Hodinky YP10487 Watch User Guide

June 12, 2024
Hodinky

Hodinky YP10487 Watch

YP10487(SECONDS CARTOON, MULTI-FUNCTION SPORT WATCH

BUTTONS

  • Button operations are indicated using the letters shown in the illustration.
  • A– Reset
  • B– Mode
  • C — EL backlight
  • D — Start I Stop
  • E — EL backlight

ATTENTION

  1. Never try to open the case or remove its back cover.
  2. Do not operate buttons underwater.
  3. Should moisture appear inside the watch, have it checked immediately by your dealer. Otherwise, it can cause erosion of the metal parts of the watch.
  4. Though the watch is designed to withstand normal use, you should avoid rough use or dropping the watch.
  5. Avoid exposing the watch to temperature extremes.
  6. Wipe the watch with a dry, soft cloth only. Avoid allowing it to come into direct contact with chemical materials, which can cause deterioration of the plastic parts of the watch.
  7. Avoid wearing the watch in electromagnetic, static conditions.

DISPLAY

  • The screen is shown below:

BACKLIGHT

The backlight that uses an EL (electro­luminescent) causes the display to glow for easy reading in the dark.

Use EL Backlight

  • In the timekeeping mode, press “C” or “E” to illuminate the display for about 3 seconds.

MODE SELECTION

  • Press “B” to change mode to mode in the following sequence:
  • Timekeeping Mode – Stopwatch Mode –
  • Countdown Mode – Alarm Mode –
  • Dual Time Mode.

TIMEKEEPING

  • 12/24H Format;
  • Hour, Minutes, Seconds,
  • Day of the week, Month, Date;
  • 100 years Calendar (2000 – 2099).

STOPWATCH

  • 1/100 second unit;
  • Measuring range:
  • 0’00″00 – 23:59’59

COUNT DOWN

  • Countdown range:
  • 23:59’59” – 0’00″00.

ALARAM

  • 5 Alarms;
  • Hourly time signal;
  • The alarm sounds at the preset time each day.

DUAL TIME

  • The time for another timezone.

TIMEKEEPING

12/24H Format

  • In the timekeeping mode, press “D” to switch between 12/24H formats.

Time Setting

  1. In the timekeeping mode, Press “A” for the seconds to flash(flashing indicated in set mode);
  2.  Press “D” to reset the seconds;
  3. Press “B” to change to the next selection;
  4. Press “D” to increase the number, press and hold to change at high speed;
  5. Repeat steps 3 and 4, the selection in the following sequence: Seconds – Hour- Minutes – Year – MonthDate;
  6. Press “A” to exit the set state, after you set (The day of the week is auto-displayed in accordance with year, month, and date setting).

STOPWATCH
A Lap Time

Hodinky-YP10487-Watch-fig- \(15\)

  1. In the stopwatch mode, press “D” to start the stopwatch;
  2. To stop the stopwatch by pressing “D” again;
  3.  Press “A” to reset the stopwatch.

Split TimeHodinky-YP10487-Watch-fig- \(18\)

  1. In the stopwatch mode, press “D” to start the stopwatch;
  2. Press “A” to display the split time, stopwatch timing continues internally;
  3. Press “A” to clear the split time and to continue time measurement;
  4. Repeat steps 2 and 3, you can measure the multi-split time;
  5. Press “D” to stop the stopwatch.

COUNTDOWN

  • When the countdown reaches zero, the alarm sounds for about 60 seconds, and press any button to break it.

Countdown Timer Setting

  1. In the countdown mode, press “A” the hour to flash{flashing indicated in set mode);
  2. Press “D” to increase the hour, press and hold to increase at high speed;
  3. Press “B” to change to the next selection;
  4. Press “D” to increase the number, press and hold to change at high speed;
  5. Repeat steps 3 and 4, the selection in the following sequence: Hour – Minutes – Seconds;
  6. Press “A” to exit the set state, after you set.

Use Countdown Timer

  1. Press “D” to start the countdown;
  2. To pause the countdown by pressing “D” again.

ALARAM

  • The alarm sounds at the preset time each day for about 60 seconds, press any button to break it.

Alarm and Chime

  • In the alarm mode, press “C “to select chime, Alarm1 -Alarm5.
  • In the chime state, press “D” to on/off the chime.
  • In the Alarm1 -Alarm5 state, press “D” to on/off the alarm.

Alarm1 Setting

  1. In the alarm mode, press “A” the hour to flash (flashing indicated in set mode);
  2.  Press “D” to increase the hour, press and hold to increase at high speed;
  3.  Press “B” to select the minutes;
  4.  Press “D” to increase the minutes, press and hold to increase at high speed;
  5.  Press “A” to exit the set state, after you set.
  6. The setting and operation of Alarm1-Alarm5 are the same.

Dual Time Setting

  1. . In the dual-time mode, press “A” the hour to flash(flashing indicated in set mode);
  2. Press “D” to increase the hour, press and hold to increase at high speed;
  3. Press “B” to select the minutes;
  4. Press “D” to change the minutes(press once change 30 minutes);
  5. Press “A” to exit the set state, after you set.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals