HOLYSTONE HS440 Drone with 1080P Camera User Manual
- June 12, 2024
- HOLYSTONE
Table of Contents
- HOLYSTONE HS440 Drone with 1080P Camera
- Product Information
- Product Usage Instructions
- Preparation Before Flight
- DISCLAIMER & WARNING
- Use of Battery
- MAINTENANCE
- PACKAGE CONTENTS
- PREPARATION BEFORE FLIGHT
- APP OPERATION INSTRUCTION
- SPECIFICATIONS
- CONTACT US
- GENERAL INFORMATION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
HOLYSTONE HS440 Drone with 1080P Camera
Product Information
The HS440D is a drone manufactured by Holystone. It features a camera,
propellers, a power switch with a drone status LED, a TF card slot, and a
drone battery. The drone comes with a transmitter
that has a phone holder, power switch, joysticks, camera angle adjustment,
speed switch, and various buttons for different functions. The package also
includes a USB charging cable and a screwdriver.
Product Usage Instructions
Powering On/Off the Drone
To power on the drone, long press the power button. To power it off, long
press the power button again.
Powering On/Off the Transmitter
To power on the transmitter, short press the power switch. To power it off,
long press the power switch.
Emergency Stop
The Emergency Stop function should only be used in case of emergency during
the flight to avoid any damage or injury.
Joystick Mode
The drone has two joystick modes – Mode 1 and Mode 2:
- Mode 2: In this mode, the left joystick functions as the throttle joystick.
- Mode 1: To enter Mode 1, turn on the transmitter while holding the designated button. Release the button after the transmitter is powered on.
Preparation Before Flight
Before flying the drone, follow these steps:
- Charge the drone battery using the provided USB adapter (5V/2A). Make sure to read the instructions in the Use of Battery section of the Safety Guidelines before charging.
- Do not charge the drone battery immediately after a flight, as it may be too hot. Wait for it to cool down before charging again.
For any further information or assistance, contact Holystone at +1(855)
888-6699 or email them at usa@holystone.com (USA),
eu@holystone.com (EU), or
ca@holystone.com (CA). You can also visit
their website at www.holystone.com.
Instructions For Use Gebrauchsanweisung
7
HS440D
+1(855) 888-6699
usa@holystone.com (USA)
ca@holystone.com (CA)
www.holystone.com eu@holystone.com (EU)
English Deutsch
DISCLAIMER & WARNING
Please read this Disclaimer & Warning and Safety Guidelines carefully before using our product. This product is not recommended for people under the age of 14. By using this product, you hereby agree to this disclaimer and signify that you have read it fully. You agree that you are responsible for your own conduct and any damage caused while using this product, and any consequence. You agree to only use this product for its designed purposes and in accordance with the local laws, regulations and all applicable policies and guidelines that HolyStone may provide. 2. When using this product, please be sure to strictly abide by the specification requirements and safety guidelines stated in this document. Any personal injury, property damage, legal disputes and all other adverse events caused by the violation of any of the safety instructions or due to any other factor, WILL NOT be HolyStone’s responsibility.
SAFETY GUIDELINES
Check Before Use
æ This product is a high precision drone that integrates various electronic
stability and control mechanisms. Please be sure to configure this drone
carefully and correctly to ensure safe, accident-free operation ç Ensure that
the batteries of the drone and transmitter are clean, undamaged and fully
charged before every use. èEnsure that all the propellers are undamaged and
are installed in the correct orientation.
SAFETY GUIDELINES
é Please perform a thorough check of the product before each use. Inspectthe
integrityof the parts, any signs of cracksand wear offon the propellers,
battery power and effectiveness of the indicator, etc. If there is any problem
found after checking the drone, please refrain from using it until the problem
is resolved.
Flight Environment
Fly in Open Areas Keep in Sight
Fly Below 390 ft (120 m)
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
Avoid flying over, or near obstacles, crowds, high voltage power lines, trees,
airports or bodies of water. DO NOT fly near strong electromagnetic sources
such as power lines and base stations as it may affect the onboard compass.
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – –
DO NOT use this drone in adverse weather conditions such as rain, snow, fog,
and wind.
SAFETY GUIDELINES
Operation Requirements
æ DO NOT use this product to follow any moving vehicles. ç During the flight,
turn off the motors only in case of an emergency. è When the battery runs low,
return the drone back to your starting point. é DO NOT use this product if you
feel tired, take medicine or feel unwell and drink alcohol. ê Be aware of the
volume of noise that the drone produces. Please ensure to keep your distance
to avoid ear damage.
