WORLDEYECAM 1023 Waterproof Bullet Network Camera User Guide
- June 12, 2024
- WORLDEYECAM
Table of Contents
- 1023 Waterproof Bullet Network Camera
- Waterproof Requirements
- NOTE!
- 1 Packing List
- 2 Appearance
- 2.1 Dimensions
- 2.2 Cable Connection
- 3 Mount Your Camera
- 3.1 (Optional) Install Micro SD Card
- 3.2 Wall Mount
- 4 Startup
- 5 Access Your Camera
- Disclaimer and Safety Warnings
- About This Manual
- Disclaimer of Liability
- Network Security
- Safety Warnings
- Regulatory Compliance
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
1023 Waterproof Bullet Network Camera
Waterproof Requirements
Please waterproof cables in accordance with the following instructions. User shall assume all responsibility for device damage caused by water due to improper waterproof measures.
NOTE!
- Before you start, connect all the needed cables and cut off the copper wires for the cables that you don’t use.
- Please use self-adhesive waterproof tape (supplied with some products) to protect the cables.
- Use waterproof components to protect the network cable. Waterproof the power cable separately if you don’t use it. The video cable does not need waterproof treatment.
1. Use insulation tape (not included in the package) to insulate the connection part of each cable.
2. Waterproof the cables with self-adhesive waterproof tape.
(1) Fully stretch the waterproof tape at both ends.
(2) Wrap the connection part and the cable ends tightly with waterproof tape.
Make sure the tape is fully stretched during the process.
(3) Tighten the tape at both ends to prevent water leakage.
3. Install the supplied waterproof components to the network cable in sequence.
CAUTION!
You need to mount the rubber ring onto the network cable interface first.
4. If your camera has a DC cable and you will not use it, insert the plug into the interface.
5. (Optional) After the waterproof treatment is completed, put the cables into a waterproof junction box (purchased separately).
CAUTION!
• The cable connector must not be exposed and must be kept away from water.
• Restore and fasten the device after dismounting.
• Place the power adapter in a power distribution box.
1 Packing List
Contact your local dealer if the package is damaged or incomplete. The package contents may vary with device model.
No. | Name | Qty | Unit |
---|---|---|---|
1 | Camera | 1 | PCS |
2 | User manual | 1 | Set |
3* | Waterproof components(1) | 1 | Set |
4 | Screw components(2) | 1 | Set |
5* | Mount accessories(3) | 1 | Set |
Remarks:
- means optional and supplied with certain models only.
(1) Including one or more waterproof components such as tape and plug.
(2) Including one or more items from screws, hex key, etc.
(3) Including one or more items from drill template, bracket adapter, antistatic gloves, etc.
2 Appearance
2.1 Dimensions
The device appearance may vary with device model. The figures below are for illustrative purposes only.
2.2 Cable Connection
The tail cable may vary with device model. The figure below is for illustrative purposes only.
- Power interface
- Network interface
- Audio interface
- Alarm input/output interface
3 Mount Your Camera
3.1 (Optional) Install Micro SD Card
You need to install a Micro SD card if you want to save video on an on-board SD card.
NOTE!
• Please format the Micro SD card on the camera’s Web interface before use.
• Please consult your dealer or technical support for the recommended SD card
specifications.
The SD card slot position may vary with device model. The figures below are
for illustrative purposes only.
1. Use a screwdriver to remove the two screws on the card cover.
2. Remove the card cover.
3. Insert the Micro SD card into the slot.
4. Replace the card cover and tighten the screws.
3.2 Wall Mount
Before installation, make sure the wall is strong enough to hold the device.
1. Drill holes on the wall and install plastic anchors.
(1) Paste the drill template on the wall and align the cross center with the
hole on the wall. Lead the cables across the hole on the wall.
(2) Use a Ø6-6.5mm drill bit to drill 40mm-depth guide holes according to the
positions marked by the drill template. Knock the plastic anchors into the
guide holes and ensure that they are tightened up.
2. Screw the locknut to loosen the universal joint.
3. Mount the camera onto the wall and connect all cables. Lead the self- tapping screws through the guide holes in the base and fix them on the wall using a screwdriver.
4. Adjust the shooting angle.
(1) Adjust the opening of the universal joint as needed.
(2) Tighten the locknut.
4 Startup
After installation, connect one end of the power adapter (purchased separately) to the mains power supply, and then connect the other end to the power interface to start up the device.
5 Access Your Camera
Log in to the device’s Web interface to perform management or maintenance operations.
