Bestway 58761E AquaDrift Automatic Pool Cleaner Owner’s Manual

Bestway 58761E AquaDrift Automatic Pool Cleaner

Product Information

• Applicable Pump: 1,500-3,200 gal./h Filter Pump or Sand Filter Applicable Pool: 22 ft. (6.7 m) and below Above Ground Pool

Product Usage Instructions

1. Installation:
2. Place the product into the water in the direction of the water hose.
3. Adjust the position of the float to make the hose float on the water.
4. Regulate the pressure relief valve as necessary.
5. Adjust the wheel driving angle.
6. How to Use the Product:
   • If the hose sinks below the water surface during operation, adjust the position of the float.
   • If adapting to a high-flow pump, refer to the operation diagram and adjust the pressure relief valve knob accordingly.
7. How to Clean the Product:
8. Clean the debris compartment by rinsing it with water to remove debris.
9. Clean the pressure relief valve filter by rinsing it with water to remove debris.
10. Clean the pool suction fitting by rinsing it with water to remove debris.
11. For the filter pump, stop the pump, block connectors A and B to avoid water flowing out from the pool, and clean the filter cartridge or replace it if necessary.
12. For the sand filter pump, disconnect the cleaner from the pool, perform a backwash, and rinse to clean the sand.
13. If there are wrinkles at the bottom of the pool, level the pool to reduce them.
14. Check and clean the debris screen inside the head.
15. Check and clean the filter cartridge or backwash the filter sand if dirty.
16. Check and remove debris from the wheel.
17. Open the water valve if it did not open.
18. Troubleshooting:

Robot does not capture the debris, moves slowly or does not
move at all.| Debris compartment is full| Clean the debris compartment. Rinse with water to remove
debris.
| Pressure relief valve filter is clogged| Clean the pressure relief valve filter. Rinse with water to
remove debris.
| Pool suction fitting is clogged| Clean the pool suction fitting. Rinse with water to remove
debris.
| The filter cartridge or sand is too dirty| For filter pump – Stop the pump, block the connector A and B to
avoid water flowing out from the pool, and clean the filter
cartridge or replace if necessary.
For sand filter pump – Disconnect the cleaner from the pool,
perform backwash and rinse to clean the sand.
| Air inside the pump| Stop the filter pump or sand filter, purge the air and start
again.
The hoses are entangled| The robot is stuck on wrinkles| Check the bottom of the pool. If there are wrinkles, level the
pool to reduce them.
| Wheel is jammed| Check to see if the debris screen inside of the head is dirty.
Clean the debris screen.
| The water valve did not open| Open the water valve.
| Damaged debris compartment or pressure relief valve filter| Return to the shop to get assistance.
The driving path of the robot cannot cover the entire pool| Hose not straightened out| Turn off the pump, reconnect the product at the diagonal
position of the pool, the water hose should be in a C shape, the
product should be placed into the water in the direction of the
water hose.
| The hose sinks into the water| Adjust the position of the float to make the hose float on the
water.
| The robot running speed is too fast| Regulating pressure relief valve.
| The wheels are not in the correct position| Adjust the wheel driving angle.

OPERATING WARNING

IMPORTANT SAFETY INSTRUCTIONS

• READ AND FOLLOW ALL INSTRUCTIONS.
• WARNING: To reduce the risk of injury, do not permit children to use this product.
• WARNING: Assembly and disassembly of this product should only be performed by adult.
• WARNING: Do not remove or obstruct the float opening while the filter pump/sand filter is operating.
• WARNING: Keep hands and hair away from the Pool Vacuum while the filter pump/sand filter is operating.
• WARNING: Do not use the filter pump/sand filter while the pool is occupied.
• WARNING: Ensure the filter pump/sand filter is unplugged before any maintenance begins or severe risk of injury or death exists. NOTE: Remove the product from the pool before placing a cover over the pool.
• NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.

PART LIST

Applicable Pump: 1,500-3,200 gal./h Filter Pump or Sand Filter Applicable Pool: 22 ft. (6.7 m) and below Above Ground Pool

INSTALLATION

HOW TO USE THE PRODUCT

If the following situations occur during operation, please operate as shown to keep the robot in the best working condition.

1. During operation, if the hose sinks below the water surface, please adjust the position of the float.
2. When adapting to a high-flow pump, if the following situations occur, please refer to the operation diagram, and adjust the pressure relief valve knob to appropriately reduce the running speed of the cleaner:
   • After the hoses are straightened out, serious hose entanglement occurred in continuous long-term operation;
   • The robot runs too fast, the wheels tip over or the wheels do not move along the bottom of the pool.
3. When the robot runs for a long time, if the running track does not cover most of the pool area, or the running track is repeated. Please adjust the wheel angle knob appropriately.
4. When adapting to 1500 gal. filter pump, please remove the brush.
   • NOTE: It is normal for the robot to leak water at the water pipe joints during the water supply process.

HOW TO CLEAN THE PRODUCT

TROUBLESHOOTING

remove debris.
Pressure relief valve filter is clogged| Clean the pressure relief valve filter. Rinse with water to remove debris.
Pool suction fitting is clogged| Clean the pool suction fitting. Rinse with water to remove debris.
**** The filter cartridge or sand is too dirty| Filter pump

–  Stop the pump, block the connector A and B to avoid water flowing out from the pool, and clean the filter cartridge or replace if necessary.

Sand filter pump

–  Disconnect the cleaner from the pool, perform backwash and rinse to clean the sand.

Air inside the pump| Stop the filter pump or sand filter, purge the air and start again.

The robot is stuck on wrinkles

| Check the bottom of the pool. If there are wrinkles, level the pool to reduce them. Check to see if the debris screen inside of the head is dirty. Clean the debris screen. Check to see if the filter cartridge or filter sand is dirty. Clean the filter cartridge or back wash the filter sand.
Wheel is jammed| Check and remove debris from the wheel.
The water valve did not open| Open the water valve
Damaged debris compartment or pressure relief valve filter| Return to the shop to get assistance

The hoses are entangled

| ****

Hose not straightened out

| Turn off the pump, reconnect the product at the diagonal position of the pool, the water hose should be in a C shape, the product should be placed into the water in the direction of the water hose.
The hose sinks into the water| Adjust the position of the float to make the hose float on the water.
The robot running speed is too fast| Regulating pressure relief valve
The driving path of the robot cannot cover the entire pool| The wheels are not in the correct position| Adjust the wheel driving angle

• ©2022 Bestway Inflatables & Material Corp.
• All rights reserved
• Trademarks used in some countries under license from Bestway Inflatables & Material Corp., Shanghai, China
• Exported by Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited
• Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong
• Distributed in North America by Bestway (USA) Inc., 3435 S. McQueen Road, Chandler, AZ 85286, United States of America
• Tel: +86 21 69135588 www.bestwayusa.com

Documents / Resources

| Bestway 58761E AquaDrift Automatic Pool Cleaner [pdf] Owner's Manual
58761E, 58761E AquaDrift Automatic Pool Cleaner, AquaDrift Automatic Pool Cleaner, Automatic Pool Cleaner, Pool Cleaner, Cleaner
---|---

References

• Home Page

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>