ë Stay away from the rotating propellers and motors.
ìDO NOT fly in any spaces where drones are prohibited. Please respect people’s right to privacy by not flying your drone close to others.
Use of Battery
æ Please ensure batteries are fitted in the correct orientation as shown in the instruction manual. ç Avoid short circuits by fitting the batteries correctly, and do not crush or squeeze the batteries as this could cause the risk of a fire or explosion. è DO NOT mix new and old batteries as this can lead to poor performance of the product. é Please dispose of used batteries carefully, do not litter and recycle where ever possible. ê DO NOT expose dead batteries to heat or fire or they may explode. ë If the device is not going to be used for an extended period of time, please remove batteries to prevent potential damage to the drone from battery leakage.
SAFETY GUIDELINES
ì Only use the USB charging cable that comes with the drone to charge the
battery. í DO NOT connect the battery directly to wall outlets or car
cigarette -lighter sockets as this will damage your battery since they have
different voltages. î DO NOT attempt to disassemble or modify the battery in
any way ï DO NOT use the battery if it gives off an odor, generates heat,
becomes discolored, deformed or appears abnormal in any way. If any of these
situations occur while the battery is in use or being charged, remove it from
the device or charger immediately and discontinue use. DO NOT pierce the
battery casing with a nail or any other sharp object, break it open with a
hammer, or step on it! Dispose or recycle this battery as it may cause
personal injury or damage to your drone. Always charge the batteries on a
fireproof surface and away from combustible materials. DO NOT charge on
surfaces that can catch fire, which includes: wood, cloth, carpet. DO NOT
immerse the battery in water or get it wet. DO NOT solder battery terminal in
any way. Keep batteries out of reach of children or pets. DO NOT short-circuit
the battery by connecting wires or any other metal object to the positive(+)
and negative(-) terminals.
Li-Po Battery Disposal & Recycling
Waste Lithium-polymer batteries must not be placed with household trash.
Please contact local environmental or waste agency or the waste agency or the
supplier of your model or your nearest Li-Po battery recycling center.
MAINTENANCE
æ Clean the drone after each use with a clean, soft cloth. ç Avoid prolonged exposure to direct sunlight and avoid buildup of heat on the drone or batteries. è This device is not waterproof and must not be submerged or subjected to water under any circumstance. Failure to keep the device completely dry will result in failure and permanent damage to the unit. Be aware that although it might be dry where you are, droplets of rain or mist from a river or waterfall could damage your drone where it is flying. é Frequently check the charging plug and other accessories for signs of damage. If any part of the device or cables are damaged, avoid use or charging until the damaged parts are replaced.
PACKAGE CONTENTS
Drone
Transmitter
Drone Battery
Propeller
Instructions For Use Gebrauchsanweisung
7
HS440D
+1(855) 888-6699
www.holystone.com
usa@holystone.com (USA) eu@holystone.com (EU) ca@holystone.com (CA)
USB Charging Cable
Instructions For Use
Screwdriver
DIAGRAM OF DRONE
3
2 1
2 3
5 4
6
1 Camera 2 Propeller B
3 Propeller A
4 Power Switch/ Drone Status LED
5 TF Card Slot 6 Drone Battery
Power on/off: Long press the power button ” ” to turn on the drone. Long press again to turn it off.
DIAGRAM OF TRANSMITTER
1 7
2
8
3
9
4
10
5
6
1 Phone Holder
5 Power Switch
9 Right Joystick
2 Short Press-Take Photo Long Press-Record Video
3 Left Joystick
4 Short Press-Takeoff/Landing Long Press-Trimmer
6 Speed Switch
7 Camera Angle Adjustment
10 Short PressUnlock/Lock Long PressEmergency Stop
8 Short Press-Return to Home Long Press-GPS Switch
Power on/off: Short press the power switch ” ” to turn on the transmitter.
Long press the power switch to turn off.
· Take Photo/Record Video Short press the ” ” button on the transmitter. The
drone status LED flashes once, and the transmitter beeps once. The camera has
taken a photo. Long press the ” ” button. The drone status LED begins to flash
slowly, which means that the camera is recording. Long press the button again
will stop video recording.
DIAGRAM OF TRANSMITTER
· Speed Switch This drone comes with two speed levels (high/low). Slide the ”
” to switch between the two speed levels. When pushing, the transmitter will
beep once to indicate low speed, twice to indicate high speed.
