CLL MAL05 150W Area Light Instruction Manual

MAL05 150W Area Light
Instruction Manual

Specifications

Construction:

• Rugged one-piece, die-cast aluminum housing secures the thermally conductive LED panel and electrical chamber
• Low profile, 3G vibration rated compact design minimizes wind load requirements.
• Housing is completely sealed against moisture and environmental contaminants.

Optics:

• Available in IES Type III, IV, V distributions
• Light engines are available in standard 4000 K and 5000 K (70 CRI) configurations.
• Scalable Lumen Packages from 13,900 to 42,000 Lumens replaces up to 1000W Metal Halide.
• Optics is precisely designed to shape the distribution, maximizing efficiency and application spacing.
• The optics can conform to dark sky requirement.

Electrical:

• Universal 120-277 VAC or 347-480 VAC input voltage
• Standard with 1-10V dimming driver(s)
• THD: ≤20%
• Power Factor: ≥90%

Controls:

• Optional occupancy sensor
• Optional Photocell

Ambient Temperature:

• Ambient operating temperature -40˚ C to 40˚ C (-40℉ to 104 ℉).

Installation:

• Suitable for mounting heights ranging from 26-50’ in area lighting applications
• Round pole, Square pole, Slipfitter, wall mount and yoke are available.
• The design can be operated by one person to install the whole lamp

Lifespan:

• Estimated 100,000-hour LED lifespan based on IES LM-80 results and TM-21 calculations

Finish:

• It’s available in black or optional dark bronze, silvery gray or white.

Certifications:

• UL wet location listed

Note:
Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25 ℃(±5 ℃ ) specifications subject to change without notice.
Applications:
Auto dealerships, parking lots, walkways, roadways, campuses, façade lighting, grocery stores and other public areas.

PERFORMANCE DATA

ELECTRICAL DATA

Number Of Drivers| ‘Driver Current (mA)| Nominal Power (W)| INPUT VOLTAGE (V)| CURRENT (Amps)
---|---|---|---|---
1| 850| 100| 120| 0.83
100| 208| 0.48
100| 240| 0.42
100| 277| 0.36
2520| 100| 347| 0.29
100| 480| 0.21
1| 1200| 150| 120| 1.
150| 208| 0.72
150| 240| 0.63
150| 277| 0.54
2600| 150| 347| 0.43
150| 480| 0.31
1| 4300| 250| 120| 2.
250| 208| 1.20
250| 240| 1.
250| 277| 0.90
250| 347| 0.72
250| 480| 0.52
1| 5200| 300| 120| 2.50
300| 208| 1.
300| 240| 1.
300| 277| 1.
300| 347| 0.86
300| 480| 0.63

EPA OF AREA LIGHT

Item|

1

|

2 @90°

|

2 @120°

|

2@180°

|

3 @90°

|

3 @120°

|

4 @90°

---|---|---|---|---|---|---|---
100W| 0.2751| 0.5267| 0.7321| 0.6164| 0.9577| 0.9837| 0.9577
150W| 0.3111| 0.6343| 0.6464| 0.6222| 0.9335| 0.9696| 0.9335
250W/300W| 0.4097| 0.7227| 0.9919| 0.8856| 1.1986| 1.3049| 1.1986

BUG

MOUNTING

• Standard versatile mounting arm accommodates multiple drilling patterns as well as square and round poles
• Optional for cast aluminum Slipfitter mounting adapter

Mounting Options

| | |
---|---|---|---
Arm Mount (4″and 5″Square and Round poles)
Standard versatile mounting arm is simple to install and can be used with existing poles for retrofit installations.| Slipfitter Mount
An optional cast aluminum mast arm adapter secures fixture head to nominal 2-3/8”O.D. horizontal steel tenon arm.| Wall Mount
Wall Mount is easy to install for direct wall mounting with 1/2′ conduit wiring or standard J-box mounting| Yoke Mount
Die-cast aluminum trunnion is easily adapted to many surfaces and allows easy fixture aiming angles.

Mounting Dimensions

PHOTOMETRICS

Type 3 optics produce an asymmetrical pattern that directs the majority of the light forward and equally on both sides of the luminaire. In a back-to-back configuration, it creates a rectangular pattern which can extend pole spacings.

Type 4 is suitable for applications where light is primarily required forward with minimal backlight. Typical installations include perimeter poles.

Type 5 optics produce a symmetrical square distribution pattern that distributes light equally on all sides of the luminaire. Type 5 luminaires is universal for most area lighting applications

DIMENSION

unit: inch/mm

ORDERING GUIDE

Example: MAL05100W 27V XXK Y Y Y Y Y Y

Fixture Type| Wattage| Voltage| CCT| Finish| Photocell (Option)| Sensor (Option)| Mounting| Photometry| Surge Protection
(Option)
---|---|---|---|---|---|---|---|---|---
MAL05
Area Light Series| 100 100W| 27V 120-277V
48V 347-480V| 40K 4000K
50K 5000K| D Dark Bronze
B Black
W White
SG Silver Gray| P0 120-277V Photocell
P3 347V Photocell
P4 480V Photocell
Blank Without Photocell| M With 120-277V Sensor
Blank Without Sensor| SQ Square Pole Mount
SP Slipfitter Mount
WM Wall Mount
YK Yoke Mount| T3 TYPE Ⅲ Photometry
T4 TYPE Ⅳ Photometry
T5 TYPE Ⅴ Photometry| S Surge protection
(Blank) No Surge protection

