ZQDDBA V88 Folding Drone with Obstacles Avoidance Function Instruction Manual

V88 Folding Drone with Obstacles Avoidance Function
Instruction Manual AGE 14+
FOLDING DRONE WITH OBSTACLE AVOIDANCE
FUNCTION OPERATING MANUAL

V88 Folding Drone with Obstacles Avoidance Function

*Please read this manual carefully before operation and keep it properly for future reference.

KNOW YOUR DRONE

The drone uses the 2.4G frequency, multiple-player can operate at the some time without interference. The drone can be controlled by remote to achieve flying, flipping, fine tuning, one-key take off, one-key landing, speed control, headless mode, calibration, obstacle avoidance, camera adjustment, emergency stop, light switch and other functions.

1. Upper Casing
2. Lower Casing
3. Propeller
4. Arm
5. Battery
6. Motor
7. Camera

ACCESSORIES

Notes
Please check the number of accessories carefully (as shown abovel.Please provide proof of purchase and contact the store for replacement if any missing parts.

OPTIONAL ACCESSORIES LIST

Notes
If any of the above accessories are damaged during operation, you can contact the seller to purchase.

PRE-FLIGHT PREPARATION

1.FLIGHT ENVIRONMENT
Indoor: Spacious spaces away from barriers, crowds or pets are preferred.
Outdoor: Sunny, windless and breezy weathers are preferred.
Pleose keep the drone in sight during the flight and keep it away from barriers, high-tension cables, trees and people.
Do not fly in extreme environment, such as hotness,coldness, strong wind or heavy rain.
2.OPEN THE WINGS OPENING STEPS

1. Open the front armlclose to cameral

2. Open the back arm Fold the back armf firstly and then the ront arm when folding.

3. SSEMBLING PROTECTNE GUARD
   Align the protective frame with the arm and install it (Figure 11, press it until it is in place, and then press the position (Figure 2) up to fasten the protective frame.

4. ASSEMBLING PROPELLERS
   Align the blades with the motor shaft and install them (the arm identification must be consistent with the blade identification), Tighten the screw clockwise .

5. BATTERY CHARGING FOR DRONE
   A. Remove the lithium battery from the bottom of the drone.

6. B. The USB charging cable connects the battery to the USB power port.

Notes
LED lights on when charging and red light turn off when full charging completes.Charging time is about 150 minutes.

**** BATTERY LNSTRUCTIONS

• There is a certain risk when using lithium battery. It may cause fire, body injury or property loss. Users must be aware of the risks and take full responsibility of using battery improperly.
• If battery leakage occurs, please avoid contacting your eyes or skin with electrolyte. Once it happens, please wash your eyes with clean water and seek medical care immediately.
• Please remove the plug immediately if you sense any peculiar smell, noise or smoo.

Battery Charging

• Please use the charger from original factory to ensure your safe usage.
• Do not charge dilatant or outworn battery.
• Do not over charge battery. Please unplug the charger once fully charged.
• Do not charge the battery next to inflammables, such as carpel, timber floor or wood furniture or on the surface of electro-conductive objects. Please always keep an eye on the battery when charging.
• Do not charge battery which not cool down yet.
• The charging temperature should be between Otto 40°C.

Battery Recycling

• Do not dispose the battery as daily rubbish. Please familiarize yourself with the local garbage disposal method and dispose it according to the special requirement.

KNOW YOUR REMOTE CONTROL

1.Parts of remote control
Standard version/Obstacle avoidonce version
The regular version s aLight control key

LITHIUM BATTERY INSTRUCTION

1. Onen the remote control battery cover

2. Remote control battery installation
   Open the battery cover and insert the 3 AA batteries correctly according to the electrode instructions. (Batteries not included)

Notes

1. Make sure the battery are loaded correctly according to the polarity Indications on the battery comportment.
2. Please do not mix old and new batteries together.
3. .Pleose do not mix different types of batteries together.