· Adjustment of the Camera Angles You can adjust the camera’s angle by turning
the wheel on the upper right corner of the transmitter. Scroll the wheel to
the left, and the camera tilts up. Scroll it to the right, and the camera
swings down. (The tilt range is -90° to 0°)
· Turning On/Off the GPS Mode The drone will be in GPS mode by default every
time you power on the transmitter. To turn off the GPS mode, long press the ”
” button on the transmitter. The drone status LED will turn solid yellow, and
the transmitter will long beep once.
· Return to Home (RTH) Short press the RTH button ” ” to start the RTH, the
transmitter makes a beep sound and the drone will fly back to the recorded
Home Point. Short press the RTH button ” ” again to exit the RTH procedure and
regain control of the drone.
· Emergency Stop Long press the ” ” button for about 2 seconds. All the motors
stop spinning immediately, and the drone falls to the ground.
The Emergency Stop function should only be used in case of emergency during
the flight to avoid any damage or injury.
JOYSTICK MODE
MODE 2 (Left joystick as the throttle joystick)
Left Joystick
Up
Ascend
Right Joystick
Up
Forward
Down
Descend
Down
Backward
Left
Right
Rotate Left
Left
Rotate Right
Right
Fly to Left
Fly to Right
MODE 1
To enter MODE 1, turn on the transmitter while holding the ” ” button. (Please
do not release the ” ” button until the transmitter is powered on.)
Left Joystick
Right Joystick
Up
Forward
Up
Ascend
Down
Backward
Down
Descend
Left
Right
Rotate Left
Left
Rotate Right
Right
Fly to Left
Mode switching is only possible before pairing.
Fly to Right
PREPARATION BEFORE FLIGHT
Charging Drone Battery
USB adapter (5V/2A)
Power Bank æ Connect the drone battery to the charging cable. ç Plug the
charging cable into a USB adapter (5V/2A) or a power bank to charge the drone
battery. è During charging, one indicator on the cable is solid red, the other
flashes green. When fully charged, both of the indicators (red and green) are
solid. é Charging time: about 120 minutes.
– Before charging, please read the instructions in the “Use of Battery”
section of the “Safety Guidelines” carefully! – Don’t charge the drone battery
immediately after a flight, for the temperature of the battery may be too
high. Please wait till it cools down to charge it again.
PREPARATION BEFORE FLIGHT
Install Transmitter Batteries
2
1
Slide the battery cover out, insert three AAA batteries (not included) into
the battery compartment. Then slide the battery cover back to complete the
installation. – When inserting or changing the batteries, please pay attention
to the correct polarities! – Do not mix old and new batteries, or different
types of batteries. – Exhausted batteries should be removed immediately and
disposed of properly, either in a battery collection receptacle or to the
appropriate authority.
PREPARATION BEFORE FLIGHT
App Download and Installation
iOS
Android APP on Google play
Scan the QR code, connect to the App StoreTM or GoogleTM Play and download the HolyStone-FPV application for free. Required Operating Systems: iOS 9.0 or later/Android 5.0 or later.
Drone Arms
First unfold the rear drone arms, then unfold the front drone arms.
PREPARATION BEFORE FLIGHT
Drone Battery
Installation: Push the battery into the battery compartment at the rear of the
drone. Make sure that you hear a click sound, which indicates that the battery
is firmly installed.
1
2
Remove: Press the lock button on the battery and pull it back to remove the
battery from the battery compartment. The battery should be installed firmly.
Otherwise, the flight safety of your drone may be affected. The drone may
crash due to a power-cut during the flight.
PREPARATION BEFORE FLIGHT
Propellers A Head B
B
A
Installation: æ An “A” or “B” is printed on the propeller. ç Lock the
propellers to the corresponding the arms of drone (the
motor shafts are also marked) with screws. è Rotate each screws clockwise.
Removal: For propeller removal, use a screwdriver (provided) to rotate them
counter-clockwise.
– The propeller is installed before the drone is packaged at the factory. –
The drone will not fly unless the correct propeller is installed on the
correct motor shaft.
PREPARATION BEFORE FLIGHT
TF Card
To store your photos and videos, insert the TF card (not included) into the
slot as shown above before turning on the drone. The drone supports TF card up
to 64GB .
Phone Holder
2 1
3
Expand the phone holder and place your mobile phone in it. Adjust the clamp to
secure your mobile phone.
FLIGHT
Pairing
All of the following operations on this manual uses MODE 2.
æ Long press the power ” ” button on the drone. The drone status LED begins to
flash, which means the drone is powered on.
HEAD
ç Make sure the head of the drone is pointing forward, and it is placed on a
level surface.