Example: MAL05 150W 27V XXK Y Y Y Y Y

Fixture Type| Wattage| Voltage| CCT| Finish| Photocell (Option)| Sensor (Option)| Mounting| Photometry| Surge Protection
(Option)
---|---|---|---|---|---|---|---|---|---
MAL05
Area Light Series| 150 150W
250 250W
300 300W| 27V 120-277V
48V 347-480V| 40K 4000K
50K 5000K| D Dark Bronze
B Black
W White
SG Silver Gray| P0 120-277V Photocell
P3 347V Photocell
P4 480V Photocell
Blank Without Photocell| M With 120-277V Sensor
Blank Without Sensor| SQ Square Pole Mount
SP Slipfitter Mount
WM Wall Mount
YK Yoke Mount| T3 TYPE Ⅲ Photometry
T4 TYPE Ⅳ Photometry
T5 TYPE Ⅴ Photometry| S Surge protection
(Blank) No Surge protection

ADDITIONAL MOUNTING ACCESSORIES

POLE BRACKET

• For mounting one fixture on an existing pole

| 4″ Square Pole Mount with 2-3/8″ O.D. Tenon
No. 4SQ-SP-D
Finish: Dark Bronze
USE: For use with square, non-tapered steel and aluminum poles.
Furnished with four 5/16″ hex head stainless-steel bolts. Vertical tenon measures 2-3/8″ O.D., and is made of steel tubing. Fixtures mounted to this bracket can be adjusted both vertically and horizontally.| | 4″ Round Pole Mount with 2-3/8″ O.D. Tenon
NO. 4SQR-SP-D
Finish: Dark Bronze
USE: For use with Round, non-tapered steel and aluminum poles.
Furnished with three 3/8″ hex head stainless-steel bolts. Vertical tenon measures 2-3/8″ O.D., and is made of steel tubing.
Fixtures mounted to this bracket can be adjusted both vertically and horizontally.
---|---|---|---
| 5″ Square Pole Mount with 2-3/8″ O.D. Tenon
No. 5SQ-SP-D
Finish: Dark Bronze
USE: For use with square, non-tapered steel and aluminum poles.
Furnished with four 5/16″ hex head stainless-steel bolts. Vertical tenon measures 2-3/8″ O.D., and is made of steel tubing. Fixtures mounted to this bracket can be adjusted both vertically and horizontally.| | 5″ Round Pole Mount with 2-3/8″ O.D. Tenon
NO. 5SQR-SP-D
Finish: Dark Bronze
USE: For use with Round, non-tapered steel and aluminum poles.
Furnished with three 3/8″ hex head stainless-steel bolts. Vertical tenon measures 2-3/8″ O.D., and is made of steel tubing.
Fixtures mounted to this bracket can be adjusted both vertically and horizontally.
| Pole Bracket Accessories –Angle-Adjustment Adapter
NO. SQA-ALDA
Finish: Dark Bronze
USE: Durable brackets are engineered to provide versatile
mounting options. These arms are made from rugged die-cast aluminum. They allow optimal positioning of the light fixture to maximize the lighting effectiveness vertically and horizontally.| | Pole Bracket accessories-Tenon & Yoke Adaptor
NO. SP-TR-D
Finish: Dark Bronze
USE: The 2-3/8” OD Tenon Mount Adaptor for Yoke Fixtures is designed to mount light fixtures that are equipped with a yoke mount onto a 2-3/8” OD tenon.

WALL BRACKET

• Attaches to any flat surface
• Provides wiring access

Mid-Pole tenon Bracket

| 90° Wall Mount Bracket with 2-3/8″ O.D. Tenon
NO. WM-SP-D
Finish: Dark Bronze
USE: The 90˚ wall mount bracket with 2-3/8″ tenon attaches a floodlight to almost any surface: wall, roof, or wood pole. Provides wiring access and built-in 2-3/8″ O.D. tenon to mount a fixture with our adjustable Slipfitter. Suggested 3/8″ diameter bolts for mounting. Mounting holes are spaced 3-1/4″ apart.| | 2-3/8” OD Horizontal Tenon Mid-Pole Bracket
NO. SQ-SP-D
Finish: Dark Bronze
USE: 2-3/8” OD Horizontal Tenon Mid-Pole Bracket is designed to mount light fixture that is equipped with a adjustable Slipfitter onto a 2-3/8” OD horizontal tenon
---|---|---|---

Round External Mount Horizontal Tenon

• To mount 2/3/4 fixtures on a existing pole

| Double 90‘ Horizontal Tenon Adaptor
NO. R60-SP2-90-D
Finish: Dark Bronze
USE: The Bracket is designed to mount over 2-3/8” (60mm) O.D. vertical tenon. Two fixtures can be mounted to the Round External Mount Horizontal Tenon and adjusted horizontally| | Triple 120’ Horizontal Tenon Adaptor
NO. R60-SP3-120-D
Finish: Dark Bronze
USE: The Bracket is designed to mount over 2-3/8” (60mm) O.D. vertical tenon. Three fixtures can be mounted to the Round External Mount Horizontal Tenon and adjusted horizontally
---|---|---|---
| Double 180‘ Horizontal Tenon Adaptor
NO. R60-SP2-180-D
Finish: Dark Bronze
USE: The Bracket is designed to mount over 2-3/8” (60mm) O.D. vertical tenon. Two fixtures can be mounted to the Round External Mount Horizontal Tenon and adjusted horizontally| | Quad 90’ Horizontal Tenon Adaptor
NO. R60-SP4-90-D
Finish: Dark Bronze
USE: The Bracket is designed to mount over 2-3/8” (60mm) O.D. vertical tenon. Four fixtures can be mounted to the Round External Mount Horizontal Tenon and adjusted horizontally
| Triple 90’ Horizontal Tenon Adaptor
NO. R60-SP3-90-D
Finish: Dark Bronze
USE: The Bracket is designed to mount over 2-3/8” (60mm) O.D. vertical tenon. Three fixtures can be mounted to the Round External Mount Horizontal Tenon and adjusted horizontally

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>