1. Open your browser, enter the device’s IP address (192.168.1.13 by default)
in the address bar and then press Enter to open the login page.
2. Enter the username and password (admin/123456 by default) and then click
Login.
NOTE!
• DHCP is enabled by default. If a DHCP server is used in your network, your
camera may be assigned an IP address, and you need to use the assigned IP
address to log in.
• You may need to install a plug-in at your first login (close all browsers
during installation). Please follow the on-screen instructions to complete the
installation and then open the browser again to log in.
• The default password is intended only for your first login. To ensure
security, please change the password after your first login. You are strongly
recommended to set a strong password of at least nine characters including all
three elements: digits, letters and special characters.
Disclaimer and Safety Warnings
Copyright Statement
No part of this manual may be copied, reproduced, translated or distributed in
any form or by any means without prior consent in writing from our company
(referred to as us hereafter).
The product described in this manual may contain proprietary software owned by
our company and its possible licensors. Unless permitted, no one is allowed to
copy, distribute, modify, abstract, decompile, disassemble, decrypt, reverse
engineer, rent, transfer, or sublicense the software in any form or by any
means.
Export Compliance Statement
Our company complies with applicable export control laws and regulations
worldwide, including that of the People’s Republic of China and the United
States, and abides by relevant regulations relating to the export, re-export
and transfer of hardware, software and technology. Regarding the product
described in this manual, our company asks you to fully understand and
strictly abide by the applicable export laws and regulations worldwide.
Privacy Protection Reminder
Our company complies with appropriate privacy protection laws and is committed
to protecting user privacy. You may want to read our full privacy policy at
our website and get to know the ways we process your personal information.
Please be aware, using the product described in this manual may involve the
collection of personal information such as face, fingerprint, license plate
number, email, phone number, GPS. Please abide by your local laws and
regulations while using the product.
About This Manual
This manual is intended for multiple product models, and the photos,
illustrations, descriptions, etc, in this manual may be different from the
actual appearances, functions, features, etc, of the product.
This manual is intended for multiple software versions, and the
illustrations and descriptions in this manual may be different from the actual
GUI and functions of the software.
Despite our best efforts, technical or typographical errors may exist in
this manual. Our company cannot be held responsible for any such errors and
reserves the right to change the manual without prior notice.
Users are fully responsible for the damages and losses that arise due to
improper operation.
Our company reserves the right to change any information in this manual
without any prior notice or indication. Due to such reasons as product version
upgrade or regulatory requirement of relevant regions, this manual will be
periodically updated.
Disclaimer of Liability
To the extent allowed by applicable law, in no event will our company be
liable for any special, incidental, indirect, consequential damages, nor for
any loss of profits, data, and documents.
The product described in this manual is provided on an “as is” basis. Unless
required by applicable law, this manual is only for informational purpose, and
all statements, information, and recommendations in this manual are presented
without warranty of any kind, expressed or implied, including, but not limited
to, merchantability, satisfaction with quality, fitness for a particular
purpose, and noninfringement.
Users must assume total responsibility and all risks for connecting the
product to the Internet, including, but not limited to, network attack,
hacking, and virus. We strongly recommend that users take all necessary
measures to enhance the protection of network, device, data and personal
information. Our company disclaims any liability related thereto but will
readily provide necessary security related support.
To the extent not prohibited by applicable law, in no event will our company
and its employees, licensors, subsidiary, affiliates be liable for results
arising out of using or inability to use the product or service, including,
not limited to, loss of profits and any other commercial damages or losses,
loss of data, procurement of substitute goods or services; property damage,
personal injury, business 7
interruption, loss of business information, or any special, direct, indirect,
incidental, consequential, pecuniary, coverage, exemplary, subsidiary losses,
however caused and on any theory of liability, whether in contract, strict
liability or tort (including negligence or otherwise) in any way out of the
use of the product, even if our company has been advised of the possibility of
such damages (other than as may be required by applicable law in cases
involving personal injury, incidental or subsidiary damage).
To the extent allowed by applicable law, in no event shall our total
liability to you for all damages for the product described in this manual
(other than as may be required by applicable law in cases involving personal
injury) exceed the amount of money that you have paid for the product.
Network Security
Please take all necessary measures to enhance network security for your
device.
The following are necessary measures for the network security of your device:
Change default password and set strong password: You are strongly
recommended to change the default password after your first login and set a
strong password of at least nine characters including all three elements:
digits, letters and special characters.
Keep firmware up to date: It is recommended that your device is always
upgraded to the latest version for the latest functions and better security.