è After both the drone and the transmitter are turned on, the transmitter will
long beep once, indicating that the pairing is done.
FLIGHT
Connecting to Drone’s Wi-Fi
HolyStoneGPS-**
Connect your phone to the Wi-Fi network generated by the drone. You can check
the drone’s status in the HolyStone-FPV app. æ Make sure to turn off
Bluetooth, Mobile Data, and VPN. Enter your phone’s Wi-Fi settings and click
Wi-Fi to search for the Wi-Fi of the drone. (Make sure the pairing has
finished before going to the Wi-Fi settings on your phone) ç Select the Wi-Fi
network: HolyStoneGPS-**. è Wait for a couple of seconds for your phone to
connect to the drone’s Wi-Fi. é Open the HolyStone-FPV app. > The connection
between your phone and the drone is established automatically.
Because the Wi-Fi network created by the drone cannot access the Internet,
your phone may inform you in various ways, like saying the connection isn’t
secure, or there is no internet connection, etc. Please ignore these messages.
Or, in the case of getting Pop-ups, choose the option that allows you to stay
with the current Wi-Fi.
FLIGHT
Compass Calibration
The drone will perform a mandatory compass calibration before the initial
flight. So you can skip step 1 if this is the first time you fly your drone.
STEP 1: Push both the right and left joysticks simultaneously to the bottom
right corner. The transmitter beeps twice. The drone status LED starts to
flash yellow. You can proceed to step 2.
STEP 2: Keep the drone parallel to the floor, and spin it three times. Once
the transmitter beeps once. You can proceed to step 3.
STEP 3: Point the head of the drone upward, and spin the drone three times.
Once the transmitter long beeps which means that you have successfully
performed a compass calibration.
FLIGHT
GPS Signal Search
Please don’t use the GPS mode when you are indoors.
HEAD
After calibrating the compass, put the drone on a flat surface. Make sure
there are no external sources of signal interference around. The drone will
automatically perform a search for GPS signals. The search will last for about
1 minute. The drone status LED will turn solid green once the search is
finished. When in GPS mode, the drone must first search for GPS signals before
it can take off.
Gyro Calibration
FLIGHT
Push the two joysticks to the bottom left corner. The drone status LED will go
from flashing to solid, which means that the gyro calibration is done.
To enusre flight safety, we recommend that the pilot performs a gyro
calibration after every pairing or crash of the drone.
Unlocking the Motors
Short press the ” ” button on the transmitter. The transmitter beeps once, and
the motors begin to rotate. The drone is unlocked.
Short press the ” ” button again, and the motors stop immediately. The drone
is locked.
FLIGHT
Takeoff/Landing
Please turn on the GPS mode before the flight to prevent the drone from flying
away and getting lost!
Takeoff: After unlocking the motors, short press the ” ” button. The drone
will ascend to an altitude of 4 ft. You can now use the two joysticks to
control the drone’s movements in the air. Landing:During the flight, press the
” ” button again. The drone slowly descends to the ground.
RETURN TO HOME
This function can only be activated when the drone is in GPS mode. The RTH
(Return to Home) function can bring the drone back to the last recorded Home
Point. There are three kinds of RTH: Smart RTH, Failsafe RTH, and Low Voltage
RTH. Home Point: The drone will mark the first location where it receives a
strong GPS signal VDWHOOLWHFRQQHFWLRQV during the flight or takeoff as the
Home Point.
Smart RTH
When the GPS signal is strong VDWHOOLWHFRQQHFWLRQV, press the ” ” button. The
transmitter will beep once, indicating that the Smart RTH is activated. The
drone will start flying back to the Home Point automatically. During the RTH
procedure, if the pilot pushes the left joystick up or presses the ” ” button
again, the drone will exit the RTH procedure immediately.
Failsafe RTH
The Failsafe RTH will be activated when: 1. The drone receives a strong GPS
signal VDWHOOLWH FRQQHFWLRQV ; and 2. There is a pre-recorded Home Point; and
3. The connection between the transmitter and the drone is lost for more than
6 seconds. Once the Failsafe RTH is activated, the drone will start to to fly
back to the pre-recorded Home Point automatically. If the connection between
the drone and the transmitter is re-established during the Failsafe RTH
procedure, the drone will stop flying back to the Home Point, and the pilot
will regain control of the drone.
