝” Individual wrench head
_XTW1116| ¹¹/₁₈” Individual wrench head
_XTW1316| ¹³/₁₆” Individual wrench head
_XTW1516| ¹⁵/₁₆” Individual wrench head
_XTW1L116| 1¹/₁₆” Individual wrench head
_XTW1L516| 1 ⁵/₁₆” Individual wrench head
LOCATIONS
CPS PRODUCTS, INC. U.S.A. (Headquarters)
1010 East 31st Street,
Hialeah, Florida 33013, USA
Tel: 305-687-4121, 1-800-277-3808
Fax: 305-687-3743
E-mail: [email protected]
Website: www.cpsproducts.com
|
CPS PRODUCTS CANADA LTD.
1324 Blundell Road
Mississauga, ON, L4Y 1M5
Tel: 905.615.8620, Fax: 905.615.9745
E-mail: [email protected]
Website: www.cpsproducts.com
---|---
CPS PRODUCTS N.V
Krijgsbaan 241, 2070
Zwijndrecht, Belgium
Tel: (323) 281 30 40,
E-mail: [email protected]
|
CPS AUSTRALIA PTY. LTD.
109 Welland Avenue,
Welland, South Australia 5007
Tel: +61 8 8340 7055,
E-mail: [email protected]
CPS ASIA
89 Short Street #06-06/07 Golden Wall Centre
Singapore 188216
Tel: +65-63375691, Fax: +65-63375692
Email: [email protected]
For the latest update(s) to these instructions, go to
www.cpsproducts.com
71-503 Rev. B
Torque Wrench Kit
TLTWSM Metric
(17, 22, 24, 26, 27, 29mm)
Instructions for Use
Français, Español, Deutsch and latest updates: www.cpsproducts.com