Visit our official website or contact your local dealer for the latest
firmware.
The following are recommendations for enhancing network security of your
device:
Change password regularly: Change your device password on a regular basis
and keep the password safe. Make sure only the authorized user can log in to
the device.
Enable HTTPS/SSL: Use SSL certificate to encrypt HTTP communications and
ensure data security.
Enable IP address filtering: Allow access only from the specified IP
addresses.
Minimum port mapping: Configure your router or firewall to open a minimum
set of ports to the WAN and keep only the necessary port mappings. Never set
the device as the DMZ host or configure a full cone NAT.
Disable the automatic login and save password features: If multiple users
have access to your computer, it is recommended that you disable these
features to prevent unauthorized access.
Choose username and password discretely: Avoid using the username and
password of your social media, bank, email account, etc, as the username and
password of your device, in case your social media, bank and email account
information is leaked.
Restrict user permissions: If more than one user needs access to your
system, make sure each user is granted only the necessary permissions.
Disable UPnP: When UPnP is enabled, the router will automatically map
internal ports, and the system will automatically forward port data, which
results in the risks of data leakage. Therefore, it is recommended to disable
UPnP if HTTP and TCP port mapping have been enabled manually on your router.
SNMP: Disable SNMP if you do not use it. If you do use it, then SNMPv3 is
recommended.
Multicast: Multicast is intended to transmit video to multiple devices. If
you do not use this function, it is recommended you disable multicast on your
network.
Check logs: Check your device logs regularly to detect unauthorized access
or abnormal operations.
Physical protection: Keep the device in a locked room or cabinet to prevent
unauthorized physical access.
Isolate video surveillance network: Isolating your video surveillance
network with other service networks helps prevent unauthorized access to
devices in your security system from other service networks.
Safety Warnings
The device must be installed, serviced and maintained by a trained
professional with necessary safety knowledge and skills. Before you start
using the device, please read through this guide carefully and make sure all
applicable requirements are met to avoid danger and loss of property.
Storage, Transportation, and Use 8
Store or use the device in a proper environment that meets environmental
requirements, including and not limited to, temperature, humidity, dust,
corrosive gases, electromagnetic radiation, etc.
Make sure the device is securely installed or placed on a flat surface to
prevent falling.
Unless otherwise specified, do not stack devices.
Ensure good ventilation in the operating environment. Do not cover the vents
on the device. Allow adequate space for ventilation.
Protect the device from liquid of any kind.
Make sure the power supply provides a stable voltage that meets the power
requirements of the device. Make sure the power supply’s output power exceeds
the total maximum power of all the connected devices.
Verify that the device is properly installed before connecting it to power.
Do not remove the seal from the device body without consulting our company
first. Do not attempt to service the product yourself. Contact a trained
professional for maintenance.
Always disconnect the device from power before attempting to move the
device.
Take proper waterproof measures in accordance with requirements before using
the device outdoors.
Power Requirements
Install and use the device in strict accordance with your local electrical
safety regulations.
Use a UL certified power supply that meets LPS requirements if an adapter is
used.
Use the recommended cordset (power cord) in accordance with the specified
ratings.
Only use the power adapter supplied with your device.
Use a mains socket outlet with a protective earthing (grounding) connection.
Ground your device properly if the device is intended to be grounded.
Battery Use Caution
When battery is used, avoid:
Extremely high or low temperature and air pressure during use, storage and
transportation;
Battery replacement.
Use the battery properly. Improper use of the battery such as the following
may cause risks of fire, explosion or leakage of flammable liquid or gas.
Replace battery with an incorrect type;
Dispose of a battery into fire or a hot oven, or mechanically crushing or
cutting of a battery;
Dispose of the used battery according to your local regulations or the
battery manufacturer’s instructions.
Personal safety warnings:
Chemical Burn Hazard. This product contains a coin cell battery. Do NOT
ingest the battery. It can cause severe internal burns and lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product
and keep it away from children.
If you think batteries might have been swallowed or placed inside any part
of the body, seek immediate medical attention.
Regulatory Compliance
FCC Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
LVD/EMC Directive
This product complies with the European Low Voltage Directive 2014/35/EU and
EMC Directive 2014/30/EU.
WEEE Directive–2012/19/EU
The product this manual refers to is covered by the Waste Electrical &
Electronic Equipment (WEEE) Directive and must be disposed of in a responsible
manner.
Battery Directive-2013/56/EC
Battery in the product complies with the European Battery Directive
2013/56/EC. For proper recycling, return the battery to your supplier or to a
designated collection point.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>