RETURN TO HOME
Low Voltage RTH
- RA: the Return Altitude set in the app setting. æ The First Stage of Low Voltage RTH: The drone status LED starts to flash red slowly and the transmitter keeps beeping. The drone enters the first stage of Low Voltage RTH. There are two possible returning procedures: (After the activation of the first stage of Low Voltage RTH, a “safety zone” with a height of 98 ft and a radius of 164 ft will be generated with the Home Point as its center. Once the drone returns to the airspace above the Home Point (thus ending the RTH procedure), it can only fly within the safety zone.)
a. If the flight altitude is higher HRA than RA and the flight distance is
larger than 16ft, the drone will
first fly back above the Home H=49 ft
Point, descend to 49ft and hover
there. The first stage of Low Home Point
Voltage RTH ends.
D=16 ft
a. Flight altitude > RA Flight distance > 16ft
b. If the flight altitude is lower than RA and the flight distance is larger than 16ft, the drone will first ascend to RA, then fly back above the Home Point and hover there. The first stage of Low Voltage RTH ends.
HRA
H=49 ft
Home Point D=16 ft
b. Flight altitude < RA Flight distance > 16ft
RETURN TO HOME
The Second Stage of Low Voltage RTH: When the drone status LED starts to flash
red quickly, and the transmitter keeps beeping, the drone will enter the
second stage of Low Voltage RTH. There are two possible returning procedures:
a. If the flight altitude of the drone is higher than or equal to 49 ft, the drone will, while maintaining its current altitude, first fly back and hover above the home point. It then slowly descends to the ground.
H>49 ft H=49 ft
Home Point a. Flight altitude 49 ft
b. If the flight altitude of the drone H=49 ft
is lower than 49 ft, the drone will
first ascend to 49 ft, fly back above
the home point, then slowly
descend to the ground.
Home Point
b. Flight altitude < 49 ft
– During Low Voltage RTH, the pilot cannot terminate the procedure. – During RTH, the drone cannot avoid obstacles. – If the GPS signal is weak or unavailabe, the RTH cannot be activated. – If the drone receives not GPS signal, and the connection between the drone and the transmitter is lost for more than 6 seconds, the RTH cannot be activated. The drone will just descend to the ground and locks its motors.
TRIMMER
You can only use this function when the drone is NOT in GPS mode. There is no
need to trim when the drone is in GPS mode.
The Forward Trim If the drone tends to drift forward: 1. Press down the ” ”
button and do not release it. 2. At the same time, push the right joystick
backward one time. 3. Depending on how the drone drifts, it may take several
pushes to balance the drone. 4. After each push, wait 2 seconds to watch the
drone’s movement. If it still drifts, push the joystick backward again. 5.
Repeat STEP 4 until the drone drifts forward no more. * You can also fix the
Backward/Sideward Trim using a similar method, i.e., pushing the right
joystick to the direction opposite the drift.
AlTITUDE HOLD FUNCTION
The drone is designed with an altitude-hold function so the drone can maintain
its altitude after you release the left joystick. (The left joystick will
automatically spring back to the middle)
APP OPERATION INSTRUCTION
The Interface
Return: Tap to return to the home screen. GPS mode System Status: Displays the
current flying status of the drone and warnings.
Signal Strength (GPS): Display the strength of the GPS signal. Battery Level
(drone): Realtime display of the current battery level of the drone.
Transmitter Signal: Displays the signal strength of the transmitter. WiFi
Signal: Display of the signal strength between the cellphone and the drone.
Hide: Tap to hide all the icons. VR Split Screen: Tap to turn on the VR mode.
Then put your cellphone into a VR headset (not included) to view the live-feed
in 3D. Screen Rotation: Tap to turn the cellphone’s screen upside down.
APP OPERATION INSTRUCTION
Flight Setting: Tap to enter the setting interface. Alter settings for flight
height/distance, etc. Multifunction: Tap to choose from various flight
functions.
Return to Home: Tap to activate the RTH function. The drone will fly
automatically back to the Home Point.
Take off/Land: Tap once, the drone will take off to a height of 4 ft. Tap
again, the drone will slowly descend to the ground.
Gallery: Tap to view the photos and videos taken by the drone camera.
Photo/Video: Tap to switch between photo taking and video recording.
Shutter: Tap to take a picture or start or stop recording a video. Camera
Settings: Tap to enter camera settings. You can choose between 2.5K and 4K
resolutions.
Tapfly 1: The drone flies along the path you draw on the screen. (Please first
tap on the map to enlarge it, then set the path.) Tapfly 2: The drone flies
along the path generated by connecting the points you tap on the screen in
order.(Please first tap on the map to enlarge it, then set the path. ) Delete:
Tap to cancel the chosen function.
