HOBBYWING QUICRUN 3652-3660 G2 Sensorless Brushless Motor User Manual

HOBBYWING QUICRUN 3652-3660 G2 Sensorless Brushless Motor

Product Information

The Sensorless Brushless Motor QUICRUN 3652/3660 G2 is a powerful brushless power system. It is important to use this product properly to avoid personal injury and damage to the product and related devices. Please read through this user manual carefully
and follow the specified operating procedures. Note that any unauthorized modification of the product may void the warranty.

Specifications:

• Model: QUICRUN 3652/3660 G2
• KV: Variable depending on the model
• LiPos: Compatible with LiPo batteries
• No-load Current: Varies depending on the model
• Diameter/Length: Varies depending on the model
• Shaft Diameter/Length: Varies depending on the model
• Bearing Size (mm): Varies depending on the model
• Poles: Varies depending on the model
• Weight: Varies depending on the model
• Applications: Suitable for RC cars and boats

Product Usage Instructions

Installation & Connection

1. Install the motor on the vehicle using the provided motor mounting holes. Make sure to use screws of appropriate length to avoid damage to the motor.
2. To connect the motor to an Electronic Speed Controller (ESC), there is no strict wire sequence requirement. The three wires of the motor (#A, #B, #C) can be connected at will. If the motor rotation is in the opposite direction, you can exchange any two wires.
3. Before powering on the ESC, check the reliability of the motor installation and the correctness of all connections.

Gearing

Proper gear ratio selection is crucial for optimal performance. Improper gear ratio may result in loss of power or damage to the motor. Consider the following points when selecting the gear ratio:

1. The running temperature of the motor
2. The desired speed and torque of the vehicle

Assembly and Disassembly

To ensure the motor has a longer service life and higher efficiency, it is recommended to regularly check the bearings and clean any dirt inside the motor. The frequency of maintenance depends on the usage and environmental conditions. Follow the steps below for assembly and disassembly:

1. Mount the motor rotor
2. Mount the rear end bell set
3. Fasten the rear end bell using the provided screws
4. Refer to the assembly drawing for a picture of the assembled motor

Note: Refer to the product manual for a detailed parts list.

Thank you for purchasing this HOBBYWING product! The power of brushless power system is powerful. Any improper use may cause personal injury and damage to the product and related devices. We strongly recommend reading through this user manual before use and strictly abide by the specified operating procedures. We shall not be liable for any liability arising from the use of this product, including but not limited to reimbursement for incidental or indirect losses. Meanwhile, we do not assume any responsibility caused by unauthorized modification of the product. We have the right to change the product design, appearance, performance and use requirements without notice.

Warnings

• Please carefully check power devices and manual of car frame to ensure the power pairing is reasonable. Avoid wrong pairing to overload and damage the motor.
• Always wire up all the parts of the equipment carefully. If any of the connections come loose as a result of vibration, your model RC may lose control.
• Never apply full throttle if the pinion is not installed. Due to the extremely high RPMs without load, the motor may get damaged.
• Never allow the motor case to get 100 degrees Celsius (212 degrees Fahrenheit) because the magnets maybe demagnetized by high temperature.

Specifications

Model

| ****

KV

| ****

LiPos

| ****

No-load Current

| ****

Diameter/ Length

| Shaft Diameter/ Length| ****

Bearing size (mm)

| ****

Poles

| ****

Weight

| ****

Applications

---|---|---|---|---|---|---|---|---|---
QUICRUN 3652SL 3250KV G2 QUICRUN 3652SL 4000KV G2 QUICRUN 3652SL 5400KV G2 QUICRUN 3660SL 3150KV G2

QUICRUN 3660SL 3700KV G2

| 3250KV

4000KV

5400KV

3150KV

3700KV

| 2-3S

2-3S

2S

2-3S

2-3S

| 4.0A

5.3A

6.8A

5.4A

6.5A

| ****

ϕ=36mm(1.42″)

L=52mm(2.05″)

ϕ=36mm(1.42″)

L=60mm(2.36″)

| ****

ϕ=3.175mm(0.13″)

L=15mm(0.59″)

ϕ=5mm(0.20″)

L=18.5mm(0.73″)

| ****

Front：D13D5T4 Rear：D13D5T4

Front：D16D5T5 Rear：D13D5T4

| ****

4

| 223g| ****

1/10 On-road, Buggy, Truck (Light load)

224g
224g
273g| ****

1/10 Truck, Monster truck

278g

QUICRUN 3652SL-G2

QUICRUN 3660SL-G2

Installation & Connection

1. Install the motor
   There are 6 motor mounting holes in M3 specification, and the mounting holes are 5.5mm in depth, before installing the motor on the vehicle, please carefully confirm whether the specification of the screws is appropriate according to the thickness of the motor mounting plate to avoid damage to the motor due to too long screws.

2. How to Connect the Motor to an ESC
   There is no strict wire sequence requirement for the connection between the motor and the esc, the # A/# B/# C three wires of the motor and esc can be connected at will, if the motor rotation in the opposite direction, you can exchange any two wires.

3. Inspection
   Before power on the esc, please check the reliability of the motor installation and the correctness of all connections.

Gearing

Reasonable selection of gear ratio is very important. Improper gear ratio may bring you great loss. You can select the gear ratio according to the following points!

1. The running temperature of the motor
   The motor temperature should be lower than 100 degrees Celsius (212 degrees Fahrenheit) in operation. Because high temperature may cause the magnets to get demagnetized, the coil to get melt and short circuited, and the ESC to get damaged. A suitable gearing ratio can effectively prevent the motor from overheating.

2. The principle of selecting gear ratio
   To avoid the possible damage to ESC and motor caused by the overheat, please start with a small pinion/a big FDR and check the motor temperature regularly. If the motor and ESC temperature always stay at a low level during the running, you can change a big pinion/a low FDR and also check the motor temperature regularly to ensure that the new FDR is suitable for your vehicle, local weather and track condition. (Note: For the safety of electric devices, please check the ESC and motor temperature regularly.)

Assembly and Disassembly

In order to make the motor have longer service life and higher efficiency, we suggest to regularly check the bearing and clean the dirt in the motor. The specific time depends on the frequency of using the motor and the site conditions. When installing, please follow the steps in the following assembly drawing; when disassembling, follow the reverse steps.

Parts List

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>