behringer MS-112DSP 4500W Parlante Bluetooth User Manual
- June 4, 2024
- Behringer
Table of Contents
behringer MS-112DSP 4500W Parlante Bluetooth
Packing Contents
- l Speaker
- l Remote Control
- l Use(s Manual
- l Power Cable
Specifications
- 12″ 2-Way Active DSP Speaker
- PMPO Power: 4500W
- RMS Power: 350W
- Woofer: 12″ diameter, with 3″ (75mm) KSV coil.
- Tweeter: Diameter 1.73″
- Response frequency: 45HZ-18KHZ
- Sensitivity: 122dB( +/-3dB)
- Connectivity: Bluetooth, Line In, Line out
- Includes 4 preset DSP equalization values
- Unit Measurements:
- 41.6 x 44 x 65.2CM (WxDxH)
- Unit Weight 18.6kgs
- Box Measurements: 47.5 X 39.5 X 71.5CM (D x W x H)
- Box Weight 20.9kgs
Panel Specification
- Play/Pause : Press to play a song or pause while playing a song.
- Previous: Press once to jump previous song/Press and hold to diminish the volume level. Next: Press once tu jump to next song/ press and hold to raise the volume level.
- Mode: Select an operating modality.
- EQ Presets: DSP 4 Effects (Live-Speech-Music-flat)
- Signal-Limit-Power Indicator : The power Led indicator Lights up when turn on the power switch and light up when input signal in distorted.
- Line/Mic Input: One balanced XLR connector for microphone signal input. You can use any connector. A level control can adjust the level of the input signal.
- Line/MP3 Input: One balanced XLR connector tor various inputs from devices such as Mixer. A level control can adjust the level of the input signal.
- Line Out: A balanced XLR connector is provided for connecting to other amplifiers or another powered speaker.
- TWS: Using Bluetooth TWS (True wired stereo): The speaker includes TWS function via Bluetooth. In case you have two units of the same model at hand, switch to bluetooth mode. When playing for the first time, you must choose one of the speakers as the master. Then press and hold (5 seconds) the play/pause button on the control panel to connect with another speaker. You will hear indicator sound on “right channel” coming out from main speaker and sound on “left channel” from other speaker after successful pairing. Then you can start Bluetooth operation as usual. Sound will be output from both speakers. When you turn off or change the play mode and back to Bluetooth mode, the two speakers can automatically pair to play in TWS mode. In TWS pairing for the first time, there may be a short “sa sa sa .. :· sound from the speaker which is not a malfunction. If you turn off the main speaker, TWS playback will stop.
Connection Bluetooth
- To pair the speaker with a bluetooth phone or audio device, press “MODE” repeatedly on the MP3 player until select this mode.
- Put your phone or device to be used in bluetooth device discovery mode.
- When your phone or device shows the “BLUETOOTH” device, confirm the link.
CAUTION
- Avoid exposing the speaker box to moisture. If they are set up outdoors, Be Sure they are under cover.
- Do not use nor store the equipment near wet or dap places. It may cause a malfunction or shock hazard.
- If the power cord is broken, it must be replaced by the manufacturer or service agent or qualified personnel to avoid risks.
- To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.
- Clean only with a soft, dry cloth.
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation
This device should be installed and operated with a minimum distance of 20cm
between the antenna and all persons.
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful interference to
radio or television reception, which can be determined by turning the device
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>