Submit: Tap to submit the chosen function.
View: Tap to switch between the map view and camera view.
Flight Distance: Drone’s horizontal distance from the Home Point.
Flight Altitude: Drone’s vertical distance from the Home Point.
Zoom In/Out: Slide to zoom in and out.
APP OPERATION INSTRUCTION
Beginner Mode
The beginner mode is the default operating mode.When in beginner mode: 1.
Default orbit flight radius: 16 ft. 2. The flight distance is limited to: 0~98
ft. 3. The flight height is limted to: 0~98 ft. 4. Default return altitude: 49
ft.
9GLKZ_
9KTYUXYZGZ[Y
,ROMNZ8KIUXJ
Flight Settings On APP
(KMOTTKX
(KMOTTKX3UJKH_JKLG[RZ:[XTOZULLLUXYKZZOTMZNKLROMNZVGXGSKZKXY
5XHOZ8GJO[Y *KLG[RZLZ
dLZ
3G^*OYZGTIK
*KLG[RZLZ dLZ
3G^’RZOZ[JK *KLG[RZLZ dLZ
8KZ[XT’RZOZ[JK *KLG[RZLZ
dLZ
KLG[RZ
KLG[RZ
KLG[RZ
KLG[RZ
8KSUOTMJOYZGTIKROSOZ (_XKSUOTMZNKJOYZGTIKROSOZ_U[IGTHUUYZZNKSG^OS[SLROMNZJOYZGTIKZULZ,R_OTMZUULGX IGTIG[YKRUYOTMZNKJXUTK6RKGYKHKIGXKL[R
If you want to alter the above-mentioned parameters, please first turn off the beginner mode. You can go to the “Settings” page to modify these parameters.
8KSUOTMJOYZGTIKROSOZ
(_XKSUOTMZNKJOYZGTIKROSOZ_U[IGTHUUYZZNKSG^OS[SLROMNZJOYZGTIKZULZ,R_OTMZUULGX
IGTIG[YKRUYOTMZNKJXUTK6RKGYKHKIGXKL[R
If you want to get a longer flight distance, you can activate the “Remove
Distance Limit” function in the “Settings” and boost the max flight distance
up to 1148 ft.
Please be cautious when removing the distance limit. If the battery of the
drone is low, the drone may not be able to fly back to the Home Point!
APP OPERATION INSTRUCTION
Follow Me
When the Follow Me function is enabled, the drone will track your movement by
following the GPS signal on your mobile phone. (Before using this function,
please make sure that the connection between the drone and the transmitter is
strong and stable.)
1. Ensure the drone’s flight range is within 16~98 ft. 2. Tap the ” ” icon
first, then select the ” ” icon, and follow the instructions in the prompt box
to enter the Follow Me function — the drone will now follow the mobile phone’s
coordinates. 3. To exit Follow Me Mode, simply tap the ” ” icon on the app
interface again.
· The Follow me function can only be used if the flight range is within 16~98
ft. · The Follow me function may be difficult to activate if the mobile
phone’s GPS signal is too weak. This could be caused by signal interference
from surrounding buildings, trees, mobile network congestion, etc. · Please
use Follow Me function in an open area and be mindful of your surroundings.
The drone is NOT equipped with obstacle avoidance.
APP OPERATION INSTRUCTION
Orbit Flight
3
1.Tap the ”
” icon first. Then tap the ”
” icon. Follow the
instructions in the prompt box to activate the Orbit Flight function.
2.The drone will record its current position when this function is
activated as the circle’s center. It then flies away from it to the set radius
distance and begins to circle clockwise. (Default radius:15 ft)
3.Tap the ” ” icon again to turn off Orbit Flight.
APP OPERATION INSTRUCTION
Headless Mode
The Headless Mode is a great training tool for beginner pilots. It is also
useful when the drone is too far from the pilot (which makes it difficult to
tell its orientation). It keeps the drone traveling forward, backward, left,
or right when you move the right joystick in those directions, regardless of
which way the front of the drone is pointed.
The pilot should stay facing the same direction that the drone’s head points to when it takes off.
1. First tap the ” ” icon on the app interface, then select ” ” icon
by tapping on it. Follow the instructions in the prompt box to activate
Headless Mode.
2. Tap the ”
” icon again. The drone exits Headless Mode.
