homestyles 5910-501 Queen Headboard Instruction Manual

homestyles 5910-501 Queen Headboard

Product Information

The product is a piece of furniture manufactured by homestyles. It is finished furniture designed for indoor use. The furniture should be cared for and used according to the provided instructions to maintain its quality and appearance.

Care Instructions

• Preventing Warping and Splitting: Liquids should never be allowed to remain on the furniture as absorption can cause warping and splitting of the parts, as well as delamination of the finishes.
• Avoiding Chemical Damage: Glass cleaners should never be used on the finished furniture as ammonia present in these cleaners can chemically attack the finish.
• Assembly with Power Tools: Power tools above 8 volts should not be used for assembling the furniture.
• Preventing Cracking: The furniture should not be placed in direct sunlight to prevent cracking.
• Preventing Fading: Writing directly on the surface of the furniture should be avoided to prevent fading.
• Preventing Marking: Hot objects should not be placed directly on the surface to prevent marking.
• Preventing Finish Damage: Rubber-based placemats should not be used as they can damage the finish.
• Preventing Discoloring: Commercial waxes and polishes should not be used as they may cause discoloration.
• Preventing Yellowing: To clean the furniture, a soft cloth moistened in lukewarm soap and water should be used, followed by buffing with a dry clean cloth to prevent yellowing.

Missing or Damaged Parts

If any parts of the furniture are missing or damaged within 30 days of purchase, homestyles will provide free replacements. Digital images of the defective parts may be required. Please note that replacements are only available for items purchased fromauthorized retailers. Fully assembled items do not have replacementparts available. To request replacements for missing or damaged parts, please contact homestyles Customer Service:
Website: www.homestylesfurniture.com
Email: servicedesk@homestylesfurniture.com
Phone: 888-680-7460

Assembly Instructions Queen Headboard

IMPORTANT
Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.

Parts & Hardware

Assmebly Steps

IMPORTANT

• Use a soft cloth between these parts and the floor.
• Do not use power tools above 8 volts to assemble.
• Do not tighten all the bolts until each part is properly assembled.
• Keep Wrench and Hex Wrench as the Nuts and Head Cap Bolts may need to be tightened in the future.

1. Insert Cam Lock Screws into pre-drilled holes in Crown (A), Posts (B), (C) and Stretcher (E), then tighten.

2. Attach Stretcher (E) to Headboard (D) with Dowels (short) and Cam Locks.

3. Insert Bolts into pre-drilled holes in Posts (B) and {C), then tighten.

4. Attach Posts (B) and (C) to unit with Dowels (long), Cam Locks, Square Washers and Nuts.
   Tighten Nuts with Wrench.
   

5. Attach Corner Plates to unit with Flat Washers, Spring Washers and Head Cap Bolts.
   Tighten Head Cap Bolts with Hex Wrench.

6. Attach Plates to unit with 5/8″ Flat Head Screws.

7. Attach Crown (A) to unit with Dowels (short), Cam Locks and 5/8″ Flat Head Screws.

Assembly Queen Footboard

IMPORTANT

• Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage.
• Carefully and strictly follow these assembly instructions to ensure a completed product as designed.
• Do not use power tools above 8 volts to assemble.

Parts & Hardware

Assembly Steps

IMPORTANT

• Use a soft cloth between these parts and the floor.
• Do not use power tools above 8 volts to assemble.
• Do not tighten all the bolts until each part is properly assembled.
• Keep Wrench and Hex Wrench as the Nuts and Head Cap Bolts may need to be tightened in the future.

1. Insert Bolts into pre-drilled holes in Posts (F) and (G}, then tighten.

2. Attach Posts (F) and (G) to Footboard (H) with Dowels (long}, Square Washers and Nuts.
   Tighten Nuts with Wrench.

3. Attach Plates to unit with 5/8″ Flat Head Screws.

4. Insert Cam Lock Screws into pre-drilled holes in Crown (A), then tighten.

5. Attach Crown (A) to unit with Dowels (short), Cam Locks and 5/8″ Flat Head Screw .

Asembly Queen Bed Rails

IMPORTANT

• Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage.
• Carefully and strictly follow these assembly instructions to ensure a completed product as designed.
• Do not use power tools above 8 volts to assemble.

Parts & Hardware

Assembly Steps

IMPORTANT

• Use a soft cloth between these parts and the floor.
• Do not use power tools above 8 volts to assemble.
• Do not tighten all the screws until each part is properly assembled.
• Keep Wrench as the Nuts may need to be tightened in the future.
• Do not slide bed on floor. To move assembled bed requires two people. Remove any bedding, then lift and carry bed.

1. Insert Bolts into pre-drilled holes in Headboard and Footboard, then tighten.
   

2. Attach Side Panels (I) to Headboard and Footboard with Square Washers and Nuts.
   Tighten all Nuts with Wrench. Insert Legs (K) into pre-drilled holes in Stretchers (J), then tighten.
   Attach Stretchers (J) to unit with Wood Screws into pre-drilled holes.
   Level unit by adjusting the adjustable levelers on bottom of legs.
   Note: Unit must be level to work properly.
   Note: Do not slide bed on floor. To move assembled bed requires two people. Remove any bedding, then lift and carry bed.

Assembly Instruction Night Stand

IMPORTANT

• Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage.
• Carefully and strictly follow these assembly instructions to ensure a completed product as designed.
• Do not use power tools above 8 volts to assemble.

Parts & Hardware

Assembly Steps

IMPORTANT

• Use a soft cloth between these parts and the floor.
• Do not use power tools above 8 volts to assemble.
• Do not tighten all the screws until each part is properly assembled.
• The unit must be level to work properly. Use the included adjustable levelers to level.

1. Insert Cam Lock Screws into pre-drilled holes in Top (A), Side Panels (B) and (C), then tighten .

2. Attach Rail (D), Bottom (E) and Back Panel (F) to Side Panels (B) with Cam Locks.

3. Attach Side Panel (C) to unit with Cam Locks.

4. Turn unit to its upright position.
   Attach Top (A) to unit with Dowels, Cam Locks and 1″ Round Head Screws.
   Level unit by adjusting the adjustable levelers on bottom of unit.
   Note: Unit must be level to proceed.

5. Attach Drawer Sides (G3) and (G4) to Drawer Back (G2) with 1 1/4″ Flat Head Screws.

6. Insert Drawer Bottom (GS) into groove. Attach Drawer Front (G 1) to unit with 1 1/4″ Flat Head Screws.

7. Attach Handle with Machine Screws. Note: Drawer assembly is not complete until 3/4″ Flat Head Screws are used in a later step.

8. Loosen slightly screws pre-installed on back of drawer front.

9. Insert drawer into unit, then adjust drawer front panel left or right and up or down until drawer gaps look proportional.

10. Pull drawer open slowly, then re-tighten screws from Step 8.
    Make sure drawer front panel does not move and lock drawer front panel into position with 3/4″ Flat Head Screws.
    Note: These 3/4″ Flat Head Screws must be installed to complete the drawer assembly.

11. Slide Drawer (G) into position.

homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer, homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
homestyles Customer Service: www.homestylesfurniture.com, servicedesk@homestylesfurniture.com, 888-680-7460

References

• homestyles Furniture — homestylesfurniture

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>