LUTEC P6221-PIR24 Motion Activated Floodlight Owner’s Manual

**LUTEC P6221-PIR24 Motion Activated Floodlight Owner’s Manual

**

PACKAGE CONTENTS

HARDWARE CONTENTS

(not shown actual size)

• Screw Qty. 2

• Wire Nut Qty. 2

• Foam Pad Qty. 1

• Rubber Plug Qty. 1

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING:

• Consult a qualified electrician if you are not certain about the installation process. Always install wiring connections in accordance with local code, ordinances and the National Electric Code.

• Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• This light fixture is designed to fit standard junction boxes as defined by the National Electrical Code.

• This light fixture is not dimmable.
  This Class B digital apparatus complies with Canadian ICES-005.
  NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

PREPARATION

Before beginning to assemble or installing lighting fixture, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
Estimated Assembly Time: 20-30 minutes.
Tools Required for Assembly: Phillips Screwdriver, Silicone Caulking Adhesive, Ladder.

INSTALLATION

1. Turn OFF power to work area at main circuit breaker or fuse box.
   CAUTION: Do not rely on wall switch alone to turn off power

2. Remove the screw and the mounting plate pre-assembled in the fixture (A). Put the screw a side as they will be used later.

3. Attach the mounting plate to the junction box (not included) using the two screws (AA). Then attach the foam pad (CC) to the mounting plate.
   This fixture can also be installed on the ceiling.

4. Connect the ground wire from the junction box to the ground screw on the mounting plate. Connect the white wire from the junction box to the white wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Connect the black wire from the junction box to the black wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Position all the wires inside the fixture junction box

5. Attach the light fixture (A) to the mounting plate using the screw previously removed in step 2. Then insert the rubber plug (DD).

6. After mounting the fixture, apply silicone caulking compound completely around the perimeter of the cover plate where the back of the cover plate meets the mounting surface. Silicone caulking prevents water from seeping into the junction box.

7. Turn ON power to work area at main circuit breaker or fuse box.

OPERATING INSTRUCTIONS

activate regardless of time of day. After movement has stopped or left the coverage area, the light will remain on for about 5 seconds, then turn off.
SECURITY (DISTANCE)| 1MIN| At dusk, the motion sensor becomes active. Any movement within the coverage area will cause the light to turn on.After movement has stopped, the light will remain on for the preset time limit of 1, 3 or 10 minutes, then turn off.The motion sensor will remain active throughout the night.At dawn, the motion sensor will deactivate and remain deactivated throughout the day. Movement will not cause the light to turn on.
3MIN
10MIN

NOTE:
The sensor has a 14 second warm up period before it will detect motion. When turned on, please wait 14 seconds.

CARE AND MAINTENANCE

TROUBLESHOOTING

1. No power to light.

|

1. Check that the circuit is on, wall switch is on, and there is power to light fixture.

2. There may be a poor connection between the light and supply wires inside the junction box.

|

1. Check supply wire connections.

2. The photocell may be detecting daylight or light from another source, preventing the light from coming on.

|

1. Select locations away from light sources, such as street lamps or other light fixtures.

The light stays ON.|

1. The photocell window may be covered and it is not detecting light.
2. The motion sensor may be picking up a heat source like an air vent, dryer vent, or brightly painted, heat-reflective surface.

|

1. Make sure the window is clean.
2. Repositionthe motion sensor.

The light comes on during the day.|

1. The motion sensor may be installed in a relatively dark location.
2. The TIME switch is in the TEST position.

|

1. Reposition the fixture.
2. Set the TIME to the1 min.,
3. min., or 10 min.setting.

The light flashes.|

1. There is lightning, arc welding, mobile sources, or other such unstable light.
2. The light from the fixture is being reflected back to the photocell from a nearby object such as rain gutter, overhang or another reflective surface.3.  Heat is being reflected from other objects or the lamp heads.

|

1. When choosing an installation location, try to avoid areas where unstable light sources can occur.
2. Try to reposition the fixture so that light reflected back to the detector is minimized or remove the reflector nearby.
3. Reposition the motion sensor.

3-YEAR LIMITED WARRANTY

If this product fails due to a defect in materials or workmanship within three (3) years from the date of purchase, return it along with proof of date of purchase and it will be replaced with the same or comparable model free of charge.

This warranty is void if damage or defect has resulted from accident, abuse, misuse or faulty repair. This warranty gives you specific legal rights and you may have other rights that vary from state to state.

IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL OR INDIRECT   DAMAGES OF ANY KIND ARISING OUT OF THE USE OR MISUSE OF THIS PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.

LUTEC USA LLC:
149B Houston Rd Troutman NC 28166 Ningbo UTEC Electric Co.,LTD CN8, Far East Industry Park, Yuyao, China
www.lutec.com
service@lutec.com

Please call our Customer Service line at877-714-8669 for assistance Monday – Friday 9 a.m. to 5 p.m. ES

Printed in China

References

• Home | Lutec

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>