APP OPERATION INSTRUCTION
- Why is the orientation of the drone important? In normal flying mode, the control of the drone movement can sometimes be counter-intuitive for beginners. For instance, when the drone is in the air with its head pointing to your right, if you push the right joystick forward, the drone will fly to your right, instead of flying forward. With the headless mode, the drone has a fixed “head.” In Headless Mode, the drone always remembers the side its head points to during takeoff as the front side. This means that if the drone takes off with its head pointing forward, it doesn’t matter how the drone is oriented in the air, when you push the right joystick forward, the drone will fly forward. Or, when its head is pointing to you, if you push the right joystick to the left, the drone will fly to your left.
Photo/Video
Tap the ” ” icon to take a photo. Tap the ” ” icon to start a recording. Tap again to stop recording. Tap the ” ” icon to view the photos and video in the app’s gallery. é If a TF card is inserted into the drone previously, the photos and the videos will be saved to the app album, the cellphone album and the TF card. ê If no TF card is inserted, the photos and the videos will be saved to the app album and the cellphone album. To view them through the app, you need to first connect the mobile phone to the Wi-Fi network generated by the drone.
APP OPERATION INSTRUCTION
TapFly
- We strongly recommend that you maximize the map before drawing the flight path.
1. Tap on the Map” ” first, then tap the ” ” icon. Follow the instructions in
the prompt box to enter the TapFly function. Tapfly 1: Tap the ” ” icon on the
app interface. Draw a line on the screen to create a flight path, and tap ” ”
icon to submit the path. The drone will then fly along this path. Tapfly 2:
Tap the ” ” icon on the app interface, then tap a few points on the screen.
Tap the ” ” icon to submit the path. The drone will then fly along the path
created by connecting the points you tap in order. 2. Exit the TapFly function
by tapping the ” ” icon again. 3. If the flight path submission fails, you can
submit it again, or exit the function.
DO NOT fly the drone towards people, animals, small/thin objects (e.g. tree
branches and power lines) or transparent objects (e.g. glass or water). · To
download the map: æ Disconnect your mobile phone from the drone’s Wi-Fi
network. ç Connect your mobile phone to the internet. Then go back to the app
and tap on the map icon. The map will load automatically. Wait till the
loading is finished. è Reconnect your mobile phone to the drone’s Wi-Fi
network and come back to this function. · The expected and actual flight paths
may not fit perfectly.
SPECIFICATIONS
DRONE Model: HS440D Weight: 195g/6.8oz Max Flight Time: 19 minutes (per
battery) Operating Temperature Range: 32° to 104°F 6L]HïïPP8QIROGHG 123× 93 ×
60 mm (Folded)
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – –
DRONE BATTERY Capacity: 1100 mAh 9ROWDJH9 Battery Type: Lithium-ion Polymer
Battery Energy: 8.36 Wh Charging Temperature Range: 41° to 104°F Charging
Time: about 120 minutes
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – –
TRANSMITTER 2SHUDWLQJ)UHTXHQF+] Max Flight Distance: 1148 ft/350 m (outdoor
and unobstructed) Battery Type: 3 x 1.5V AAA Operating Temperature Range: 32°
to 104°F
SPECIFICATIONS
CAMERA Operating Frequency: 5180MHz Photo Resolution: 4K:3840×2160P
2.5K:2560×1440P Video Resolution: 4K:3840×2160P@15fps (in TF card)
1920×1080P@25fps (in mobile phone) 2.5K:2560×1440P@25fps (in TF card)
1920×1080P@25fps (in mobile phone) Lens: FOV 120° Max Transmission Distance:
656 ft/200 m (outdoor and unobstructed) Photo Formats: JPEG Video Formats: MP4
Supported TF Cards: Supports a TF Card (Class10 above) with capacity of up to
64 GB (Not included) File Systems: FAT32
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – USB CHARGING CABLE
Input: 5V/2A 5DWHG3RZHU:
CONTACT US
Please do not hesitate to contact us if you need further
support.usa@holystone.com (America)
ca@holystone.com (Canada)
eu@holystone.com (Europe) +1(855) 888-6699
Scan the code and chat live for online support
Scan the code to start a WhatsApp chat with us
GENERAL INFORMATION
FCC Notice: This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
The Supplier’s Declaration of Conformity is available at the following
address: https://www.holystone.com/Download/US/HS440D_FCC_sDoC.pdf
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: — Reorient or relocate
the receiving antenna. — Increase the separation between the equipment and
receiver. — Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. — Consult the dealer or an
experienced radio/TV technician for help.
GENERAL INFORMATION
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
RF Exposure The equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This device should be installed and
operated with minimum distance 20cm between the radiator & your body. This
part belongs to the drone.