SIGNAL CONNECTION OF TRANSMITTER AND RECEIVER

1. Switch on the drone power, place the drone on a horizontal plane, then open the remote control, both of their lights flash quickly at this time.
2. Push the throttle joystick to the top, hear a ‘drip’, and the remote light is fast flashing.then pull the joystick to the lowest point, another ‘drip’ will be hewed, the lights of the remote and drone change to steady on, that means the calibration is finished.

TRANSMITTER CALIBRATION

Apply transmitter calibration when the drone fails to take off vertically.
Standard version/Obstacle avoidonce version
Press the ‘One button calibration’ button. When the lights of drone are on and then start flashing and keep on again, the calibration is complete. the drone must be placed on ahorizontal surface in a steady state when the calibrationis conducted.
Camera ESC version
Move two joysticks to lower left lor lower right! same time, then it will sound a ‘drip”, meanwhile the drone lights flash quickly.Until the lights become steady on, the calibration is finished. When executing the correction command, it must be executed in a stable state parallel to the horizontal line, otherwise the correction effect will be affected.

START YOUR FLIGHT

1. One—key Ascend
Press the ‘One-key Ascend” button, the drone blades rotate and automatically fly to a height of 1.5 meters.
2. Basic Flight
Use the left joystick to control the flight altitude and turn left/ right, and the right joystick to control the forward, backward, left and right sidde flight directions.
Obstacle Avoidance Mode (The obstacle avoidance function is only available when you purchase the obstacle avoidance version)
Press the button to turn on the obstacle avoidance mode, and press again to turn off the obstacle avoidance mode. Avoid obstacles on four sides and retreat in the opposite direction of the obstacle.
It is recommended to turn on the obstacle avoidance function in an indoor flight environment with a length and width of 6 x 6 meters or more.When the UAV turns on the obstacle avoidance mode, the speed will slow down and the fast gear cannot be turned on. Therefore, it is recommended to fly indoors when the obstacle avoidance mode is turned on.
Flips & Rolls
When the drone go to 1 meter above, press flipping button and move the right- joystick to the left or right side, it will flip to the corresponding direction.
Right joystick
Headless Mode
The flight direction of drone is subjected to the direction of remote control.

1. When drone adjust the frequency, the drone is default as common mode. Then the indication light of drone is normally on. When you press the headless function key of remote control, the remote control beeps once and enters headless state. When you press the headless function key again, you listen to a long beep sound and the drone exits the headless mode.
2. In the headless state, operator doesn’t need to identify the direction of nose, but control the drone according to the operating lever of remote control.

Hover
When you release the left joystick (throttle) after the ascent/descent action, the dronewill hover at a certain height.
Left joystick

FINE—TUNING FUNCTION

If the drone lean to one side when hovering, fine-tuning can be used to correct its direction.
Press the fine-tuning button and hear a beep, then move the joystick in the opposite direction to adjust and calibrate until the aircraft does not deviate.
If there is no operation for 5-6 seconds after entering the fine-tuning, the fine-tuning function will automatically exit.

1. Forward/Backward Fine-tuning

2. Left/Right Side Fly Fine-tuning

Notes
When the drone is within 30cm from the ground, it will be affected by the blade vortex made by itself and become unstable. This is “ground effect”. The lower the drone is, the greater the effect will be.

FAQ

quadcopter battery in right way.
Too strong wind force.| Do not fly in windy days. The performance and the control of the quadcopter will beaffeded by the strong winds.
Fail to ascend| The rotation speed of main blades is too slow.| Push up the throttle joystick.
The battery of the quadrocopter is not fully charged.| Please full charge the quadcopter.
Landing too soom| The throttle stick is pulled down too fast.| Pull down the throttle stick slowly to perform a smooth landing.
Out of control| Beyond the effective controlling distance.| Ensure operation within the controllable distance: remote control of 100 meters and WIFI control of 40-50 meters.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

• Any changes or modivoid your authority to operate this equipment.RF Exposure Information
• The device has been evaluated to meet general RF exposure requirement.
• The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>