RF warning for Portable device: The device has been evaluated to meet general
RF exposure requirement. The device can be used in portable exposure condition
without restriction. This part belongs to the transmitter.
IC Notice: This device is restricted to indoor use when operating in the 5150
to 5250 MHz frequency range.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
CAN ICES-003 (B) Avis d’Industrie Canada Le présent appareil est conforme aux
CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne
doit pas produire de brouillage, et
GENERAL INFORMATION
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
CAN NMB-003 (B) RF Exposure Radiation Exposure Statement: The device is
compliance with RF exposure guidelines, users can obtain Canadian information
on RF exposure and compliance. The minimum distance from body to use the
device is 20cm.
Le présent appareil est conforme Cet équipement est conforme aux limites
d’exposition aux rayonnements IC établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 20cm de
distance entre la source de rayonnement et votre corps.Cette partie appartient
au drone Avertissement RF pour appareil Portable: l’appareil a été évalué pour
répondre aux exigences générales en matière d’exposition aux RF. L’appareil
peut être utilisé en condition d’exposition portable sans restriction. Cette
partie appartient à l’émetteur
HOW TO RECYCLE THIS PRODUCT This symbol on the product or its documentation
indicates that it must not be disposed of with household waste. Uncontrolled
waste disposal may harm the environment or human health. Please separate your
device from other types of waste to recycle it responsibly. This will help to
foster the sustainable re-use of material resources. We invite you to contact
your retailer or inquire at your local town hall to find out where and how the
drone can be recycled.
GENERAL INFORMATION
BATTERY WARNING: 1. Failure to follow all the instructions may result in
serious injury, irreparable damage to the battery and may cause a fire, smoke
or explosion. 2. Always check the battery’s condition before charging or using
it. 3. Replace the battery if it has been dropped, or in case of odor,
overheating, discoloration, deformation or leakage. 4. Never use anything
other than the approval Li-Po charger to the battery. Always use a balancing
charger for Li-Po cells or a Li-Po cell balancer. It is recommended that you
do not to use any other charger than the one provided with the product. 5. The
battery temperature must never exceed 60°C (140°F) otherwise the battery could
be damaged or ignite. 6. Never charge battery on a flammable surface, near
flammable products or inside a vehicle (preferably place the battery in a non-
flammable and nonconductive container).
1HYHUOHDYHWKHEDWWHUXQDWWHQGHGGXULQJWKHFKDUJLQJSURFHVV1HYHU disassemble or
modify the housing’s wiring, or puncture the cells. Always ensure that the
charger output voltage corresponds to the voltage of the battery. Do not short
circuit the batteries. 8. Never expose the LiPo battery to moisture or direct
sunlight, or store it in a place where temperatures could exceed 60°C(car in
the sun, for example). 9. Always keep it out of reach of children. 10.
Improper battery use may result in a fire, explosion or other hazard.
GENERAL INFORMATION
11. Non-rechargeable batteries are not to be recharged. Rechargeable
batteries are only to be charged under adult supervision. 12. Different types
of batteries or new and used batteries are not to be mixed. 13. Batteries are
to be inserted with the correct polarity. 14. The supply terminals are not to
be short-circuited. Regular examination of transformer or battery charger for
any damage to their cord, plug, enclosure and other parts and they must not be
used until the damage has been repaired. 15.The packaging has to be kept since
it contains important information. 16.This toy should only be connected to the
equipment with symbol Class II.
EU RF Power (EIRP): 16 dBm (0+])
Caution 1. The max operating of the EUT is 45°C. and shouldn’t be lower than
-10°C. 2. The device complies with RF specifications when the device used at
0mm from your body. 3. Declaration of Conformity.
We, Xiamen Huoshiquan Import & Export CO., LTD hereby, declare that the
essential requirements compliance with the Directive 2014/53/EU, the RoHS
Directive 2011/65/EU and Safety Directive 2009/48/EC have been fully fulfilled
on our product with indication below: Product Name: REMOTE CONTROL MODEL/RADIO
CONTROLLED Model/Mark: HS440D/HOLYSTONE
GENERAL INFORMATION
The Statement of compliance is available at the following address:
http://www.holystone.com/Download/CE/HS440D_EU_DOC.pdf
This product can be used across EU member states. MANUFACTURER INFORMATION
Manufactured by Xiamen Huoshiquan Import & Export CO.,LTD Address: Unit 1,
Room 501, Hongxiang Building, No.258 Hubin Nan Road, Siming District, Xiamen,
China +1(855)888-6699
MADE IN CHINA(CN)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>